Search Documents

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

By D. J. Zhao

The reduction of ilmenite pellets was investigated at 950°C and 1000°C under a CO-N2 gas mixture with 10 L/min gas flow rate. All the reducing reactions were conducted in a furnace with a thermogravimetric analysis system. The reduction rate is higher at 1000°C than that at 950°C. At the early stage of the reactions, with the CO concentration increasing in the gas mixture, the reduction rate increased at 1000°C. In addition, at the early stage of the reactions, a rapid temperature increment and a rapid conversion of oxygen were observed on the curves of temperature versus time and conversion of oxygen versus time under different experimental conditions. The solid reaction products obtained in these experiments were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometers (EDS). Metallic Fe with small amount of Ti dissolved in it and oxides of Ti were found in the solid reaction products, but the formation of any nitride phases was not found under the prevailing conditions.

Jan 1, 2014

By P. K. Fedotov

Centrifugal separation opens its new application fields in the Mining Industry. The up-to-date equipment for ultra-fine ore and concentrates grinding allows an efficient use of centrifugal concentration for micronic gold grains recovery. Moreover, advanced centrifugal concentrators are presented on the market: concentrators with continuous concentrate discharge designed both for ore and non-metallic minerals concentration process. The conducted tests proved the centrifugal concentration to be efficient process for gold recovery from finely ground concentrates and ores (less than 20 µm). Knelson concentrator application for such a fine material in different process circuits makes possible to raise the total gold recovery level of plants. In the circuits of coal plants and in course of coal slimes treatment the centrifugal concentration may be used before flotation in order to improve process performances. A centrifugal concentrator KC-CVD with continuous concentrate discharge working on 0.3 (0.5)mm fraction before flotation is

Jan 1, 2014

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014

By A. O. Gapchich, T. N. Matveeva, N. K. Gromova

"Tin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. The aim of the work is an experimental study of the modification of the surface of sulfide minerals and cassiterite by stable metal-collector complexes to increase extraction of fine tin, silver, copper and other metals from complex tin ores. Triamide cyanuric acid (TCA) was studied as a thin silver flotation modifier. Thermophilic polymer with a functional group of phenylphosphine TMPPh was used as a selective flocculant. For experimental studies of the physical and chemical effects of collecting agents on the surface of minerals the following analytical techniques were used - the analytical scanning electron emission ASEM (LEO 1420VP INCA OXFORD ENERGY 350) and laser (KEYENCE VK-9700) microscopy, measurements of electrode potentials of mineral anthills by potentiometric titration, monomineral and pulp flotation. New data on formation of the adsorbed layer of DBDTC on the surface of chalcopyrite, galena and arsenopyrite were obtained, and the dimensions of the reagent films and the strength of their adsorption. The indiscriminateness of cassiterite to DBDTC ensures its selective separation into a chamber product during the flotation of sulfides. It is shown, that modification of the sulfide surface by stable complexes Me-DBDTC and Ag-TCA-TMPPh will increase the recovery of non-ferrous metals and silver into a collective sulfide concentrate and will provide a high-quality tin concentrate for flotation of tin sulfide ores.The studies were perfomed with the aid of the Russian Science Foundation (Project No. 17-17-01292).INTRODUCTIONTin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. In this regard, it seems advisable to use new varieties of flotation reagents in order to increase extraction of finely dispersed tin, silver, copper and other non-ferrous and precious metals from multi-metal tin ores (Bocharov and Ignatkina, 2007; Khanchuk etal., 2012; Wu and Zhu, 2006; Yusupov etal., 2016)."

Jan 1, 2018

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By Bruce Mathema, Steven Huynh, Terry Cheng, Gerry Gomez

"The use of PM40N, a specialty precious metals promoter in conjunction with a standard Xanthate based collector was extensively investigated in the flotation of a complex, silver-bearing, lead-zinc ore containing naturally occurring graphitic gangue. The ore, considered difficult to treat with conventional reagents, was tested at plant scale to determine the impact of the promoter on silver recovery, lead grade and also on the amount of zinc misplaced to the final lead concentrate.Initial laboratory-scale rougher flotation testing implied significant improvements in the recovery of silver and lead with a marginal amount of zinc displaced. Subsequent mini pilot flotation tests further revealed that a gain in selectivity and recovery could be achieved by adjusting PM40N promoter dosage and incorporating a cleaner flotation step, further improving rejection of sphalerite. Plant trials resulted in an improvement of 3% in Silver recovery coupled with a 2% increase in recovered lead whilst maintaining lead grade in the lead circuit.To date, the use of PM40N as a promoter has enabled the processing operation to significantly increase its plant economics. The partial replacement of the standard Xanthate based collector has also reduced the overall quantity of Xanthate required in the standard circuit by approximately 10% - which is a positive impact on the environment. It is envisaged that further optimization of plant parameters will favor stable operation and continue to boost revenues generated by subsequent improvements in silver metallurgy."

Jan 1, 2014

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

The Indian steel industry is growing at a rapid pace and expected to be the 2nd largest steel producer in the world after China. To cope up with this growth and to sustain it, the industry needs to focus on effective utilization of domestic metallurgical coals. While the importance of indigenous coal has increased, its supply from the domestic sources is declining. This is primarily due to high ash content in Indian coals leading to its difficulty in washing to a low level competitive to imported coals. Non-availability of a suitable beneficiation technology to bring down the ash to such a low level is the other reason. Effective utilization of current technologies has enabled Tata Steel to bring down the ash to 13-16% from its captive collieries. However, further lowering the ash using the conventional beneficiation technologies is difficult and unsustainable. New technologies should be developed for bringing down the ash further. A thrust area research program has been undertaken at Tata Steel for producing clean coal with 8% ash maintaining the yield currently achieved in its washeries. The technologies attempted are based on chemical beneficiation of coal. In leaching process, suitable chemicals are used for extracting ash minerals from the coal. As an alternative process, the combustible part of the coal is being extracted using a suitable organic solvent through an organo-refining process. Both the processes have been successfully developed in the laboratory and are being demonstrated in pilot scales. Various beneficiation processes practiced at Tata Steel including the efforts made for developing new processes for achieving clean coal with 8% ash have been discussed in this paper. Keywords: metallurgical coals, washing, beneficiation technologies, chemical beneficiation, leaching, solvent, and organo-refining process

Sep 1, 2012

By Leming Ou, Hongqiang Li, Li Zeng, Qiming Feng, Yiping Lu, Guofan Zhang

"The entrainment of sericite, especially in the presence of hydrophobic microcrystalline graphite, leads to the poor flotation selectivity of microcrystalline graphite ore. In this paper, it was attempted to reduce entrainment of sericite, selective flocculation of microcrystalline graphite using polyethylene oxide (PEO) was studied. For the sake of flocculate microcrystalline graphiteselectively, flocculation tests of microcrystalline graphite and sericite single mineral were conducted.To investigate the effect of selectiveflocculation of graphite on entrainment of sericite in microcrystalline graphite flotation, batch flotation tests of graphite single mineral and artificial mixtures were conducted; theflocculationselectivity of PEO of different molecular weight (M.W.) was alsocompared inartificial mixture flotation. Inthe end, the structure of flocs in different particle size was studied by sieve analysis and microscopic observation. The resultsindicated that PEO of molecular weightone million andtwo million could selectivelyflocculate the microcrystalline graphite and reduce the entrainment of sericite at a lower dosage; further increasingof the dosage of PEO(M.W. ?two million) led to hetero-flocculation between graphite and sericiteandmadethe ash content of concentrate increase again."

Jan 1, 2014

By Z. Y. Ma, M. D. Liu, Z. Z. Liu, J. K. Zhou

"An optimization method of microwave assisted leaching of copper anode slime was proposed based on Taguchi method. The results showed that the solid-liquid ratio was the most important factor affecting SNR(signal noise ratio) of the copper, tellurium and selenium leaching efficiencies, and its contributions to the copper, tellurium and selenium leaching efficiencies were 58.34%, 55.54% and 60.74%, respectively. Solid-liquid ratio was a significant factor to SNR(copper, tellurium and selenium). Reaction period was a less significant factor to SNR(copper and tellurium) and concentration of sulphuric acid was a less significant factor to SNR(selenium) while microwave power was an non-significant factor, its contributions to the copper, tellurium and selenium efficiencies were 3.22%, 11.73% and 12.73%, respectively. The optimized parameters of the microwave assisted leaching of copper were as follow: microwave power of 500 W, reaction period of 10 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The optimized parameters of the microwave assisted leaching of tellurium and selenium were as follow: microwave power of 800 W, reaction period of 15 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The validation experiments under the optimized conditions has been carried out, the copper, tellurium and selenium leaching efficiencies were 98.66%, 84.32% and 64.54%, respectively. INTRODUCTION As important valuable by-products, copper anode slimes are collected from the bottom of the electrolytic bath in the electrolytic copper refining process(Kilic, 2013). The value of the anode slime is determined by the content of rare metals and precious metals(Liu, 2014). Generally, pretreatment of copper anode slime is the first stage of the whole process. The aim of the pretreatment process is to remove Cu, Te and Se etc and enrich the valuable metals. The methods of pretreatment process can be differentiated into: pyrometallurgical processing and hydrometallurgical processing(Amer, 2003). The hydrometallurgical processes are more promising compared to pyrometallurgical processes in terms of cost effectiveness, low energy consumption and environmental concerns(Ranjbar, 2014). However, the disadvantages of the hydrometallurgy process are evident, such as lengthy processing times and low efficiency. Therefore, it is necessary to develop a highly efficient and environmentally friendly pretreatment method."

Jan 1, 2018

By W. G. Liu

Phenyl malonic acid (PMA), a new chelating collector, which contains a phenyl structure and a malonic acid chelating group, has been synthesized and its collecting capabilities to calamine, hematite, quartz and hemimorphite are also studied in laboratory. From the experimental results, it can be seen that the PMA has somewhat flotation ability to calamine, hematite and quartz, while it nearly has no collecting ability to hemimorphite. With the increase of PMA concentration, the flotation recovery of calamine increases. When the dosage of PMA was 560g/t and at pH=7~9, the flotation recovery of calamine gets its maximum of 45.94%. The test results about the influence of pH on the flotation recovery of quartz show that the flotation recovery increases with the increase of pH, and the maximal flotation recovery can be gained in alkaline media. On the other hand, PMA has stronger flotation capability to hematite than to other minerals. The flotation recovery of minerals increases with increase of PMA concentration. When the dosage of PMA is 560g/t and at pH=5~7, the flotation recovery of hematite is 82.96%. Mean-while, the influence of pH on the flotation recovery of hematite was studied and test results showed that, as pH increases, the flotation recovery sharply rises until pH=4, then the increasing rate de-creases outstandingly, at pH=6 the flotation recovery reaches its maximum of 82.96% and it de-creases speedily in alkaline media. Finally, through the measurement of infrared spectroscopy and in terms of solution chemistry of collector, the flotation mechanism has been discussed. It was concluded that the adsorption of PMA on minerals surface is chemical adsorption in nature through two oxygen atoms in the polar group of phenyl malonic acid chelating with the metal ions of minerals surface to form a hexagon-cycle chelate complex: C(=O)-O-M-O-(O=)C.

Jan 1, 2014

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By A. Yörükoglu

In this study, thorium mineral that found in the complex ore deposit bearing bastnasite, fluorite, and barite from Eskisehir - Sivrihisar district has been tried to extract by using HCl and H2SO4 leaching. Ore sample of approximately 3 tons taken from the ore deposit has been homogenized in order to obtain composite samples by means of ore preparation techniques for experiments. Results of chemical analyses of composite samples are as given; 40.8% CaF2, 35.35% BaSO4, 2.01 Ce, 1.5% La, 0.39% and 0.1% Th. HCl and H2SO4 leaching processes have been performed to gain Th in the ore. For determining the optimum particle size, the samples have been ground under controlled conditions and brought to the sizes of 0.065, 0.2, 1 and 3 mm. Leaching experiments have been carried out in both HCl and H2SO4 acids without roasting and roasting at the temperature of 900°C for 1, 3 and 6 h retention times for all particle sizes determined before. In the experiments, the highest Th recoveries reached are as follows; 78.74% Th when H2SO4 and 1 mm particle sized sample used, and 1 h roasting applied and 73.38% Th when HCl and 1 mm particle sized sample used, and 3 h roasting applied. Keywords: thorium, leaching, concentration, sivrihisar, roasting

Sep 1, 2012

By Li Tianxia, Zhou Jing, Zhu Yimin

"A typical low-grade of high sulfur bauxite fr contains 54.71% Al2O3, 11.35% SiO2 while the ratio of aluminum and silicon was 4.25, and harmful components such as Fe and S graded 7.3% and 1.33% respectively. The ore is characterized by complex mineral compositions, fine dissemination of particle size of pyrite and diaspore, low desulfurization efficiency, and difficult separation of aluminum and silicon. In order to improve the degree of concentration, recovery and desulfurization efficiency on the basis of process mineralogy studies, the floatation behavior of high sulfur bauxite in the process of desulfurization and desilication were studied through laboratory tests and pilot plant tests. KEYWORDS high-sulfur bauxite; low grade; flotation; desulfurization;desilicication INTRODUCTION In order to solve the selection problem of bauxite mine area, we carried out technological mineralogy, laboratory test, small-expansion Dalian test to solve the problem of the refractory ore. Main research contents and conclusions were presented as followings :(1)Process mineralogy research shows: the main mineral components include diaspore, kaolinite, chlorite, pyrite, limonite. (2)Batch flotation tests indicated that slime can be dispersed well during desulfurization floatation when Na2CO3 was used as modifying agent. (3)Poilot plant tests shows that Batch flotation tests results are correct. 2?PROCESS MINERALOGY 2.1 Chemical Composition of Ore 2.1.1 Spectral Analysis of Sample The results of the semi-quantitative analysis of X-Ray -fluorescence spectra of the original ore are shown in Table 2-1. The results of spectral analysis show that the main components of the sample are O, Al, Si, followed by Fe, Mg, Ti, S and so on, while the content of other elements is very small. The value is Al, and maybe Ti, for bauxite, while Fe and S are unfavorable elements, and Si and Mg and Ca are the main impurity elements."

Jan 1, 2018

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By Dingwu Feng, Jannie S. J. van Devente

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated in two slurry systems, i.e. gold cyanidation and geopolymerisation. The kinetics of gold extraction were significantly enhanced and the cyanide consumption was reduced in the cyanidation of a pyrite concentrate using ultrasonication, probably due to the prevention of leaching passivation, the improvement of the dissolution of the gold host sulphides and the oxidation of soluble sulphides to sulphate. The effectiveness for ultrasonication was improved with the injection of oxygen and the addition of dithiophosphate through enhancing the formation of the oxidation radicals and selectively inducing cavitation bubbles directly at the sulphide interfaces. Ultrasonically enhanced cyanidation could render currently uneconomic deposits viable for extraction by improved cavitation efficiency with the aid of surfactants.Ultrasonication increased the compressive strength of the formed geopolymers through accelerating the dissolution of the Al-Si materials, strengthening the bonds at the solid particle/gel phase interfaces, enhancing the polycondensation process and improving the formation of semi-crystalline to crystalline phases. The use of power ultrasound will yield high-performance geopolymer materials."

Jan 1, 2003

By M. F. He

The depression of pyrite in marmatite flotation by a new depressant Sodium Glycerine-xanthate (SGX) has been investigated through microflotation, zeta potential, and adsorption measurements in systems open to the atmosphere. The flotation tests of single mineral show that in the presence of SGX, marmatite can be activated by Cu2+ and shows good flotability, while pyrite can?t be activated and therefore shows poor flotability, as a result these two minerals can be separated using butyl xanthate as the collector. The depression mechanism of SGX on sulfide minerals is discussed based on Zeta potential and adsorption isotherm. Zeta potential experiments demonstrate that at the presence of Cu2+, SGX can strongly adsorb on the surface of pyrite, while it can?t adsorb on the surface of marmatite, thus the results are in accordance with those of flotation experiments; the results of adsorption isotherms show that the adsorption density of SGX on pyrite is greater.

Jan 1, 2014

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012