Search Documents

By J R. "Dick" Daniel

Over the past several years, the Hercules Technical Service Group for the Explosives Department has produced a series of programs for the TI59 programmable calculator dealing with explosive application problems. These programs have been made available to both our internal staff and to the Hercules explosives distributor organization. Several of these programs have found good acceptance and wide usage.

Jan 1, 1984

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer, John M. Jr Pitlo

Repelling charges are small explosive charges detonated to frighten and drive fish away from a blasting zone just prior to detonation of a major explosive charge. Use of repelling charges has been recommended by natural resource agencies to mitigate the effects of submerged explosives. Blasting companies have used this technique in a "good faith effort" to reduce potential damages to aquatic resources. It has been assumed that noise or pressure generated by the small charge will drive fish from the immediate area, thereby reducing impacts from the much larger and potentially more-damaging blast.

Jan 1, 1997

By Lawrence C. K Hu

The release of load mechanism during rock breakage by explosives was founded by Dr. T. N. Hagan & published at the Sixth International Colloquium on Gasdynamics of Explosions and Reactive Systems Stockholm, Sweden, 1977.

Jan 1, 1995

By J W. Edl, F C. Wu

In instrumented model rock blasting experiments in granite blocks, best fragmentation results were obtained when delays between holes were 1 to 2 milliseconds per ft. of burden and when a rectangular shothole pattern was used with spacings larger than the burden. Effective fragmentation in multiple hole blasts seemed to depend primarily on the full development of the crack network around each hole before the charge in the next hole was detonated. The test results showed that simultaneous or almost simultaneous initiation of shotholes in bench blasting resulted in poor fragmentation.

Jan 1, 1975

By Paul D. Dupree

This paper discusses the drilling and blasting techniques used in blast casting at a large western coal stripping operation.

Jan 1, 1986

By Deane Tunaley, Paul Tidman, Qian Liu, John Mullay

Laboratory studies have indicated that the crystallization and desensitization of microballoon sensitized emulsion explosives start immediately after shocking or pre-compression. However, the question of whether or not the shocked emulsion could be worsened by the growth of crystallization or recovered by rebounding back to lower densities has been rarely examined under actual rock blasting conditions. This study was primarily intended to investigate the desensitization characteristics of two commonly used emulsion products in terms of blasthole spacing and delay duration. In the experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1995

By Larry D. Lawrence, Gerald W. Greenway

Corrugated boxes have been the dominant shipping container for packaged commercial explosives for the past 3 decades. Recent changes in shipping regulations have dictated to the industry the adoption of enhanced standards dealing with the construction of fiberboard shipping containers for explosives. Effective October 1944, all shipping containers used for explosives will require individual certification verifying that the containers conform to the United Nations performance oriented packaging standards. The U.S. Department of Transportation will continue to enforce compliance to the new UN standards. A renewed emphasis on the design of corrugated shipping containers to insure industry compliance to the UN standards has been a joint development program between the explosive manufacturers, fiberboard container suppliers and the academic community. Along with drop strength, leakproofness, and vibration resistance, the individual stacking strength of corrugated shipping containers has come under tight scrutiny based on the new UN standards.

Jan 1, 1994

By Othmar Mueller

Building demolition techniques using blasting are different depending on the structure of the building, on surroundings, traffic, debris-transport systems, and re-usability of salvaged building materials, etc. This paper outlines some of the trends and problems in demolition blasting technique in Europe and especially in Hungary.

Jan 1, 1975

By Lyle Avey

For the purpose of this paper, testwork and general pre-splitting practice will be discussed for the Chimney Creek Mine.

Jan 1, 1990

By Jerry R. Wallace

Infrastructure improvements and industrial plant expansion and modernization often require rock blasting within 20 feet of existing structures. In many instances trenchlines must cross beneath existing in-serv1ce utility lines.

Jan 1, 1994

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

This paper is written in response to a request from the UTRC Committee on Perimeter Control Blasting. That Committee is conducting "follow-on" research on the selection of appropriate blasting designs and products for perimeter control of rock excavations. This paper will deal with the rock mechanics principles which affect the outcome of such blasting, and explain to the reader how to apply techniques which will modify the typical site response one would expect for conventional blasting methods. For convenience of reference, and to emphasize the important concept that the application of this technique is site specific, that is it must be custom-designed for each site, the technique is being called "Modified Site Response Blasting".

Jan 1, 1984

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

The basic metric for linear shaped charge performance is the amount of cutting distance that the charge can effectively yield given a specific standoff and target. Due to its size and restricted production runs the 10,500 grain/foot (2,232.25 grams/meter) linear shaped charge has had only limited studies that examine cutting performance and standoff. This article covers research regarding cutting performance verses standoff as the charge is applied to common structural steel. Specifically this study uses A36 mild carbon structural steel blocks of 10.16 cm by 11.80 cm by 35.56 cm and standoff distances of 0.5, 1.0, 1.5, and 2.0 charge diameters. Data presented includes the presentation of actual cutting performance numbers, comparison of that data to projected performance based on currently recognized industry guidelines, and a discussion of what may contribute to the performance found in this study.

Jan 1, 2013

By D K. Joyce, B Mohanty

In a previous paper, it was shown that a lack of clear understanding of the role of initiation mode on detonation characteristics often leads to under-utilization of the explosive system in blasting. This is of particular significance since the very large number of explosive initiation practices currently in use implicitly assumes that the blasting performance of an explosive is largely independent of the exact mode of initiation. This paper deals specifically with bulk-loaded and pneumatically-loaded ANFO under various initiation modes in small diameters. These include initiation by booster and detonating cords of various strengths, and combination of cords and boosters. The nature of energy release and energy partitioning between shock and gas energy have been studied in the underwater test as a function of charge diameter. The paper describes the relative merits of various initiation modes for specific charge geometries and confinement, under end- and side-initiated conditions. Guidelines have also been formulated for use in the field to match initiation practice with blasting requirements.

Jan 1, 1994

By Robert Slivinski, Kyle Hobbs, Michael Stern, John Willox, Brad Jewson

Prairie Mines & Royalty Ltd. produces over 12 million tonnes annually of thermal coal for TransAlta’s Sundance and Keephills power stations from the Highvale Mine. This opencast mine is next to a lake and is surrounded by cottages and farms, which means that blast vibrations and air overpressure have to be kept to a minimum.

Jan 1, 2008

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By Brian W. Stump

The cessation of testing of any nuclear explosive devices in all environments is the goal of the Comprehensive Test Ban Treaty. In order to assure compliance with such a treaty, an international monitoring system has been proposed. This system will include seismic, infrasound, hydroacoustic and radionucleide monitors located throughout the world. The goal of this system is the detection of any nuclear test. In preparation for this treaty, a series of monitoring system tests, focusing primarily on seismic observations, have been undertaken. The most recent of these tests, Group of Scientific Experts Technical Test Three (GSETT-3), provides valuable data for assessing future monitoring systems. During the course of this experiment, seismic events associated with earthquakes, nuclear explosions and mining explosions have been recorded. This presentation will discuss the numbers and types of mining explosions triggering the system, in a particular area. Possible implications for the mining industry will be explored.

Jan 1, 1997

By Salah A. Taqieddin

The blast casting technique of removing overburden is an innovative technique which was successfully used in the mining of certain surface coal and quarries. This method was found to be efficient in minimizing the labor and equipment cost while accelerating mining operation with safety. This method was successfully applied to horizontal as well as to dipping coal seams. Also it was practically applied to single as well as to multiple ore bodies

Jan 1, 1992