Search Documents

By Jeff Friedman

This paper addresses certain problems to be encountered when a blasting contractor agrees to provide indemnification. Nearly 100% of all blasting work is performed pursuant to a contractual agreement. Whether the explosives engineering firm works directly for the property owner, or for a general contractor by way of subcontract, indemnification agreements are generally required to protect owners, operators, general contractors, and other interested parties in the event there is subsequent litigation. These contractual requirements are typically referred to as indemnification and “additional insured” agreements. We will address the ramifications of contractual indemnification as well as “additional insured” agreements in this presentation. Some of the aspects of this paper will include:

Jan 1, 2004

By Pierre Allard, Wilfrid Comeau

Near-field and close-in blasting can be safe and efficient, near engineered structures, if the dynamic reaction of structural members to blasting vibrations are considered. Safe particle velocity criteria can be derived from allowable safe static flexural deflections and critical frequencies. Control of close-in blasting can be accomplished using low-pass filtering of the particle velocity signal at the critical frequency. The CETE Mediterranee laboratory at Aix-en-Provence, France, a branch of the Ministry of Roads and Bridges has -pioneered this approach and successfully applied it to major road cuts and tunnels in built-up areas, as well as a major powerhouse expansion project in Africa. This approach is presently being used for a spillway rehabilitation project in Quebec, Canada. This paper exposes- the theoretical aspects and gives case histories of its use. The SCS-15 an automated, peak reading, data acquisition device is described.

Jan 1, 1991

By Lon Santis

This paper describes several applications of quantitative risk assessment in the management of commercial explosives operations. The Institute of Makers of Explosives’ (IME) quantitative risk assessment software modeling program IMESAFR was used for this analysis. Modeled activities include the unloading of a ship at port, locating a safe haven, and dealing with encroachment on a manufacturing facility. The layout of actual explosives sites were used for the analysis. The risk of fatality is analyzed and shown it can be used to make informed operational decisions for each activity. A study of the risks to individuals from activities involving commercial explosives compared to individual risks from other daily activities or exposures is also presented.

Jan 1, 2008

By Zhang Shixun, Wang Xuguang, Wang Guoli

A massive millisecond blast at an open-pit mine of large scale can be realized by using the blasting technology of pre-loaded explosives, which can enlarge production scale, reduce the frequency of blasting and of large production equipment movement, and raise the production efficiency. The reason why application of this technology is restricted at high sulfide ore deposits of variable and complex geological conditions is that an exothermic reaction will take place when explosives contact sulfide ores, which could lead to accidents such as spontaneous burning and detonation of explosives pre-loaded in boreholes, influencing blasting and production safety. The thermal decomposition reactions of emulsion explosives of different prescriptions in contact with pyrite have been studied by differential thermal analysis (DTA), kinetics parameters calculation and accelerating rate calorimetry (ARC), and on the basis of the above studies, the safety of emulsion explosives used in sulfide mines has been evaluated with the safe contact time of different emulsion explosives with pyrite determined.

Jan 1, 1998

By Kenneth Medearis

The accurate prediction of possible damage to historic structures subjected to blasting-related ground motions is not infrequently the dominant factor in whether or not a mining or quarrying operation is allowed to proceed. A recent scenario involving an 1802 Pennsylvania Historic House was resolved satisfactorily, primarily because of the use of modern structural dynamics analysis techniques rather than simplistic peak particle velocity guidelines. One of the associated dominating factors was the truly significant agreement of the analysis results and the values obtained from actual on-site test shot blast motion recordings.

Jan 1, 1993

By H Fukui, K Ichikawa, K Aikou, E Suzuki

An electronic delay detonator (EDD) consisting of a digital-base electronic delay module and a conventional instantaneous detonator module, designed for series connections with a special adjustable-output blasting machine, is described and shown to provide a delay time accuracy some four to twelve times higher than that of pyrotechnic millisecond and decisecond delay detonators, together with the other performance characteristics necessary for practical use. Also described is a blasting design system which allows effective reduction of ground and air vibration, through the use of EDDs with optimum delay times as determined by accurate computer simulation based on wave form and other data obtained from an on-site single-shot test blast.

Jan 1, 1989

Blasting is a very cost effective method of rock fragmentation but its uncontrolled application often results in excessive damage to the perimeter of an excavation. Several perimeter control techniques are available but tracer blasting is commonly used in Canadian underground mines for overbreak control. This involves tracing a column of Ammonium Nitrate-Fuel Oil (ANFO) with a detonating cord. In order to investigate the techno-economic effectiveness of tracer blasting in perimeter control, a field experimentation was conducted which involved blasting in sublevel caving and sublevel sloping operations, experimental drifting, benching and pipe tests.

Jan 1, 1997

By Jhon J. Silva Castro

Blast vibration records used in mining contain unwanted information in the form of noise due to long-period drifts, background noise, and noise due to the conversion of the analogue signal to a digital signal. When recorded signals from blasting are used to find other physical variables, such as going from particle velocity to acceleration or displacement, the additional information in the vibration signal can result in inaccuracies in the estimation of the peak values and more dramatically, the results in displacement or acceleration can be nonzero near the end of the record. There are different proposed methods to clean or filter the unwanted information from the signal. All of the methods are based on finding the best fit of the record average value (baseline) and then subtracting from the record under analysis to produce the desirable adjustment. Different criteria and functions are used to define the best fit. The function to use will depend on the shape of the record average values. The main characteristic of the baseline function is that it represents a low frequency wave. Such a low frequency wave can be a periodic function or a polynomial expression of nth order. According to the order of the polynomial expression, the baseline correction can be linear, parabolic or high order. In this document the detailed procedure and the results for the baseline correction of a blast vibration record using a periodic function and a polynomial expression of different order is presented. The results show that the drift problem when displacement is calculate using velocity records increases with the increase of the distance from the blast.

Jan 1, 2015

By Bert Bahnson

As farms decrease and subdivisions increase there is a continuing demand for easy and safe silo removal. A few years ago I attended one of the Omni istribution explosive classes and was impressed by a product designed by Omni owner Bill Nixon called the Omni Breach. Its original purpose and main current use is law enforcement; specifically door breaching and tactical operations, with most of the force coming from water using a minimal amount of explosive component. I experimented with various charge strengths on concrete and found that it can be easily shattered with little flyrock or airblast. A neighbor of mine had an old silo within a foot of a barn that he was rebuilding and inquired about its removal. His property was sandwiched between an elementary school and Interstate 40, so I told him that I would do some test shots and if the results proved satisfactory, I would take the job for free to test the following theory.

Jan 1, 2006

By John F. Mitchell

Large production blasts involving many series in parallel have long been a source of complication. When speed and accuracy are most necessary in blast preparation an efficient and precise method of wiring is required. After loading a large number of holes and being pressured for time, due to lack of daylight, equipment shutdown, etc., an effective hook-up plan can eliminate many last minute problems. It is the intention of this paper to offer a simplified wiring proceedure which when employed can save precious time and encourage efficient and economical utilization of blasting personnel and material.

Jan 1, 1976

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993

By Harry Verakis, Thomas Lobb

Widespread use of ammonium nitrate compositions for mine blasting operations has led to various bulk transport vehicles designed especially for the explosives industry over the past half century or more. The advancements in explosives technology and continuing developments in bulk transportation have resulted in a variety of blasting agents and, more recently, oxidizers being transported and used from specially designed bulk transport vehicles. It is estimated that about 2000 bulk transport vehicles are used in mining operations. Many of the bulk vehicles carry about 15,000 to 33,000 pounds (6808 to 14,968 kilograms) of payload and some can carry up to 50,000 pounds (22,679 kilograms) for large open cast mines. Thus, it is imperative that detailed knowledge and safety instructions are available from the blasting personnel and mine management should an unplanned incident such as a fire occur with a bulk transport vehicle at a mine site.

Jan 1, 2008

By Dae-Woo Kang, Sang-Wook Kim, Shin Lee

The Air-tubes blasting method is provided in which a series of aligned boreholes are charged with explosive s and air tubes in a predetermined blasting pattern. The air tube is composed of cylindrical flexible tubes which have a predetermined width and length to be fit with the site boreholes. Within a preferred formation, each borehole is charged with the explo sives and detonators with an air tube installed just above the explosives. Stemming materials are filled above the air tubes. At the limestone mine of Sung-Shin Cement Co., in South Korea, these blasting tests were performed by a diameter 102 millimeter and 15 m long boreholes with the charging length of explosives was 8m to 10 m by the total weight of explosive 40 to 50 kg with 3m to 6m air tube which has a 76 mm diameter, and 1m to 3m stemming cover. Blasting results showed the about 10% to 30% explosives savings available and especially, the about 20% to 50% reduction of ground vibration with the low noise measures around 2dB to 5dB by this new blasting method which was compared with the conventional blasting methods. The explosives and air tubes may be alternately charged along the boreholes. The use of air tubes which were charged above an explosive layer allow to form the quantitative air decking in every blast hole. Therefore, the Air-deck effect can be easily obtained through this blasting method, and also easy to increase the fragmentation rate resulting in the more suitable mucking procedures at the working site with the minimum usages of explosives for the better economic operations in mine quarries.

Jan 1, 2005

By Richard A. Dick

Few topics in the blasting industry are more controversial than the proper riming procedure for large-diameter ammonium nitrate-fuel oil (AN-FO) charges, despite the considerable amount of research that has been done both in the laboratory and in the field. The January, April, and June 1975 issues of Emphasis on Blasting contain interesting discussions on priming (5). An ideal primer is one that will surely and efficiently initiate the AN-FO column at the correct location to assure optimum blasting performance. During the 20 years of AN-FO's existence, singlepoint priming, axial priming, multiple-point priming, thermal priming, and shock riming have all been advocated as the "optimum" method. This is not surprising because blasting specialists have often differed on even the most fundamental concepts. To define the optimum primer, we must know what detonation characteristics in the AN-FO column are most desirable. Again, authorities disagree. This paper will discuss conclusions of various studies in an attempt to clear up some of the confusion.

Jan 1, 1976

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yukio Kato, Yuji Wada, Yoshikazu Hirosaki

Smooth blasting technique is widely applied for tunneling road or railway construction in Japan. However, smooth blasting technique often causes problem related to detonation failure in explosive column due to channel effect. Channel effect is attributed to the precursor air shock wave (PAS), which propagates ahead of detonation front in an air channel of borehole. PAS precompresses and desensitizes the unreacted explosive column. The failure of detonation propagation occurs as a result. It was concluded in our previous work that reducing PAS velocity was one of the effective methods for the prevention of channel effect.

Jan 1, 2003

By Dave Proudfoot, Mike van Wyk

"There has akvays been plenty of discussion around the ‘accuracy of pyrotechnic detonators withmost recognised manufacturers claiming a variability of arourid 1% or less for their ‘superaccurate’ pyrotechnic based detonators. It is only now being understood that this 1% variabilitycan have serious adverse effects on blast performance. For example a 1% accurate 500millisecond shock tube detonator can fire anywhere between 485ms and 515ms. When wecouple these rather inaccurate ‘accurate’ detonators with short delays on surface, such as a 17millisecond connector, the probability of delay crowding and even out of sequence firing is quitehigh."

Jan 1, 1998

By B. M. P. Pingua & Md. Nabiullah

About 60 to 70 percent of bulk explosives are used in Indian coalmines to achieve coal production for power generation. Coal India Limited (CIL) is the major coal producing company in India. The average production of CIL is 400 to 450 million tonne coal per annum. The major subsidiaries of CIL are Northern Coalfields Ltd., Mahanadi Coalfields Ltd., Bharat Coking Coal Ltd., Eastern Coalfields Ltd, South Eastern Coalfields Ltd. and Western Coalfields Ltd. Most of the mines of CIL have watery holes. Therefore, high water resistance bulk explosives are preferred for better out puts.

Jan 1, 2008

By Jennifer P. Harrell, D. Joseph Hagerty

In many areas of the eastern United States, especially in the Midwest, past mining activities have left large and extensive underground openings. Now, renewed mining is occurring in such areas in surface pits. Also, construction blasting often occurs in rock over such old openings. Within the last fifteen years, some attention has been given to the interaction between surface blasting and underground cavities; concern has been expressed about the possible changes in vibrations transmitted through areas underlain by old mine workings (Siskind, Stachura and Nutting 1987). Previous studies also had indicated that underground openings could influence transmission of surface mine blast vibrations (see, for example, Woodward-Clyde Consultants 1977). The principal concern is that underground openings under surface blasting may intensify low-frequency vibrations. If such intensification occurs, use of available equations to predict peak particle velocities and to design blasting patterns and select blasting parameters could lead to possibly damaging ground shaking.

Jan 1, 2002