Search Documents

It is a case study of huge rock-mass, loosened out from the parent rock-body, & posing a potential danger to structures down below the slope on which this rock mass was standing. Case was dealt in two phases, by tying/stitching the rock mass to the parent rockbody and breaking it using controlled blasting technique.

Jan 1, 1997

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By E E. Cloete, R I. McCrindle

Permitted explosives were previously nitroglycerine based and cap sensitive. Due to safety, health and environmental requirements, water-containing explosives, such as watergels and emulsions, were used instead. However, in order for these explosives to perform at their designed level during blasting, a more powerful stimulus than is delivered by detonators on their own is required.

Jan 1, 1999

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Shao Li, Chen Zhiming, Wu Jihong

In this paper,powder emulsion explosives,which have high sensitivity and strong detonation force,have been studied by applying emulsion technology to the production of the present powder ones.Under the condition of #8 industrial detonator initiation,the distance of air gap propagation is 110~180mm,brisance !3.5mm, lead block test value 325ml and detonation velocity 3000~4000m/s for small diameter (35mm) explosive cartridges.In addition to these,the factors effect on are investigated by experimental study and theoretical analysis.

Jan 1, 1991

By Adrian Moore, Alan Richards

Time window techniques that limit the explosive charge mass being fired within a specified time window (commonly 8 milliseconds (ms)) have been used for many years and are widely accepted by explosives engineers. The 8 ms time window may be relevant for controlling ground vibration for small blasts at close quarters in a high frequency vibration environment. For controlling ground vibration from blasts in a low frequency vibration environment an 8 ms separation between blastholes is arbitrary and meaningless. The 8 ms time window was never intended as a means of controlling airblast. The use of time window techniques will, in many instances, result in airblast and ground vibration levels that are substantially greater than planned, with unfortunate outcomes. The uses of time windows that are inappropriate have been well explained in previous papers. This paper gives further examples of blast designs that satisfied time window considerations but have resulted in substantially greater airblast and ground vibration levels in certain directions, due to wavefront reinforcement or the combined effect of drilling pattern and delay sequence. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid blast vibration problems that result from inappropriate time window techniques.

Jan 1, 2002

By Jeff Wachendorf

Due to the competitive nature of the coal industry we are constantly challenged to reduce costs associated with day to day operations. Every facet of the mining operation is scrutinized for cost reduction and possible efficiency increases. This paper will discuss the pros and cons of two different blasting methods. Buffer blasting has been an institution for many years at Spring Creek Coal and very successful in its application. Cast blasting arrived on a trial basis in 1998 and has produced very encouraging results. This paper will describe the design, drilling, and blasting methods currently used, and a comparison of these two methods.

Jan 1, 2001

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation. The authors worked with three underground metals mining operations to collect surface blast vibration data produced by heading blasts and stope blasts. The data included blast vibration amplitude values, seismograph records, blast design geometry, charge weights, and detonator delay and sequence designs. The total amount of information was used to produce a regression equation and summary dataset that could be used by the proposed underground mining operation to evaluate blast vibration amplitudes that will be generated on the surface. This work is published and presented so that operations with proposed underground mines or proposed underground mine extensions can use these equations to predict vibration amplitudes on the surface above the mine workings before any blasting occurs.

By D T. Froedge

A new system for acquiring blast vibration data and a method for presenting that data in such a way that there can be an extraordinarily enhanced insight into the understanding of vibrations produced by blasting is described in this paper.

Jan 1, 1989

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By Stanley J. Vitton

An important factor to consider during blast damage investigations is whether the structure was constructed on collapsible soils. Traditionally, these soils have been considered to be soils such as loess deposits, which occur along the Mississippi River in locations such as Vicksburg, MS. However, recent research into collapsible soils has indicated that a number of soils may also fall into this category. A collapsible soil is any soil that is susceptible to large decreases in bulk volume upon saturation.

Jan 1, 1997

By Janice Reed

The first seismograph was developed around 132 AD. Much has happened since then. The “modern” seismograph (> 1920) has seen a lot of changes. From falling pin seismographs to magnetic tape units to today’s Z-curve analysis models, the blasting seismograph remains a necessary and useful tool to the blasting community. But why so many changes? What forces drive the advancement of the seismograph? There are many answers and aspects to this question. Research, regulation, and technological advances are the primary forces behind innovation in our industry. But these three forces also drive each other. Research drove our industry from displacement seismographs to particle velocity seismographs. Technology took us from 80 pound seismographs to units weighing less than 5 pounds. Regulation (and litigation) - the driving forces behind the Z-curve analysis units. How have these innovations helped today’s blaster? Have there been any negatives? It is important for today’s blaster to understand how we got here and why.

Jan 1, 2005

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Pierre-Alexandre Abeel, Charles Dowding, Justin Lueker

When blasting is eliminated as a cause of cosmetic cracking, often someone will ask, “If blasting didn’t cause the crack, then what did?” This paper describes detection by remotely operated instrumentation of the new cosmetic crack that was climatologically-induced. The measurement was obtained as a part of the development of Autonomous Crack Measurement (ACM) instruments to measure micro-inch response of cracks to both long-term, climatological, and dynamic, blast vibration effects. The crack occurred in the wall of a structure that was monitored for over 29 months and as such represents one of the longest periods of ACM observation.

Jan 1, 2015

By Tapan Goswami, Geoff Keith

"At Bulga Coal, the objectives of drilling and blasting are to maximise safety and to minimise the totalcost of mining. A recent audit of two overburden blasts established that the standard of drilling and blasting is excellent. No apparent hazards were identified. Laser profiling showed that highwall free faces are reasonably planar with some exceptions, thereby promoting uniform burden distances along front-row charges. However, in three isolated areas along one face, small burden distances existed. The mean and the standard deviation of errors in the collar positions of front-row blastholes was found to be 0.3 + 0.03 m. A borehole video camera was used to show that blastholes did not feature open bedding plane partings, cavities or damage produced by the blast in front of them."

Jan 1, 1999

By Abdel Rahman, M. Khaled, Abo Makarem

There are four large limestone quarries, located nearby Cairo metropolitan. Drilling and blasting operations are used to extract limestone for the cement industries. In these quarries, the blast vibration should be kept below a certain limit. One of these quarries is Tourah Portland Cement Company (TPCC) limestone quarry which, lies near important and historical large caves, within Tourah Mountain. Therefore, control of blast vibration level becomes very critical.

Jan 1, 2007

By F. Malek

An extensive blast monitoring program has been carried out to study explosive performance and the effectiveness of blast designs in production blasts in a deep underground mine. Comprehensive monitoring of blasting vibrations through multi-station high-capacity high-frequency accelerometers, and borehole deformation history have been the main tools of such analysis. The mining activity involves relatively unstressed stopes as well as highly stressed stopes. More than 30 production blasts have been monitored, and the respective vibrations from close-range as well as distant seismic stations have been analyzed, and the vibration parameters (amplitude and frequency) have been correlated with explosive charge weight in the holes. It is found that the correlation between blasting rounds and the corresponding vibration amplitudes often have poor correlation for a very significant portion of the blasts. These point to either explosive charge malfunction in those specific blast holes, or inadequate blast design, or the effect of high in-situ stresses, or any combination thereof. This paper analyzes these variables and their effect on the overall blasting operation at the mine.

Jan 1, 2013

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008

Tracer blasting is commonly used in Canadian underground mines for overbreak control. It involves tracing a column of ANFO with a low strength detonating cord. In order to investigate the effectiveness of tracer blasting in perimeter control and to understand its mechanism, a field experimentation was conducted which involved drifting, benching and pipe tests.

Jan 1, 1994