Search Documents

By John F. Vynne

This paper will discuss the application of available monitoring technology on blasthole drills with the goal being to reduce costs and increase productivity. Case studies from the monitoring of blasthole drills in North American open pit mines will be used to illustrate the ability to meet these objectives.

Jan 1, 1997

By James Ballard, Charles H. Dowding

Recent Office of Surface Mining regulations have called for pre-blast surveys of residences within one-half mile of blasting. Unless lighting effects and the multiple origins of cracks are recognized, hurried (lowest bid price) pre-blast surveys may be more harmful than beneficial. Unrecorded, but pre-existent, cracks can be noticed by homeowners during blasting under special lighting conditions. This paper discusses important factors to note during pre-blast surveys, presents data collection forms and discusses the importance of photographic technique in recording cracks (both present and previously patched).

Jan 1, 1979

By Kurt B. Oakes, Brian M. Fortelka

Unimin Corporation operates an underground Silica Sand mine at Guion, AR located in North Central Arkansas. The Silica Sand deposit at Guion is part of the St. Peter Sandstone Formation, which is overlain by a competent dolomitic limestone from the Joachim formation, acting as the roof directly above. Both the St. Peter and the Joachirn Formations are of Middle Ordovician age.

Jan 1, 1999

By Joseph L. Uraco, Harry C. Verakis

The use of explosives in underground coal mines presents a potential risk for serious injuries and death to miners. Widespread disasters have occurred from the explosion of methane and/or coal dust initiated by blasting with explosives. Many of these disasters took place in the early 1900's when the use of black powder for blasting was prevalent. Historically, the investigations in the U.S.A. to develop and test safer explosives for blasting coal began in 1908 when a testing station was established in Pittsburgh, Pennsylvania. Since that time, great strides have been taken in the development of safer explosives. The use of safer explosives has significantly reduced blasting accidents in coal mines. Enactment of legislation, such as the Federal Coal Mine Health and Safety Act of 1969 and enforcement of regulations has also improved blasting safety. More recently, MSHA began a major revision of its regulations for blasting in coal mines. In 1988, MSHA published final rules for the approval and use of permissible explosives in coal mines. The approval requirements for explosives address testing and evaluation. The requirements include tests for sheathed explosives which represent a new technology. The use regulations provide increased safety protection for miners by including standards to address identified hazards. Major aspects of these standards, such as qualifications for blasters, multiple-shot blasting and the use of sheathed explosives are discussed.

Jan 1, 1992

By W. Reisz

Dealing with misfires can be one of the most difficult and serious issues that blasters must confront. Most of us will - at some point, have to deal with a misfire situation.

Jan 1, 2009

By Qingshou Chen, Paul N. Worsey

It has been recently argued that rock strength has little effect on the final results of pre-split blasting and is of only minor importance when blasting rock in general. However, it can be shown that the maximum borehole separation for optimal perimeter blasting results with constant borehole and loading configuration is strongly dependent on the tensile strength of the rock.

Jan 1, 1986

By BernardThierry

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts. This new type of model enables us to concurrently simulate the fragmentation of the rock, its movement and the associated seismic levels, all within a few minutes, which is a time compatible with a production cycle. Due to the complexity of the model, this article reveals the main principles and compares the results of simulations with on-site measurements in various sectors, i.e. quarries, mines and tunnels.

By H. S. Venkatesh, G. Gopinath, R. Balachander, G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method.

Feb 1, 2020

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Rob Farnfield, Mike Kelly, Toby White

There are a variety of sources of dynamic stress which can affect a building and give rise to cracking. A two-storey house, situated in the middle of a surface coal mine was monitored for a period of 30 months to attempt to identify the major causes of cracking. The factors described as environmental include internal and external temperature, humidity, wind speed and direction, rainfall and water table level. These were monitored using a weather station and piezometer and recorded every 20 minutes. The other factors are vibratory and include normal household movement (walking, shutting doors etc.), vehicle vibration and blast vibration. All the significant vibrations in the house were recorded using four sets of velocity transducers and accelerometers.

Jan 1, 1993

By Conny Postupack, Jim Petrunyak, John Hope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four xchods o f reclsnacisn now in use are reviewed, and their advantages and disadvanrages a r e nocea. Guidelines for seleccrng a particular method are offered in terms of applicability under varying geologic, economic, and technological condirions.

Jan 1, 1989

By Hairong Zeng, Shahram Tafazoli, Edmond Chow

Blast fragmentation is one of the main parameters for optimizing mineral processing, but reliable data is difficult to acquire, resulting in unpredictable performance and efficiency. Crusher and grinder circuits are designed to process specific rock size ranges. Oversized rocks require extra energy to reduce before feeding into the process, and undersized rocks indicate that the process is not used to its full extent. Blast design is the key to controlling the blast fragmentation, so the ability to accurately monitor the particle sizes is imperative.

Jan 1, 2011

By Paul Worsey, Robert Sickler

Today, America's mining and construction industries are faced with operating under a condition of reduced profit margins. This makes the implementation of new technology far more sensitive to investment return than ever before. For this reason it is imperative that every effort be made to insure that new equipment and processes be designed to maximize their impact on improved quality, reduction in production cost and enhancement of safety. Using these principles as a foundation, a study was made to evaluate potential automation techniques for the blasting industry.

Jan 1, 1987

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By Jonathan D. Aubertin

The unique nature of rock salt blasting is compared to traditional hard rock practices. Rock salt geomechanical nature is discussed in the context of rock blasting events. A cratering mechanism prevalent in soft rocks is presented and exemplified through a series of single hole blast tests performed in salt deposits.

Feb 1, 2020

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008