Search Documents

By Stephen C. Tadolini, Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hardrock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Floyd D. Varley, C. M. K. Boldt

Toolbox training is often described as short, informal training conducted at a worksite by technically competent persons for the benefit of a work team. The key feature of toolbox training is the focus on a work team and what is important to that group in its workplace. Toolbox training conducted by peers can connect miners and establish the feeling that the hazard is a real threat to them. This feeling can bridge the gap between delivery of a safety message and behavioral changes that can prevent an accident. Toolbox training is a popular form of "maintenance" training that should not be used to teach a new skill. The 10- or 15-minute toolbox session is simply too short a time to teach or learn a new skill and test for skill development. However, the toolbox format is an excellent way to inform workers of changes in workplace rules, conditions, or hazards by bringing the discussion of change to the level of the work group and suggesting how a change will affect the way workers perform their jobs. Toolbox training should be structured to address a very specific hazard. That is, the hazard source should be identified and the effect of the hazard on the worker described. The temptation to discuss a safety subject in broad terms will result in an equally vague result. For instance, discussing "equipment guards" is inappropriate for a 15-minute training session. There simply is not enough time to cover all the hazards and their remedies. A more appropriate topic would be "placing guards on a conveyor return roller" or "hazards of cleaning a conveyor return roller." Each topic is concise enough to allow the trainer time to define a particular threat to the safety of miners and discuss ways to defend against that threat. The clearest way to a safe workplace is to identify hazards methodically and eliminate them. This cannot be done with sweeping, generalized training. Some best practices that will protect a worker from the hazard should be presented, and the hazard should be located at the specific worksite. Toolbox training is an opportunity for the work team to participate in learning and share experiences and knowledge, often through storytelling. Storytelling is an ancient form of passing along information in an entertaining way. It is entertaining because it draws the listener in with imagination and creativity. Stories told within work groups are a way for miners to exchange experiences in which they made mistakes that resulted in an accident or a near-miss and learned a valuable lesson. Thus, co-workers can learn from others without the pain or fear that accompanied the storyteller's learning path. To encourage these shared experiences, the people in the group must be comfortable with one another. Participation doesn't stop with listening to a near-miss story or informing the group of an unsafe work practice. Participation by sharing experiences, knowledge, and skills should lead toward action in changing the unsafe tool, practice, or machine (Wallerstein, 1992). This power to change is called empowerment. Empowered workers use toolbox training sessions to discuss a problem; direct their own knowledge, experience, and talents in the context of their work environment to solve the problem; and put into practice what they have learned by sharing (Baker, 1992). A worker is much more likely to implement changes they have contributed to creating than changes forced upon them. Toolbox training functions best when the group size is small (under 20) and composed of workers with similar job functions. While combining all workers on a shift or multiple shifts may be convenient, the level of participation will drop dramatically as group size increases and participants are less connected. Similarly, when the work group participants are from different job functions, keeping the materials relevant to the individual becomes more difficult. The role of management in the toolbox training system is to communicate among various groups so that all groups at a mine site are hearing the same message. In very small operations, combining work groups can be productive if the trainer can promote open discussions and lead the group to solutions that address the needs of all and not let one group or individual dominate the discussion. WHY USE NARRATIVE METHODS An effective communications tool is to use stories as a means of describing a hazard and its consequences. Historically, using stories to transfer knowledge between individuals of the same and different generations is well established. All good stories share the same elements required to communicate safety principles. Stories require a setting (the part of the workplace), a plot (the circumstances that lead to a hazard), the solution (best practices), the lesson (what can happen), and the result (what will be done to prevent the hazard) (Dennehy, 1999).

Jan 1, 2002

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Pedro Lilienfeld

This Final Report describes a program whose objective was to design, develop, fabricate, and test an airborne mass monitor for unattended and recording measurements of the concentration of dust in mining environments. Sensing collection are performed by beta-radiation attenuation and inertial implementation respectively. The instrument is portable, battery or line operated provides a digital printout of the mass concentration during each selection sampling period, as well as the accumulated mass of dust, and the elapsed sampling time.

Jan 1, 1974

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

By A. J. Farstad

The principle objective of the research effort described herein was to identify as rapidly as possible a practical trapped miner location system. Much effort has been expended in the past on the development of a highly sophisticated seismic location system [1] for trapped miners. Field tests of this system have shown that the location accuracy is limited by a combination of seismic velocity anomalies, timing errors, and in general by the relatively weak nature of the signals received at the surface. It was first felt that similar propagation anomalies would be experienced by electromagnetic systems, but to a greater extent than the seismic. However, preliminary tests performed by Westinghouse on the Operations and Maintenance Program, Contract No. H0210063 in 1971 and 1972, indicated that an electromagnetic solution to the location problem may be more feasible than a seismic solution. Thus a more concentrated effort was launched in 1972 and 1973 to more completely determine the feasibility of electromagnetic location systems for trapped miners. Two different approaches to the location problem were undertaken on this program: (1) A pulsed electromagnetic system was developed by the Special Systems Division of Westinghouse in Baltimore, and (2) a Continuous Wave (CW) System was developed by Westinghouse Georesearch Laboratory (WGL) in Boulder, Colorado. Part I of this report will deal only with the development and results of CW Location System developed by WGL. The CW Location System was field tested at three eastern coal mines and at one western hardrock mine. The maximum overburden depth penetrated during these tests was 990 feet at the Robena No. 4 mine near Waynesburg, Pennsylvania. The earth conductivity at this mine was measured to be 1. 1X102 mhos/m, which combined with the deep overburden make this mine representative of expected worst case conditions for a coal mine EM location exercise.

Jan 1, 1973

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile coal in the usual type of byproduct-coke oven, because they expand excessively and exert side thrust, which ruins the oven walls. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking, coals with as much low-volatile coal as possible and still have a mixture that will not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile coal has been exceeded and ovens have been damaged. It is desirable, therefore, to rave a reliable method of determining the expanding tendencies of mixtures before they are charged into the ovens. Furthermore, coal charges somewhat in its properties as mining progresses, and therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used.]

Jan 1, 1938

By John W. Taber

"INTRODUCTION AND SUMMARYDiscovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits, appear to be sharp-walled, low-angle, tabular ore bodies in granite and are at least 10 feet thick.The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaFp and 1.44 percent SiO2.Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3."

Oct 1, 1952

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. Tile abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources:

Jan 1, 1963

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By Valois R. Shea-Albin

Ground control problems are an important factor affecting safety, production, and efficiency in underground coal mines. A major portion of ground control problems encountered in underground coal mines can be attributed to geologic features in the strata surrounding the extracted coal seam. The U.S. Bureau of Mines has compiled information from numerous sources on the geological features that contribute to ground control problems in underground coal mines. The compilation includes (1) sedimentary features such as paleochannels, crevasse splays, clastic dikes, mold-and-cast structures, concretions, and lithologic factors, and (2) structural features such as folds, fractures, joints, cleat, and faults. The compiled information will aid in identifying the features, predicting their occurrence in advance of mining, and controlling or minimizing roof failure when these features are encountered in an underground coal mine.

Jan 1, 1993

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936 and their rapid development have brought tine problem of brine disposal to the foreground in that State. The ultimate magnitude of the is not yet known, but already it is great enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field brines in Illinois and has studied in detail three subsurfaces disposal systems.]

Jan 1, 1940

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Marshall County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, were estimated at 3,158 million short tons as of January I, 1954. Of this total, 3,071 million short tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By Eric E. Ungar

Some fundamental facts regarding noise are summarized. Guidelines for reducing plant noise are indicated, and simple means are discussed for determining, whether quieting of specific equipment items will reduce plant noise significantly. Design and installation recommendations are made for quieting chutes by means of dams, impact cushioning pads, impact shields, and damping materials, and for quieting; screens by means of resilient decks, lined screen bottoms, drive mechanism enclosures, and side plate additions. A brief account is appended of the wear and productivity performance of resilient materials observed in three cleaning plants.

Jan 1, 1976

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990