Search Documents

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By C. B. Manula

Simulation continues to hold the spotlight among the Operations Research applications in the operational side of mining. One reason for this is the need to solve the many waiting line and storage problems common to the industry. A second reason for using simulation is the central requirement of retrospect testing. Acceptance of a model by management is more likely to depend on its tested performance rather than on the underlying validity aspects of the model itself. Mathematics have not been and may not be developed that will allow all desired system elements to be considered simultaneously. It is in this realm that simulation bridges the gap between theory and useful design procedures. One of the earliest published accounts of simulation at work in the coal industry is demonstrated by the application cf Monte Carlo methods to explore changes in future operating policies for an existing track system (Manula, 1963). By modifying certain control parameters, revision in design changes were evaluated in the computer rather than in the actual production section. A second application which has found wide use in practice is the VFI-OCR Face Simulator (Prelaz et al., 1968). The model developed here has the purpose of allowing the comparison of methods for room-and-pillar face operations end observing their effect on mining prior to actual installation. Proposed changes are tried in the model and the best of these are selected as a guide for better mire management: IBM's own simulation package, the System 360 General Purpose Simulator, has experienced heavy use in solving similar problems and other steady-state situations.

Jan 1, 1974

By R. L. Marovelli

ANTICIPATING the eventual use of the huge tonnages of nonmagnetic taconites of the Mesabi range of the United States, the Federal Bureau of Mines is classifying and evaluating these deposits in detail. This introductory report describes work begun in 1954 as part of a long-range program to sample, classify, and evaluate important occurrences of nonmagnetic taconite on the Mesabi, range. Included in this report are brief discussions of the geology, history, and potential of the Mesabi range district and mining industry, together with a more detailed presentation of the sampling and metallurgical evaluation of these nonmagnetic taconite deposits. A total of 898 field samples was collected. Most of these were taken in the region between Grand Rapids and Chisholm, Minn., but a few came from the area between Chisholm and Buhl, Minn. Of the total samples, 865 were from open pit bank faces where the greater vertical distances presented by the cherty members facilitated the taking of a large number of samples. Conversely, the narrow face presented by the slaty members confined and limited the areas from which samples were taken. In addition, 33 of the field samples were taken from rock dumps in order to determine, in a preliminary way, the characteristics of these materials.

Jan 1, 1961

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

This report is the 25th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations, and the 7th of these reports to be issued on a calendar-year basis.3 It reviews briefly work in progress during 1960, and furnishes references to publications by Bureau personnel during 1960 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned can be found by referring to the publications cited in the footnotes or in the further list in the Miscellaneous section; other phases of work are reported here for the first time and will be covered in more detail by later publications, Coal programs of the Bureau of Mines extend over the wide range of theoretical and applied studies indicated by the table of contents. Fundamental research on coal structure and on the properties of coal will, over a period of time, increase the general knowledge about coal Which scientists and engineers may use in answering practical questions and in solving problems in the mining and utilization of coal. More applied studies are conducted in connection with the developement and evaluation of new mining techniques and the effective processing and utilization of coal and of coal products. Health and safety activities, analyses of coal being mined, and technical advice and assistance to Federal agencies in connection with fuel and boiler-water problems are among the practical services handled by the Bureau.4 5

Jan 1, 1962

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By Felipe Calizaya

This study describes the principles involved in the design of a booster fan installation, the basic requirements, and the provisions needed to guarantee a safe operation of the unit. It also describes how a booster fan should be selected and what measures should be taken so that events such as uncontrolled recirculation of air in a mine can be avoided. A computer program called MFSELECT is presented to assist the ventilation engineer in the design process a For a given mine ventilation network, the program determines the duties of fans and regulators that will fulfill the airflow requirements of a mine and minimize the total power consumption. The application of the program is illustrated by the detailed solution of a sample problem. A Case Study based on the Jim Walter Resources' No. 7 Mine is utilized to describe the basic requirements for the design and operation of booster fans, and illustrate their potential benefits in mine ventilation. Finally, the study discusses a process control system designed to evaluate the safety conditions in the mine and report on the status of both surface fans and underground booster fans.

Jan 1, 1990

By H. J. Coleman

Knowledge of the types of naturally occurring sulfur compounds in petroleum is of both theoretical and practical interest to petroleum chemists and geologists. This knowledge has been extended by the identification of 77 sulfur compounds, including 36 thiols, 23 chain sulfides, and 18 cyclic sulfides in a 111° to 150° C boiling range distillate of Wasson, Texas, crude oil. The characterization procedure used in separating and identifying these compounds included isothermal distillation, vacuum fractionation, liquid-solid chromatography (alumina adsorption), chemical treatment, gas-liquid chromatography, microdesulfurization, and infrared analysis. The procedural steps described represent a systematic method of sulfur compound analysis considered applicable for determining the nature and concentration of the sulfur constituents present in any straight-run petroleum distillate of the above-boiling range.

Jan 1, 1966

By J. B. Carman

This paper, describing the concentrator of the Molybdenum Corporation of America in Taos County, northern New Mexico. 7 miles east of Questa, is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. The mine from which the ore comes is 1 1/4 miles from the mill, and produces about 40 tons of ore per day by the cut-and-fill method.3 The ore contains about 5 per cent of MoS2. The mill has a capacity of 50 tons of ore per day and utilizes flotation methods. Water is taken from Red River. Power is generated by a water wheel, or by a Diesel engine in times of water shortage during the winter. The mill is located close to the bottom of a canyon, in order to obtain maximum head or, the water wheel, and the flow of ore is therefore maintained partly by gravity and partly by an elevator and pumps. ORE TREATED The MoS2 content of the concentrator feed ranges from 4.5 to 7.5 biotite, fluorite, small amounts of rhodochrosite and calcite, and the minerals of the granodiorite country rock.

Jan 1, 1932

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By Jeff Kravitz, John Kovac, Wayne Duerr

Since 198 1, Federal mining law has required every miner working in underground coal mines to have a self-contained, self-rescuer (SCSR) available for use in emergencies. Some miners that have escaped from fires using SCSR's have reported that they had to remove their mouthpiece to talk during escape, thus compromising the protection afforded by the SCSR. If miners are in thick smoke during an escape, they may have trouble if they become separated from their group. The visibility can be so poor that separation can occur at very short distances. To address this problem, two-way, FM radios were built into the SCSR to improve the ability to communicate should the miners be separated over relatively short distances. The SCSR prototypes built and used in testing included both two-way radios and improved mouthpieces. Comparison studies were conducted using combinations of the new and old mouthpieces, and trials using the radio or not using the radio. Subjective judgments indicate that communication ability was significantly improved using the prototype devices. Communication problems have been encountered with teams using standard voice- powered communications systems. Mine rescue teams perform rescue and recovery work under extremely hazardous conditions, life lines are a standard part of mine rescue team equipment. Leaky feeder and quasi-leaky feeder life line communications systems provide significant improvements over standard systems. These improved systems allow all members of the team to communicate with each other and their base of operations. These innovations will significantly enhance the safety of mine rescue operations.

By Richard A. Dick

This Bureau of Mines report describes the evolution of modern-day blasting agent and slurry products and the state of the art of the usage of these products as it exists today. The steadily increasing consumption of blasting agents and slurries at the expense of cartridged high-explosive usage is related. Although safety is not covered in depth, reference is made to pertinent safety literature available. Product formulations, detonation reactions, and detonation products are discussed. Product terminology is defined and the significant differences between the relatively insensitive modern-day dry blasting agents and slurries and cap-sensitive high explosives are described. Blasting agent and slurry properties are discussed, as well as methods of determining and describing these properties, and specific types of products are also discussed with reference to their ingredients,-properties, and field applications. Increasing consumption of slurries, particularly in small-diameter boreholes, and the development of more cap-sensitive varieties of slurries are forecast although dry blasting agents should continue to dominate the market. The consumption of cartridged high explosives will level off or gradually decrease.

Jan 1, 1972

By S. Peterson, E. C. Westman, P. L. Swanson

Coal bumps are brittle, violent failures associated with high stresses and competent host strata. To study bump mechanisms, conditions in the vicinity of a deep longwall mining face in bump-prone strata were monitored using three discrete systems. First, a microseismic monitoring network recorded mining-induced seismic events throughout the mine and surrounding strata. Second, pressure variations and distributions on the longwall shield legs across the face were recorded. Last, tomography surveys imaged seismic transmission properties ahead of the face. Results from the three systems were correlated in an effort to increase understanding of mining-induced stress redistribution and bump potential. An initial, one-week study showed that the correlation between averaged tomogram values and seismically active areas had a coefficient of correlation (R) of 0.89. Further results of these studies demonstrate that the tomography system is capable of imaging heavy shield-leg loading and bump-prone conditions prior to them disrupting the face operations.