Search Documents

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United Status. These data are presented in tabular form under the following headings; General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

By Sidney Katell

The present report, a continuation of the series of Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, is concerned with articles published from January 1958 through December 1958. The periods covered in previous reports are as follows: January 1930 - August 1948 I. C. 7516 September 1948 - June 1952 I. C. 7705 July 1952 - June 1954 1. C. 7751 July 1954 - December 1956 I. C. 7847 January 1957 - December 1957 I. C. The following sources were used to obtain the references to and the abstracts of the published articles included in this report: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Coal Age. 6. Coal Utilization. 7. Cost Engineering. 8. Industrial and Engineering Chemistry. 9. Nucleonics. 10. Oil and Gas Journal. 11. Petroleum Engineering. 12. Petroleum Refiner. 13. World Oil.

Jan 1, 1959

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By E. P. Youngman

The basic mining law of Esthonia is the law that was passed by the Parliament (Riigikogu), or State Assembly, on March 17, 1927 (effective Avril 1, 1927), superseding the Russian Mining Law Book VII of the Code) issued in 1912. References in this digest are only to articles of the Law of Merch 17, 1927. However, the law concerning all industrial enterprises (Riigi Teataja No. 28, 1920, Law No. 106) governs not only mills and refineries but also mining operations themselves (arts. 2 and 3). No access was ad to that law. Esthonia is not well supplied with minerals; its industries are primari- ly agriculture and dairy farming. Natural gas, prites, lead, zinc, iron ore, salt, and mineral waters have been found but never as yet in deposits of commer cial size. The production of oil shale is of some importance; and peat, which covers as much as 5 per cent of the total area of the country, is mined in sub- stantial quantities. Cement rock, gypsum, fire clay, and phosphate rock likewise are produced, though only on a small scale.

May 1, 1930

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978-September 30, 1979) under its Mine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By Curt D. Edgerton

This study was made to determine trends in fresh water usage by California petroleum refineries, to forecast fresh water requirements to 1975, and to evaluate water conservation practices. Statistical data used in the study were obtained largely from published sources and from records of selected companies. An adequate sampling of the State's refining capacity was obtained, and the data were extrapolated to the total California refining capacity. A breakdown of the data was then made on the basis of the following refining regions: (1) the Los Angeles Basin and Southern Coastal region, (2) the Southern San Joaquin Valley, and (3) the San Francisco Bay area. An unpublished forecast of crude oil input to refineries by a major oil company operating on the West Coast was used as a basis for predicting fresh-water usage. The 1963 fresh water intake by California petroleum refineries was 84 million gallons per day. This is expected to increase to 128 million gallons per day by 1975. The fresh-water to crude-oil ratio is increasing in all regions except the Southern San Joaquin Valley. At present, the supply of fresh water available to almost all of the State's petroleum refineries, mostly from surface sources and company-owned wells, is adequate, although shortages may develop within the foreseeable future. Present conservation methods are centered around the following four objectives: (1) minimum intake of fresh water of the lowest possible quality commensurate with sound technologic practice; (2) optimum recirculation; (3) proper treatment before discharge; and (4) substitution of air cooling for water cooling.

Jan 1, 1965

The applicability of borehole assaying techniques, both conventional and advanced, to orebody evaluation in the mining industry is reviewed and assessed, and the research, development, and demonstration programs necessary to apply the various logging techniques to mining are outlined. At present, the principal method of orebody evaluation in the mining industry is coring. However, coring is costly and time-consuming, and potentially great savings can be realized if all or part of d coring program is replaced by a borehole logging suite specialized to the needs of the particular mining industry. Using a set of 12 minerals, most of which are essential to the U. S. economy, an algorithm is presented for calculating the priority of developing suitable borehole assaying technology to replace all or part of the coring in each mineral industry, The priority is expressed in terms of dollars currently spent for that portion of present orebody evaluation techniques which may eventually be replaceable by in-situ assay techniques. The orebody assay requirements (grades, accuracies, etc.) of the 12 selected mineral industries, as determined from mining industry interviews and published literature, are compiled and represent performance criteria for borehole assaying instruments for the particular industry. Current logging techniques, applied chiefly in the petroleum industry, and advanced assay techniques which are or may be packageable for borehole use are evaluated to determine their performance characteristics. The performance characteristics of the various conventional and advanced techniques are then compared with the performance criteria in each of the 12 mineral industries in order to determine the potential benefit derivable from each technique. Finally, the benefit available from each technique, averaged over the 12 mineral industries, is compared with the cost of development of the technique, to determine the overall priority for investment in research to develop the technique for use in mining. The technology assessment and cost-benefit analysis shows neutron activation analysis in its various forms to have the highest priority for research and development as a borehole logging technique. Other techniques found to be promising include x-ray fluorescence, x-ray diffraction, photoluminescence (optical fluorescence), and infrared spectroscopy. Of the 12 industries considered in the study, those where the need for advanced borehole logging technology is greatest are uranium, copper, gold, and iron.

Jan 1, 1976

By R. W. Watson

At the request of the Mine Safety and Health Administration (MSHA) the Bureau of Mines evaluated the potential hazards of three compressed oxygen self-contained self-rescuers (SCSR's) designed for use in under-ground coal mines. The evaluation followed the lines used in a similar investigation of chemical self-rescuers and involved laboratory experiments as well as field trials designed to simulate a mining environment. They included bullet impact, bonfire, feeder-breaker impact and feed-through, and mining machine runover tests. The work showed that the units were not inherently unsafe but that under certain conditions of extreme abuse they can present a potential ignition or explosion hazard. This, coupled with a survey of reported damage on SCSR's currently deployed in underground mines, which indicated a relatively high frequency of incidents leading to the destruc-tion of the units, led to new recommendations on the deployment of SCSR's. The recommendations formulated by MSHA state that the units should be either properly worn by the miner, stored in heavy containers, or otherwise protected from situations in which they might be accidentally ruptured or destroyed, such as runover by mobile mining equipment.

Jan 1, 1984

By Robert W. Geehan

"INTRODUCTION The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Many of the mines were developed.A preliminary examination of the Sultan mine was made in January 1945 by the author, who recommended investigation by drifting and crosscutting. The Bureau conducted a project at the mine from April to June 1946. Claims investigated are in sec. 20, T. 25 S., R. 58E., Mount Diablo base and meridian, in southern Clark County, Nev., about 7 miles southwest of Good-springs.The Sultan mine has been an intermittent producer of zinc-lead-silver ore since 1910. During World War II, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting& Refining Co.'s smelter near Salt Lake City, Utah. Throughout the past year, ore has been milled and the concentrates have been shipped to the smelter."

Sep 1, 1947

By Curt D. Jr. Edgerton

This study was made to determine trends in fresh water usage by California petroleum refineries, to Forecast fresh water requirements to 1975, and to evaluate water conservation practices. Statistical data used in the study were obtained largely from published sources and from records of selected companies. An adequate sampling of the State's refining capacity was obtained, and the data were extrapolated to the total California refining capacity. A breakdown of the data was then made on the basis of the following refining regions: (1) the Los Angeles Basin and Southern Coastal region, (2) the Southern San Joaquin Valley, and (3) the San Francisco Bay area. An unpublished forecast of crude oil input to refineries by a major oil company operating on the West Coast was used as a basis for predicting fresh-water usage. The 1963 fresh water intake by California petroleum refineries was 84 million gallons per day. This is expected to increase to 128 million gallons per day by 1975. The fresh-water to crude-oil ratio is increasing in all regions except the Southern San Joaquin Valley. At present, the supply of fresh water available to almost all of the State's petroleum refineries, mostly from surface sources and company-owned wells, is adequate, although shortages may develop within the foreseeable future. Present conservation methods are centered around the following four objectives: (1) minimum intake of fresh water of the lowest possible quality commensurate with sound technologic practice; (2) optimum recirculation (3) proper treatment before discharge; and (4) substitution of air cooling for water cooling.

Jan 1, 1965

By Howard C. Pettibone

Mine safety personnel reported occurrences of excessive "glove-fingering" and other problems with resin-grouted roof bolt installa tions. To study these problems, the Bureau of Mines designed a test plan to (1) obtain baseline information on several resin cartridges and (2) investigate the variables involved in the installation of a resin bolt. Three brands of resin representative of the industry in January 1983 were selected for cartridge evaluation. The installation variables selected for study were the method of installation, the hole depth, and the hole annulus. These variables were studied by installing a series of bolts in concrete blocks using different values for each variable. Results of the research show overspinning the resin may cause problems, but they can be avoided by using the spin times recommended by manufac-turers. Excessive glove-fingering is not a problem if the manufacturer-recommended installation procedures are followed.

Jan 1, 1987

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

[ ]

Jan 1, 1979

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By R. D. Haynes

Coal, gas, and oil in many geological formations of the Eastern United States are intimately associated but have traditionally been recovered independently of each other. Oil and gas wells, however, are often spaced sufficiently close to cause the subsequent loss of up to 50 percent of the recoverable coal in the form of pillars or barriers left for mine safety purposes. A long-range planning technique was devised for exploiting oil and gas wells simultaneously with the mining of coal to recover the maximum fuel potential of the formations. Planned plugging of oil and gas wells, determined partly from production predictions via decline curve analysis, is coordinated with a mine development plan to achieve maximum coal recovery and reduce overall production losses of gas and oil due to plugging of the wells.

Jan 1, 1973