Search Documents

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

Reduce accidents associated with handling of the electrical trailing cable and the water hose on mining equipment. Approach Two reels were mounted on a loading machine to store and release the lines as required during face operations. How It Works A hydraulic motor, which is actuated by a treadle valve in the operator's cab, controls the reel on which 50 feet of electrical power cable is stored. A spring motor resists unwinding of the other reel on which 50 feet of water hose is stored. Both reels are mounted on the right rear of the loading machine. See Figure 1. Following common mining practice, the cable and hose are anchored to fixed points at the first intersection outby the face. Tramming forward causes the cable and hose to be pulled from the reels. Depressing the treadle valve causes the electric cable reel to turn and wind-in any slack in the cable. The spring tension on the water hose reel automatically rewinds the water hose when the loader is trammed in reverse.

Jan 1, 1978

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973

By W. W. Staley

This paper discusses the design of small head frames that will fill the needs of prospectors and small operators whose operations are conducted through shafts. The head frames considered were designed to handle relatively small tonnages. It was assumed that the shafts in which buckets are used would not exceed 300 feet in depth and that not over 60 tons of rock would be hoisted, in, 14 hours. In the design of the larger head frames, a hoisting capacity of about 250 tons per 6 hours from a depth of 300 to 500 feet was assumed. Under these conditions, hoisting speed, rate of acceleration, and weight of rope have a negligible effect on the head frame design and, therefore, have been ignored in the following, discussion. Because timber is relatively cheap and easily obtained in most mining areas, the discussion has been confined to timber construction.

Jan 1, 1937

By Larry A. Haas

Carbonyl sulfide (COS) was decomposed to sulfur and CO in a silent electrical discharge. A threshold of about 4 kv at 60 Hz was required to dissociate the gas in a laboratory ozonizer at 790 torr with electrode gaps between 1 and 5.5 mm. Above the threshold value, the reaction rate increased with increasing voltage with helium or nitrogen diluent. With the latter diluent, higher voltages had to be applied to obtain the same yield in the 4-to 12-kv range. The COS decomposition rate increased with COS concentration, but a saturation value was reached at about 10 pct COS. The reaction rate decreased at low linear gas velocities as obtained at lower gas flows, larger electrode gaps, or larger reactor volumes. Increasing gas temperature also decreased the decomposition rate. The presence of solid adsorbents such as quartz wool, bauxite, or charcoal had no significant effect on the reaction rate. The addition of S02 did not affect the COS decomposition rate, but small amounts of water decreased the reaction rate. Over 50 pct of the COS was decomposed at room temperature and atmospheric pressure in a l7-kv ozonizer using a gas containing 0.9 pct COS in helium flowing at a rate of 0.3 liter/min. The average current was less than 5 ma. This method has possible application in eliminating the toxic air pollutant, COS, which is generated in petroleum refineries and in processes involving reactions between sulfurous and carbonaceous materials. Carbon monoxide that is formed can be further oxidized to CO2 after the collection of elemental sulfur.

Jan 1, 1972

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

By William O. Vanderburg

Tis paper describing the mining practices at the Cold Springs mine of the Wolf Tongue Lining Co. at Nederland, Colo., is one of a series of similar papers prepared by the Fureau of kines on mining practices, methods, and costs at various mines in the United States. The writer acknowledges the assistance of William Leach and William T. Todd, manager and mine superintendent of the Wolf Tongue Mining Co., respectively, in the preparation of this paper.

Dec 1, 1932

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By Eric E. Cather

In 1984 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines conducted a mineral appraisal of the 315,000-acre Lemhi Range study area. This area is located in Lemhi and Custer Counties, about 25 mi south of Salmon, Idaho, and is in the Northern Rocky Mountain physiographic province, Topography is generally rugged with elevations ranging from 5,600 ft to about 11,350 ft above sea level. Since the 1880's, approximately 500 mining claims have been located within the study area; about 400 were current at the time of this investigation. Also, part or all of 12 patented mining claims are in the study area. During Bureau field work, forty-four mineralized sites were examined. The sites had been explored by 80 adits, 14 shafts, and about 140 pits and trenches. At least five properties in the study area have had significant production; the adjacent Mohawk, Grace Phelan, and Snowbird claims had a combined total of 136,000 oz of silver and 67,000 lb of lead; production at the Brown Bull was about 14,800 oz of silver and 115,000 lb of lead; the Portland mine yielded an unrecorded amount of silver. The Hilltop mine, located a few hundred feet outside the study area, produced 125,000 oz of silver, 2.7 million lb of lead, 87,000 lb of zinc, and 62,000 lb of copper from mineralized zones that might extend into the study area. More than 10,000 lb of copper were produced at the Blue Jay mine from workings located about 1,000 ft outside the study area. The Bureau of Mines investigation did not reveal the presence of identified resources in the study area. However, several areas contain mineralized sites and are known occurrences. Some of these warrant additional work to further delineate the mineralization and possibly determine identified resources.

Jan 1, 1988

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

Provide long-term measurement of mine sidewall closure in backfilled stapes subject to flooding. Approach A water resistant extensometer is made by enclosing a rod-actuated transducer in a telescoping tube which is enclosed within an oil-filled outer housing. How It Works To assemble a water resistant extensometer, a cylinder -shaped transducer and two support rings are pushed into the small-diameter section of the telescoping tube where the transducer is held in place by friction. The outside of the small-diameter section of the telescoping tube is then greased and slid into the slightly larger-diameter section. See drawing. The cylinder-shaped transducer contains a potentiometer whose actuating arm is attached to a stainless steel extension rod that passes through one end of the telescoping tube. A similar rod is attached to the opposite end of the transducer body, and extends through the other end of the telescoping tube. A coil spring inside the large diameter end of the telescoping tube extends the tube

Jan 1, 1978

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By W. M. Traver

As a direct result of the second World War, consumption of nickel in the United States has increased to such an extent that it has been considered timely to investigate undeveloped deposits of the nickel minerals. Funds were made available to the Bureau of lines in 1941 to investigate the extent, occurrence, and quality of nickel ores in the Mirror Harbor area. The Federal Geological Survey mapped' and studied the area during the summer of 1941 and Robert S. Sanford, an engineer of the Bureau of lines, made a preliminary examination in June 1942. A contract for drilling the deposits under the direction of the author was let in July 1942.

Jan 1, 1948

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

By Robert H. Merrill

Several investigators have obtained solutions for the concentration of stress around circular, ovaloidal, elliptical, and rectangular holes in an elastic, isotropic, semiinfinite plate subjected to uniaxial and biaxial stress. These solutions are used to evaluate the changes in stress around openings immediately under the undercut normally used in conventional block caving operations. The evaluations are based on the assumption that a horizontal undercut removes most of the vertical component of a biaxial stress field. The location and magnitude of the significant changes in stress concentration around the opening are computed. Conditions under which the assumptions used in the evaluations may or may not be consistent with conditions around block caving mines are discussed, and examples of preferred opening shapes for a biaxial (hydrostatic) stress field are shown. This report is a summary of one phase of an investigation to establish design methods for the size and shape of mine openings used in block caving mining methods .

Jan 1, 1962

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961