Search Documents

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960

By Edward L. Tullis

Numerous widely distributed pegmatites of the southern Black Hills of South Dakota contain small amounts of beryl, and two minor deposits are known in the northern Black Hills. Few mines have produced more than 50 tons, and the current, rate of production for the area is about 100 tons annually. Total production, since the first records, is 2,358 tons. Most of the deposits contain less than 1 percent beryl, although the beryl zones in several deposits contain 2 percent beryl or more. Estimated reserves of beryl total 11,824 tons, and an additional 234 tons has been measured; there are other unestimated reserves. The pegmatites are in a belt about the margin of the Harney Peak batholith in the southern Black Hills, although they fail into three districts. The most important, from the point of view of production and reserves, is the Keystone district. Many deposits also are found in the vicinity of Custer and Pringle. Small amounts of beryl occur in the dikes near Hill City. A little beryl has been produced from the Tinton district in the northern Black Hills, and an undeveloped dike has been discovered on Whitewood Peak near Deadwood. The beryl-bearing pegmatites are principally coarse-grained intergrowths or massive segregations of feldspar, quartz, and mica. Some of them contain notable amounts of lithium minerals, as well as some tantalite, columbite, and cassiterite.

Jan 1, 1952

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By J. A. Kost

The contract objective was to evaluate the effectiveness of available dust-control technology for double-drum shearers. Eight underground surveys were conducted to evaluate drum design, drum spray nozzle locations, ranging-arm sprays, water quantity, wetting agents, and cutting techniques. The final report is made up of eight dust-control technique reports, each discussing, details of the individual mine surveys.

Jan 1, 1985

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968

By J. P. Capp

The Bureau of Mines conducted field-scale experiments in underground gasification of coal with oxygen-enriched air. A path about 140 feet long was linked at the rate of LO feet per day through a coalbed hydraulically fractured with a mixture of starch gel and sand. During the best gasification period, which extended for 2-1/2 days, 785,000 std. c.f. per day of 124-B.t.u. gas was produced. In other periods the heating value at times was almost 300 B.t.u. per std, c.f,, but sustained production of such gas was not achieved. During gasification, a total of 50 tons of coal was gasified and 114 tons of coal was carbonized. Approximately 12 million B, t .u. per foot of nominal path was recovered at the surface.

Jan 1, 1962

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957

By W. W. Cutler

An oil-field drilling campaign is used in this paper to signify the spacing of the wells to be drilled as well as the drilling program, which is interpreted as the number of wells drilled in a unit of time, This has an important bearing upon the time of receiving income, as well as upon the amount of revenue obtained In periods of low prices for oil, such as the present, the margin of profit is at the best very small, and the correct determination of the drilling campaign may be the deciding factor between incurring financial loss or gain during the depressed period. General policy of the operator. Drilling should be planned by the field engineer to conform with the general policy of the operator. This policy may be one of conservation daring the early life of the property, but as mentioned later, this may result in a smaller ultimate recovery it often occurs that the market price of oil does not warrant rapid development, or it may be desirable to hold in reserve a supply of oil for a refinery. The policy may be to recover all of the oil as quickly as possible, or it may be to maintain a constant and sustained production. In any case, the operator should, outline as far as possible a definite policy, and should understand the principles underlying the recovery of oil, the influence of rapidity of drilling and effects of spacing, in order that he may obtain the oil as required with the least expenditure.

Jan 1, 1921

By B. G. H. Thomas, W. P. Yant, A. C. Fieldner, R. R. Sayers, W. J. McConnell

"One of the outstanding problems confronting automotive engineers in attempting to construct motors of greater economy is that of eliminating the ""knock"" from the operation of the engine. Recent investigations of this detonation or knock in internal-combustion engines, especially of the high-compression type, have demonstrated that it can be eliminated or reduced by decreasing the reaction velocity of combustion by adding small quantities of certain compounds to the gasoline, This makes it possible to use engines of a higher compression ratio, thereby greatly increasing the mileage per gallon of gasoline consumed. The savings in fuel reserves from increasing the proportion of crude oil marketable as motor fuel and in permitting the designing of more efficient engines are obvious.Ethyl gasoline, one of the widely used anti-knock fuels, is ordinary motor gasoline to which has been added 3 c.c. of tetraethyl lead and 2 c.c. of a halogen carrier, as ethylene dibromide or trichiorethylene, or approximately 0.06 per cent of the lead compound and 0.04 per cent of ethylene dibromide by volume. Ethyl gasoline should not be confused with ethyl fluid, which is a mixture of concentrated tetraethyl lead and ethylene dibromide in the prowler proportions for mixing with gasoline, but is not a motor fuel and is not sold to the public. Also tetraethyl lead is not a motor fuel, and likewise is act sold to the public."

Dec 1, 1924

By A. C. Fieldner

[The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according; to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-rank coals according to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.]

Jan 1, 1935

By Avery H. Reed

[The Bureau of rides is making a general study of the occurrence of the Clinton red iron ores of Alabama. In the course of this study, it developed that the iron-ore seams of the Woodstock and Bucksville areas were virtually unexplored., and the nature and extent of the ore deposits were undetermined. As a part of the work of the project, the Bureau investigated the occurrence of red iron ore in the .areas. Eighty-four channel samples, representing 317.6 linear feet, were taken from l2 locations along the outcrop of the red iron-ore seams, Ten diamond-drill holes, amounting to 3915.5 linear feet, were drilled. In these areas, commercial- and marginal-grade ores of minable thickness have been shown. It is estimated that 4,500,000 tons of indicated ore and 6,700,000 tens of inferred commercial-grade ore averaging 5.1 feet thick, 47.6 percent Fe, 26.1 percent insoluble, 0.1 percent CaO, and 0.04 percent P; 7,200,000 tins of inferred marginal grade ore averaging 6.1 feet thick, 36.2 percent Fe, .35.0 percent insoluble, 3.9 percent CaO, and 0.14 percent P; and 18,500,000 tons of ferruginous sandstone averaging 12.2 feet thick, 19.2 percent re, 50.1 percent insoluble, 9.6 percent CaO, and 0.14 percent P are present in the areas.. All tonnages are estimated as gross tons of recoverable ore in place, based' on 65-percent mining recovery. In accordance with established policy of the Bureau of Mines of publishing factual data as soon as possible after completion of field work, this description of the Woodstock and Bucksville areas is presented. As soon as work is completed in other areas additional reports will be prepared.]

Jan 1, 1953

By S. H. Ash

Probably one of the most significant departures in tunneling practice is the introduction of Diesel locomotives far haulage (Diesel trucks have been used for some time). The fallacy of the belief that they do not generate carbon monoxide or toxic gases and can be used indiscriminately has been proved by the authors through observation for several years of atmospheric conditions surrounding the use of Diesel engines in tunnels. Diesel locomotives haves been introduced in tunnel haulage for reasons other than safety or health. Except to the extent that they replace trolleys, with their danger of causing electrocutions, modern Diesel locomotives do not increase safety Or remove any ordinary hazards to safety or health. In fact, they create such hazards, the extent of which is limited entirely by the carbon monoxide-content level set, method of ventilation, adequacy of the measures.

Jan 1, 1942

By W. S. Wright

"INTRODUCTION The Ward copper deposit was brought to the attention of the Bureau of Mines in September 1943 by John J. Knob, 217 E. Penn Street, Long Beach, N. Y. At that time all Bureau of Mines work on Seward Peninsula was being directed to the exploration of deposits of tin, a metal high on the strategic list. It was not until September 1946 that the Bureau could make a preliminary examination of the Ward prospect.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.Acknowledgment is extended to Robert S. Sanford, acting chief of the Alaska division, under whose supervision all exploratory work of the Territory is conducted."

Aug 1, 1947

By A. R. Rule

A flotation process was developed by the Bureau of Mines for separation of carbonate and phosphate minerals occurring in unaltered phosphate ores of the Phosphoria formation. The process involves depression of phosphate minerals with fluosilicic acid and flotation of carbonate minerals with fatty acid emulsions. In individual laboratory tests, selective removal of carbonates was achieved with phosphate recoveries ranging from 60 to 80 pct P205. In continuous-circuit testing, sizing and separate treatment of coarse and fine fractions was necessary to achieve 65-pct P205 recovery. Concentrate grade ranged from 26 to 33 pct P205. The flotation tailings containing primarily carbonate and phosphate minerals is a potential fertilizer material. When reacted with H3P04, concentrated superphosphate containing approximately 40 pct available P205 was obtained.

Jan 1, 1974

By Lewis M. McNay

Description of methods employed and cost data are given for surface-mined land reclamation in Moraine State Park, Butler County, Pa. This project was conducted under the authority of the Appalachian Regional Development Act; a total of 177 acres of land was rehabilitated for specific land use purposes. The use of large equipment expedited the project work, and similar results could be anticipated on similar reclamation programs.

Jan 1, 1970

By Sathit Tandanand

Horizontal displacements and ground strains induced by mine subsidence are significant information needed for calculating damage and developing precautions against subsidence effects on surface structures. To devise a simple method for determining the surface horizonal displacements and strains simultaneously with the subsidence prediction, the U.S. Bureau of Mines examined the significance of the tilt number, which is the proportionality constant in the relationship between the horizontal displacement and the slope of the subsidence profile. The ratio of the tilt number to the critical radius of the subsidence trough is identical to the ratio of the maximum possible horizontal displacement to the full subsidence, which is found to be constant in most European coalfields. If this ratio is known for a particular minesite in the United States, then horizontal displacement and ground strains can be readily obtained from the primary subsidence data.

Jan 1, 2010

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By D. J. Bauer

This report covers a phase of an extraction project carried out as part of a research program on rare-earth technology. The current project--the production of pure cerium compounds--is an intermediate step between ore processing and metal reduction. In this connection, a study on a separatory-funne1 scale was made on nonreducing extractants for recovering cerium (IV) from tri-n-butyl phosphate (TBP) and of methods for recovering the cerium nitrate from the strip solution. Dilute sulfuric acid was found to be 100 percent effective in stripping cerium (IV). Several precipitants were effective in recovering the cerium from the strip solution, and ethanol was especially promising. A scaled-up investigation was made into the use of spray-tower type equipment to perform the function of extracting, washing, and stripping. This equipment, referred to as the pressure-bubbler, utilized the system developed on the separatory-funnel scale. Feed solutions were prepared from a bastnasite concentrate by two techniques. Of these, the sulfated bastnasite solution was most successful, resulting in 86-percent recovery of the cerium at 99.7+-percent purity.

Jan 1, 1959

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950