Search Documents

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By William C. Cooley

[Data from t.-raturs on each hydr,ne has been assembled on the- data sheets whichw6ed in this Appandin. Dai_iis are provl_ od for ::amines or hydraulic s-ctions in the USSR (TDPhw~s), 8 in ASR (Kuzbass) , 1i-gin i, 1 in 7in China, i in Japan, and l in C~n- i.Ata sheetsiov tion prepared for mines in New Zealah_~sddered very rele¬ vant, nor forf !aA of information. In aW,!~.F in : --- C=SR for tiara ShoeLS ara 1palAwdl satinieral mines have operac- ~ - re Manned about which very limited data exist as folloos:]

Jan 1, 1975

By Perry G. Cotter

The borides of the transition metals in Groups IV and VI exhibit, in addition to a certain degree of hardness, considerable resistance to heat and oxidation. They have high melting points (1,850°-3,060° C.) and low coefftcients of thermal expansion and can be bonded with other materials and hot-pressed to desired shape (cermets). Suggested uses for the borides include use in rockets and jet engines, as thermocouple protection tubes, as containers for molten metals in die casting, as flame-plated coatings on less refractory compositions to prevent erosion by hot gases, and as control rods and neutron shielding material in nuclear engineering, The Federal Bureau of Mines investigation of zirconium diboride started in 1950 at the Boulder City Nev,, Metallurgy Research Laboratory, Its purpose was to reduce the cost of raw materials for the production of zirconium diboride.

Jan 1, 1961

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By K. O. Bennington

Cancrinite is one eonstituentof "red muds," a high-volume waste product of alumina production by the Bayer process. The Bureau of Mines determined the thermochemical properties of cancrinite as part of a program to provide such data for minerals of industrial importance. Cancrinite [Na7.68(A16Si6024)(N03)1.68 (H2O)4.1] was synthesized by reacting aluminum silicate gel with a solution of NaOH and NaN03, and the composition was determined by chemical analysis, differential scanning calorimetry, and thermogravimetric analysis. The heat of solution was determined by hydrofluoric acid solution calorimetry. The standard enthalpy of formation at 298.15 K, ?Hf°298, is ?Hf°298 = -3,487.97 ±2.6 kcal/mol, and the standard enthalpy of formation from the oxides and NaN03, ?H°298, is ?H°298 = -215.20 ±l.8 kcal/mol.

Jan 1, 1983

By Ludwig Schmidt

The policy of buying crude oil on a gravity basis , recently instituted by the major crude oil purchasing agencies in the Mid- Continent field , has caused a new and vital interest to be taken in the work of the U. S. Bureau of Mines for preventing evaporation of crude . From the early years of the industry oil men have recognized that the gravity of crude oil is usually an index of the gasoline content , but it has not been so generally known that the gravity of the crude oil decreases if evaporation is permitted . In 1919 the Bureau of Mines began a survey to determine the evaporation losses of crude petroleum in its various stages of handling from the well to the refinery , The results of this study are presented in Bulletin 200 ( Wiggins , J.H. , Evaporation losses of petroleum in the Mid- Continent Field , Bulletin 200 , U. s . Bureau of Mines , 1922. ) and Bulletin 225 ( Wiggins , J.H. , Methods of decreasing evaporation losses of petroleum , Bulletin 225 , U. S. Bureau of Mines , ( In press ) The findings of this survey were so startling that soon after the preliminary report had been published , several tank companies began manufacturing vapor- tight tanks for the purpose of reducing these important losses . Since that time the development of this type of apparatus has been so rapid that today , every oil trade journal carries numerous advertisements of vapor- tight tanks and equipment as well as technical articles dealing with various problems in connection with the elimination of evaporation losses , whereas three or four years ago the subject was scarcely even thought of. The present report has been prepared in response to numerous requests for information on the apparatus actually being used to prevent evaporation losses . At this time oil operators are also extremely interested in holding the lighter fractions in the crude oil in order to prevent a lowering in gravity . The practice of removing the vapors from crude- oil tanks by means of a slight vacuum and extracting the gasoline from them is not discussed here .

Feb 1, 1923

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By H. D. Baylor

This is the first of a series of papers describing mining methods and costs at cement plant quarries throughout the United States and deals directly with those methods employed and costs obtained at the quarry of the Louisville Cement Co. located at Speed, Ind. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Mr. J. M. Buohheit, superintendent of quarries, and Mr. H. E. Schoonover, quarry engineer, in furnishing data and in compiling this report.

Jan 1, 1930

By N. L. Wimmler

"INTRODUCTION The Southern Cross district in Deer Lodge County, Mont., has been chiefly a gold producer. Most of the production has come from gold-bearing hematite-limonite ores. Some of these ores were mined and shipped to smelters for use as flux in smelting copper ores. A magnetite deposit in the Pomeroy property, containing no gold or other economic nonferrous minerals, was mined from 1921 to 1923, the ore being shipped to smelters for flux.The iron-bearing deposits in the Southern Cross area were examined by Bureau of Nines engineers/ on June 28, 1943, and October 14, 1943. As a result, a Bureau exploration project was recommended; it was conducted during 1944. A magnetometer survey was first made of the magnetite-bearing area at and in the vicinity of the Pomeroy property. Exploration by diamond core drilling was then conducted within this area, and in the Southern Cross and Hold Fast properties. The cyanide tailings dump at the Hold Fast mill was sampled by auger drilling.This report presents the data obtained by the Bureau of Mines exploration."

Dec 1, 1946

By Jerry J. Gray

Transportation charges for mineral commodity movements in western Oregon and western Washington were determined mainly by a stratified random sample canvass of producers. Total 1965 mineral production value for this area was $53.3 million; the cost or charge to move this production from the mine to the consumer or to the point of consumption was determined to be an additional $38.7 million. Thirty seven companies were contacted as a sample out of a total population of 349; the statistically expanded sample production value deviated 3.6 percent from that obtained by the Bureau's annual canvass. The agreement between the sample results and the canvass totals demonstrated the effectiveness of the sampling method for obtaining data with a predesigned level of accuracy. For comparison, the north-central Idaho and western Montana area was studied, A random sample experiment was designed, but because of the dominance of a few major companies, a random sample technique would have required more visits to producers than if only the larger firms were contacted. Eighty-four percent of the 1966 mineral value ($198.6 million) was accounted for by interviewing 27 firms out of a total population of 199. Total transportation costs or charges for the area were $26.7 million. The significant difference observed between the relationship of minerals production value and transport charges between the two areas investigated can be attributed to the difference in the minerals produced. The western Oregon and western Washington region is a nonmetals-producing area as opposed to the predominance of metals production in the Idaho-Montana region.

Jan 1, 1968

By Charles E. Larson

Square Butte has no history of mineral development or production. Surface mapping, radiometric surveys and chemical analyses of rock samples reveal no mineral potential. The area has a speculative potential for petroleum and natural gas. INTRODUCTION The Square Butte Instant Wilderness Study Area, in Chouteau County, Montana, consists of 1,946 acres (788 ha) about 35 miles (56 km) southeast of Fort Benton and 50 miles (80 km) northwest of Lewistown (fig. 1). This study was performed under provisions of the Federal Land Policy and Management Act (Public Law 94-579, October 21, 1976), in conjunction with the U.S. Geological Survey, which is responsible for regional geological, geochemical, and geophysical investigations, and the U.S. Bureau of Mines, which determines the mineral potential of existing mines, prospects, or mineralized areas.

Jan 1, 1982

By James W. Ballard

The facts are generally accepted that an atmosphere containing large quantities of any dust is objectionable to breathe and that some dusts are more dangerous than others. Therefore, knowledge of the composition of dusts is important in evaluating the hazard entailed on exposure. At present, free silica, of which quartz is the most abundant form, is considered one of the most significant dusts, from the standpoint of pneumoconiosis, and one State5/ has established permissible limits of air dustiness on the basis of the free-silica content of rock. The amount of free silica in materials used for rock dusting also has been limited.6/ Determination of free silica or quartz, therefore, is important.

Jan 1, 1940

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992

By Frank C. Andreuzzi

The Division of Environmental Activities, U.S. Bureau of Mines, conducted a solid waste demonstration project on a burning coal refuse bank. The primary objective of this project was to develop and evaluate an efficient method of extinguishing burning coal refuse and moving it. A series of tests were performed using water monitors and related apparatus to quench the burning material and, at the same time, using earth-moving equipment to transport, spread, and compact the extinguished material. The method found to be most effective consisted of water-quenching the surface material to a workable depth, ripping, and removing the quenched material with a bulldozer and tractor-scraper. The total cost was estimated to be $0.44 per cubic yard.

Jan 1, 1970

By D. W. Butner

The blast -hole method for drilling and breaking ground is not new to the mining industry . For several years it has been used rather extensively in Canada , particularly in the gold mines , where it was first developed and where the major advances in the technique as applied to present - day mining problems have been made . At present , 40 mines in Canada and the United States are using the method in one form or another , and from all indications its use will increase in the future . In two California mines , blast -hole diamond drilling is now used for a part of or for all stoping operations , and in one of these it is used to some extent in development work . At the Mountain Copper Co.'s Hornet mine in Shasta County, about 50 percent of the pyritic sulfide ore produced is mined by the blast - hole method , and the U. S. Vanadium Corp. mines 80 percent of the ore produced at its Pine Creek tungsten mine in Inyo County by this method . At Pine Creek , long -hole drilling and blasting is used for mining pillars also , and in pre - stoping development . The blast -hole diamond - drilling method is not applicable to all types of ore bodies . A third property in California , the El Dorado Limestone Company , El Dorado County, tried the method for several months in 1943 and 1944 , but , owing to certain factors that greatly increased mining cost , the company soon returned to conventional mining methods .

Feb 1, 1948

By M. B. Shirts

Numerous alternative processes have been proposed as being potentially more economical or less polluting than the traditional smelting of copper sulfide concentrates. One such process as recently developed in the laboratory by the Bureau of Mines is composed of a two-stage fluid-bed, oxidation-reduction roasting followed by ammoniacal leaching, solvent extraction, and electrowinning. A copper-leaching recovery of 97.4 percent was obtained, and electrolysis of the acid strip solution deposited metal assaying 99.99 percent copper. The roaster gases contain over 95 percent of the sulfur at a concentration of 12 percent which is better suited for acid making or elemental sulfur production than conventional smelter gas. When considering byproduct recovery, a preliminary estimate indicates copper production costs are com-parable to the conventional smelters.

Jan 1, 1975

By S. S. Todd

[The purpose of this investigation was to obtain, heat-of-formation values a four Common titanates and, to conjunction with other requisite data, to derive free-energy-of-formation values In tem peratures in the range of 1,600°-1,800° K. T ht four titanites are tricalcium ?ditanite !['a¬spheremr?raritanar( rint-tir.rniurn rill( 1 This rc rr,rt sul,rlc?nu?nIs :r },r; vinu~ hul,lrc.irse,n3i n wlti h eht-rmnnIN-ti i n c {ar.a ai?rc? pu -,csseeri (or, 11 in(c-rnxiLIic co mrc+unrls conraininL~ rir:,niurrl. 'f Lac? !1~:)mc? c?xpcrirnc'ntnl n-ut rhod w,i. rna~loycul. lic?.ats of for rn:ltion of rlre comi?c,unr4~ it 29S.N. ut re mca,urc?,l by tioItl[ion e':iIorrr)utrv, using a ctrneaR }ryrlrc,fllanric-hY rir~chlorie- ,aci l mixttrrt .is rhr c-zle~rinrrrric- fluid and rc.actic~n rtu,liura}.]

Jan 1, 1956

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

This study was done to evaluate the economic and technical considerations of using pozzolanic materials in order to guide cement manufacturers, pozzolan producers, contractors, Government organizations, and others interested in concrete construction work. Five hundred and thirty-eight samples of pozzolanic raw materials were taken from 27 central and western States. These samples were evaluated by petrographic procedures, and about 200 of the most promising ones were given a complete series of physical tests (American Society for Testing and Materials) to evaluate further their suitability as a pozzolan. This investigation showed that deposits of natural pozzolan materials were widely dispersed in the central and western parts of the United States but that exploiting these deposits would depend on whether they could compete economically with an increasingly abundant industrial waste product--fly ash.

Jan 1, 1969