Search Documents

By Donald J. Keefe

The Remote Working Level Monitor (RWLM) is an instrument used to remotely monitor the Rn-daughter concentrations and the Working Level (WL). It is an ac powered, microprocessor based instrument which multiplexes two independent detector units to a single central processor unit (CPU). The CPU controls the actuation of the detector units and processes and outputs the data received from these remote detector units. The remote detector units are fully automated and require no manual operation once they are set up. They detect and separate the alpha emitters of RaA and RaC' as well as detecting the beta emitters of RaB and RaC. The resultant pulses from these detected radioisotope; are transmitted to the CPU for processing. The programmed microprocessor performs the mathematical manipulations necessary to output accurate Rn-daughter concentrations and the WL. A special subroutine within the program enables the RWLM to run and output a calibration procedure on command. The data resulting from this request can then be processed in a separate program on most computers capable of BASIC programming. The calibration program results in the derivation of coefficients and beta efficiencies which provides calibrated coefficients and beta efficiencies.

Jan 1, 1977

By R. V. Lundquist

This report describes results of tests on the desilication of solutions resulting from the leaching of lime-soda sinters. Desilication was accomplished by heating the solutions in an autoclave. A liquor relatively free of silica was obtained after 30 minutes of heating at 200 p.s.i.g. in the presence of lime. The addition of lime improved desilication, but the rate and efficiency of desilication was effected by the quality of lime used. The optimum quantity of lime for effective desilication was about 6 grams per liter. A lesser quantity gave poorer desilication, and a greater quantity increased the alumina loss without improving desilication. The alumina loss was approximately proportional to the lime added. A complex structure, called artificial noselite in this report, was the only silica bearing compound detected in the desilication precipitate. Other compounds present were Ca(OH)2 (calcium hydroxide), CaCO3 (calcium carbonate), and Ca [A1(OH)6]2 (hydrated tricalcium aluminate). Sodium carbonate in the leach liquor retarded the formation of the calcium aluminate; hence it decreased the alumina lost to the precipitate. The extraction of alumina from aluminum silicate materials by the limestone soda-sinter process has been investigated by the Bureau of Mines for many years. The process consists of the following major operations: Blending the aluminum silicate with limestone and soda ash in such proportions that dicalcium silicate and sodium aluminate are formed on sintering; leaching the sinter in a carbonated caustic solution to extract the soluble alumina; purifying the leach liquor by the precipitation of soluble silica (this precipitate is designated desilication precipitate in this paper); precipitating alumina trihydrate from the purified liquors by carbonating with carbon dioxide gas; and calcining the trihydrate to alumina. Commercial grades of

Jan 1, 1962

By B. E. Blair

"This report presents the physical properties and related geological and petrographic data of some 84 rock types from operating mines, quarries, or blasting research test sites. These fundamental rock data were collected as a quantitative approach to underground mining problems, blasting research, or other related studies; however, the data are equally applicable to any problem wherein rock characteristics are important factors. Stress-strain curves are given where available, and the standardized procedure for determining elastic constants from static tension tests is described. Computed (laboratory) and measured (field) free-medium velocities are compared in those instances where such data are available. A chart is given showing both the optimum and minimum number of test specimens for the various core sizes employed in the Bureau of Mines standardized physical-property tests. Rock-type, geographical, and geological indexes are included to aid the reader in locating physical-property data in this and previously published Bureau of Mines physical-property reports.INTROD'OCTI ONThis report presents the physical properties of 84 rock types tested from 16 different projects (sections 37-52). Two previous physical-property reports 2-3 / (hereinafter referred to as parts I and II) presented data on 160 rock types from 36 different projects (part I, sections 1-25 and part II, sections 26-36).The physical-property data were originally obtained to supplement structural mining problems, seismic studies, or related investigations; however, they should be equally applicable in all fields of studies where the strength, hardness, or other properties of rock are important factors. The properties, determined from laboratory tests performed on diamond-drill core, include the following:"

Jun 1, 1955

By G. E. MeGlelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores. This technology has been adopted on a broad scale by the precious-metal-processing industry. This report presents information on the application of agglomeration technology to finely ground precious-metal-bearing tailings. Two commercial operations that have benefited from agglomeration technology are discussed. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1985

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 34,000 acres of the 58,040-acre Little Jacks Creek Wilderness Study Area (ID-111-6) in order to evaluate the mineralized resources. The study area is located in Owyhee County, 10, about 21 miles southwest from Bruneau. No mining districts are in the study area, nor were any mines or claims recorded or found. The northern half of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Little Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By W. W. Adams

Increased employment and a lower accident-frequency rate were the outstanding features of the metal- and nonmetal-mining4 industries of the United States in 1939 compared with 1933, according to reports furnished by individual mining companies to the Bureau of Vines, United States Department of the Interior. Except for 1937, the reports for 1939 showed gains both in number of employees and number of mar -hours worked over all years since 1929. The accident-frequency rate per million man-hours of exposure to mining hazards was lower than in any year since 1925. Reports for 1939 revealed a total of 111,909 men employed in and about mines, an increase of inure than 8 percent over 1931 The total volume of labor performed at all mires was slightly more than 299 million plan-hours, an increase of mare than 10 percent over 1938. As these gains suggest, the average employee had a longer period of work in 1939, the increase amounting to r workdays per employee.

Jan 1, 1941

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By Carlton E. Brown

[The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted. in South Africa about 19164/ and more recently in England5/,6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting.]

Jan 1, 1938

These proceedings consist of an overview of the in situ mining research currently being carried out by the Bureau of Mines. The following papers emphasize two general aspects of the in situ mining method: the environment and productivity. Both areas are extremely important, particularly because in situ leach mining is a relatively new mining method from a commercial point of view. Topics covered include the restoration of ground water, the selection of lixiviants, in situ mining of commodities other than uranium, in situ mining costs, the application of resistance measurements to in situ mining, an acid leach mining case history, and the use of branched boreholes for in situ mining. A bibliography of Bureau of Mines publications on in situ mining is appended.

Jan 1, 1981

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;' the arsenic concentration is similar in both fuels.

Jan 1, 1978

By R. L. Levens

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface area exposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 2010

By D. L. Nussear, W. E. Wallace, N. Clark, M. Gautaum, G. Hong-Guang

"Results of a research effort directed towards identifying and measuring the genotoxic properties of respirable particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented. Particulate matter emissions from a direct injection diesel engine have been sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust from a caterpillar 3304 diesel engine, representative of the ones found in underground mines, rated 100 hp at 2200 rpm is diluted in a multi-tube mini-dilution tunnel and the particulate matter is collected on 70 mm fluorocarbon coated glass fiber filters as well as on S"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the genotoxic potential. Results to-date on diesel exhaust have indicated that use of a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offers a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within. Protocols have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surf ace and physical properties of the particulate material. Evidence has been gathered to show that diesel soot expresses mutagenic potential as dispersions in DPL in the Ames tests as well as sister chromatid exchange activity in the animal lung fibroblast ·derived V79 cell line. The results are comparable to the standard solvent extraction procedure. INTRODUCTIONDiesel engines are primarily associated with transportation; however, they are also very common in the work place. Of particular concern is the use of diesel engines in mining operations. Currently there are 1,950 diesel machines working in underground coal mines throughout the country. These units are used in 151 mines encompassing nine different states (MSHA, 1991). It is believed the use of diesel powered equipment has contributed to higher productivity in these mines. However, the exhaust from diesel engines operated in underground mines has been a subject of concern during the past decade because of its suspected relationship with health aspects. The particulate matter generated by the diesel engine is of particular concern."

Mar 1, 1992

By Carroll W. DeKock

Thermodynamic data for selected metal sulfates were critically evaluated and compiled as part of the Bureau of Mines program to provide a scientific base for use in developing new technology and predicting the feasibility of new processes. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?RC, ?Gf°, and log Kf as functions of temperature are given in tabular form. Thermodynamic data were compiled for Ag2SO4, A12(504)3, A12(S04)3?6H20, BaSO4, BeSO4, BeSO4?2H2O, BeSO4?4H20, CaSO4, CaSO4?1/2H20, CaSO4?2H2O, CdSO4, CdSO4?H20, CdS04?8/3H20, 2CdO?CdSO4, Cs2SO4, In2(S04)3, K2504, KA1(S04)2, KA1(S04)2?12H20, Li2SO4, L12SO4?H20, MgSO4, MgSO4?H2O, MgSO4?2H20, MgS04?4H20, MgS04?6H2O, MgS04?7H2O, Na2SO4, Na2S04?7H20, Na2SO4?10H20, (NH4)2SO4, NH4A1(S04)2, NH4A1(S04)2?12H20, PbSO4, Rb2SO4, T12SO4, and Zr(S04)2.

Jan 1, 1986

By W. F. Marshall

This report describes exhaust-emission data from 10 diesel engines: six 4-cycle, direct-injection, naturally aspirated engines; two 4-cycle, direct-injection, turbocharged engines; one 4-cycle, precombustion-chamber, turbo-charged engine; and one 2-cycle, direct-injection engine. These engines were tested over a 3-year period (1968-70). Lowest emissions were obtained with a precombustion-chamber engine. Emissions from the 2-cycle, direct-injection engine fell within the range of emission rates for the 4-cycle, naturally aspirated, direct-injection engines. Excluding the precombustion-chamber engine and excepting one of the 4-cycle, naturally aspirated engines, carbon monoxide emission rates were about the same for all engines tested. Test data on smoke, odor, and emissions of hydrocarbons, oxides of nitro-gen, carbon monoxide, and aldehydes are given.

Jan 1, 1971

By E. G. Baglin

The Bureau of Mines devised a procedure for selectively extracting platinum-group metals (PGM) and gold from Stillwater Complex flotation concentrate. The Stillwater Complex is the only major U.S. PGM resource. Development of a suitable extraction technique will contribute to its exploitation. The concentrate was roasted at 1,050° C to convert host base-metal sulfides to oxides and the PGM from sulfide minerals to their elemental states. The roasted concentrate was preleached with dilute sulfuric acid to remove easily soluble gangue minerals. After pre-leaching, the concentrate was slurried with 6M HCI and leached at ambient temperature and pressure with a strong-oxidizing agent. Hydrogen peroxide, chlorine, sodium hypochlorite, nitric acid, and a persulfate salt were the oxidants investigated. The two-stage leaching scheme ex-tracted up to 97 pct of the platinum, 92 pct of the palladium, and 99 pct of the gold from the roasted concentrate. The base metals were not solubilized and reported to the residue. No attempt was made to devise a procedure to recover the copper and nickel because they comprise less than 5 pct of the value of the concentrate. Viable techniques for recovering the precious metals from the pregnant solution were sulfide precipitation, cementation with nickel, or adsorption on activated carbon.

Jan 1, 1985

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By R. L. Rankin

The program objective was to conduct surveys of respirable dust concentrations in coal mining operations at locations outby the working face. The results of these surveys were directed toward 1. identifying outby dust sources, 2. evaluating the severity of the major dust sources, 3. establishing dust sampling frequency, 4. establishing dust sampler locations, and 5. assessing the? areas of influence of the dust sources. The study included dust sampling of only nonhigh risk personnel and areas at six dif-ferent mines. Thirteen continuous mining, four longwall and two conventional mining sections were sampled. The severity of outby respirable dust sources such as load points, runways, dump points, beltways, transfer points and main haulage operations were characterized and areas within the mine were ranked according to severity. Information on engineering controls was also acquired. Guidelines for implementing a dust sampling program are presented and include sampler locations, ventilation surveys, dust surveys, effects of shift-to-shift variations, and sampling frequency.

Jan 1, 1980

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958