Search Documents

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By G. S. Scott

It is sometimes desirable to know what changes in sizing characteristics would appear in screened coals if screens of different - size openings than those employed had been used . This report is concerned entirely with the application of the Rosin- Rammler law to a solution of this problem .

Dec 1, 1943

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By Heinz W. Sternberg

A method for the electrochemical reduction of the benzene ring was developed and applied to the electrochemical reduction of coal. Successive electrochemical reductions of a vitrain from low-volatile bituminous coal in ethylenediamine saturated with lithium chloride resulted in the addition of 53 hydrogens per 100 carbon atoms. Ultimate analyses and pyridine solubility of the vitrain recovered after each reduction showed that hydrogen added at the beginning has a much greater effect on solubility than hydrogen added at a later stage. Surprisingly, the removal of sulfur from the vitrain takes place only after the more reactive aromatic rings are reduced. Nuclear magnetic resonance analysis and average molecular weight determination of the extracts of the reduced vitrain samples, representing about 18 percent of the vitrain, showed that these fractions had 95 percent of their hydrogen content on saturated carbon atoms and an average molecular weight of 800 to 900. A study of the effect of operating variables on current efficiency showed that current efficiency is highest with aluminum as cathode material and with lithium chloride as electrolyte. A substantial increase in current efficiency of difficulty reducible olefinic double bonds was achieved by adding a proton donor. This result is significant in connection with the electrochemical reduction of coal which proceeds from readily reducible aromatic double bonds to difficultly reducible isolated double bonds. It is proposed that reduction is achieved by electrolytically generated and subsequently solvated electrons and hence does not require prior adsorption of the substrate at the electrode surface. This offers a distinct advantage for electrolytic reduction of sparingly or insoluble substrates such as coal.

Jan 1, 1967

By J. P. Hansen

Wustite beds were reduced with carbon monoxide and mixtures of hydrogen and nitrogen in the temperature range 900° to 1,300° C to determine the effect of temperature, gas flow, and surface area on the rate of reduction to iron. The composition of the gas stream as it passed through the wustite bed was continuously measured with infrared absorption cells and heated-wire methods. The change in composition was used to calculate the reaction rates. Arrhenius plots of the data give heats of activation of 34 kcal for particles using CO, 27 kcal for particles using H2, 24 kcal for pellets using C8, and 6 kcal for pellets using H2. The velocity of reduction is dependent on the area of reacting interface and the driving potential of the gas (reducing gas concentration minus equilibrium concentration) as well as the exponential temperature effect. The reaction rate was independent of the gas velocity over the range of conditions studied.

Jan 1, 1965

By Michael J. Brnich

During the past 15 years the number of reportable mine fires has declined. A decline in the number of reportable fires is a gross indicator that allows experts to say something about the underground coal industry generally: There has been some improvement in overall mine fire preparedness. However, such an indicator is less reliable as a predictor of readiness at any particular operation. An indication of fire fighting preparedness would have to be assessed from evidence gathered at the mine site. In other words, there are two levels from which to view the problem. On a general level, there has been significant improvement in the industry's fire response capabilities over the past two decades. Specifically, however, little data has been gathered on a site-by-site basis to determine what improvements might be made on a local level. These improvements would move beyond regulatory compliance. It is expected that this manuscript, based on work conducted at an underground coal mine in the western United States, will help to focus attention on some central concerns involving this critical issue.

Jan 1, 2006

By Martin J. Gavin

During the present study of lubricating oils in the San Francisco laboratory of the Bureau of mines it became desirable to distill oils used in the experimental work at pressures as low as 10 mm., (mercury column) absolute. In the effort to overcome difficulties and eliminate sources of error the apparatus described below was finally developed. The distilling flask is essentially the Hempel flask used by the Bureau of Mines for the analytical distillation of petroleum3. The complete apparatus is shown in Figure 1. As air leakage at connections is an ever present or potential source of difficulty and error in vacuum apparatus, the, mouth of the flask is drawn down to one cm. internal diameter which materially simplifies obtaining an air-tight seal at this point. Before reducing the mouth, the spray screen is inserted and adjusted in position.

Jan 1, 1927

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0,5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that (1) the cost of slow cooling and crushing off-sets any advantages of higher copper recoveries from slow-cooled slag, and (2) water-quenched slag, which requires no crushing preparatory to grinding, could be treated more economically. Costs based on processing 1,000 tons of slag per day would be $1.85 per ton for quenched slag versus $2.37 per ton for slow-cooled slag.

Jan 1, 1971

By George H. Schnakenberg

This Bureau of Mines publication describes a passive personal sampling device for N02 in air, developed by the New York University Medical Center under Bureau Grant G0133066. The sampler has been successfully demonstrated in the field and in the laboratory. In corroborative laboratory trials the agreement with reference method is excellent. The overall accuracy is approximately ±5 pct of reading to a precision of about ±l pct. All evidence indicates that these samplers should indicate the time-weighted-average N02 concentration to the above accuracy and precision equally well in the field since effects of wind velocity and relative humidity are negligible and the effects of temperature are about 0.1 pct per °F. The duration of exposure and the approximate temperature are the only data that need to be collected in the field. A two-step analysis procedure in field or service laboratory is then used to obtain the total cumulated exposure to N02 in parts per million-hours (ppm times hours), which can be converted to the time-weighted-average concentration of N02 in ppm by dividing cumulated exposure by the duration of the exposure.

Jan 1, 1976

By Oliver Bowles

"The American Consul at Guatemala City reports that the Guatemala Marble Mining Company is preparing to operate a marble quarry about 13 miles from the railroad station of Zacapa, which station is a little over 100 miles from Puerto Barrios, the nearest port from which the product may be shipped. The deposit is extensive, and though somewhat broken up in places, great quantities of sound marble are available. It is claimed that the marble is equal in quality to the best product of the Italian Carrara quarries.Access to the quarry by rail is obtained by a spur track of the International Railways of Central America (Ferrocarril Internacional de Centro America) from Marmol, 3 miles south of Zacapa. This spur is about 5 miles long and terminates at the foot of the mountains. A double-track incline cable-way 2000 feet in length has been constructed to bring the marble down the mountain. From the top of the incline to the quarry there is a railway six miles in length over which the rock will be hauled by two side-geared Shay locomotives."

Mar 1, 1920

By Edward D. Thimons

This Bureau of Mines report presents expected levels of air pollutants in the face areas of oil shale mines, based upon data collected by the authors and previous investigators. Ventilation requirements to maintain these pollutant levels below their threshold limit values and Federal and local mine air quality standards are discussed. Two practical face ventilation systems are discussed in terms of actual in-mine test experience.

Jan 1, 1986

By Daniel T. Rogers

The Bureau of Mines, in its alumina miniplant project to investigate alumina recovery from domestic, non bauxitic ores, has conducted research on the use of a hydrochloric acid leaching, gas sparging crystallization technology. An important element of this research is the efficient separation of undissolved, siliceous residue from AICI3 -bearing leach liquors by continuous, horizontal, countercurrent vacuum belt filtration. In an effort to calculate material balances quickly and to predict material balances based on different belt filtration configurations, the perfect-mixing-cells-in-series model (PMCS) for calculating material balances around belt filters was used. Because of the porous nature of the solids, the model produced erroneous material balances. Therefore a reliable model, the shrinking voids model, was developed postulating the presence of an unwashable voids liquor volume that decreases with decreasing liquor AICI3 concentration. This volume decrease postulation is equivalent to assuming that dilute liquors flow more freely, causing more voids liquor volume to become washable. Least-squares based computer programs are provided, which are useful not only in producing material balances from plant data but also in predicting balances for untested configurations using the same feed materials.

Jan 1, 1982

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

By G. W. Jones

Explosion hazards that may exist when air becomes polluted with combustible gases and vapors are extremely dangerous, particularly if the volume of gaseous atmosphere is large, and an explosion under such circumstances could do tremendous damage to persons and property. The hazard is even greater if explosive mixtures are confined under high pressure, as the pressure could increase to tremendous proportions just before the container would rupture. Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and published its findings. The explosibility of natural gas has been studied, and the limits of flammability have been determined and published. Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide.

Jan 1, 1949

By A. D. Hahn

This report describes reconnaissance by the Federal Bureau of Mines of titanium-bearing sandstone in Kemper County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing Eocene deltaic formations" The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (Ti02), titanium oxide, is used mainly in producing welding-rod coatings and titanium metal. The fieldwork was conducted during the first half of November 1959. Seven holes, totaling 304 feet of bore, from which 64 samples of cuttings were taken, were drilled in the north-central part of the county; and two holes, totaling 172 feet of bore, from which 34 samples of cuttings were taken, were drilled in the southeastern part.

Jan 1, 1961

By R. G. Dressler

The Federal Bureau of Mines designed, constructed, and operated a demonstration plant at Louisiana, Mo., to produce gasoline, liquid fuels, and organic compounds from coal by a modified Fischer-Tropsch gas-synthesis process. Satisfactory equipment was developed to produce and purify synthesis gas and convert it into the desired products. Coal or coke was gasified with oxygen and steam to make a gas consisting essentially of carbon monoxide, hydrogen, and carbon dioxide. Dust in the raw gas was removed by cyclone separation, water scrubbing, and electrostatic precipitation. Carbon dioxide, hydrogen sulfide, and organic sulfur were removed with diethanolamine, iron oxide, and activated carbon. The gas was passed over iron catalyst and was converted into synthetic liquids, which were then separated and fractionated into gasoline, diesel oil, other liquid fuels, and oxygenated organic compounds. A 39-day continuous run demonstrated the feasibility of the process. Addition of 3 milliliters of tetraethylead per gallon of upgraded (or finished) gasoline gave a product with an octane rating up to 90 by the research method. After a caustic wash, the diesel oil was of a superior quality; its cetane number was 60 or above.

Jan 1, 1961

By John J. Henn

As part of the U.S. Department of the Interior programs on rutile, authorized by the Office of Emergency Preparedness in June 1967 under provisions of the Defense Production Act, the Bureau of Mines reviewed available literature on major proposed processes for producing rutile substitutes. The processes are grouped according to the major processing step, and important operating features are described. Sixty-one references are cited.

Jan 1, 1970