Search Documents

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By R. Clark Lantz, Charles Stanley, David E. Hinton

Morphometric examination of lung alterations following exposure to toxic and pathogenic substances is invaluable in detecting subtle changes which might otherwise be overlooked. Results, from evaluation of initial structural alterations, support and guide subsequent nonmorphological techniques and, when coupled appropriately, can lead to a better understanding of the pathogenesis of a disease. Morphometry is a technique which can be used to determine, quantitatively, the site, extent, development, and progression of a disease state. Determination of the extent of tissue and cellular involvement in the response to inhalation of silica has been performed in order to gain a better understanding of the development of fibrosis following inhalation of this toxicant. In addition, since silica has been postulated as one of the important pathogenic minerals in coal mine dust' it is important to understand the lung tissue response to silica prior to evaluating the effects of inhaled coal mine dusts. Male Syrian golden hamsters were placed in Hazelton 1000 inhalation chambers and were exposed to either filtered air (controls, n = 24) or filtered air plus 30 mg!m3 silica (Min-U-Si110,95%ofparticles < 5 um,n =24)for16hours per day, five days per week, for two weeks. Animals were returned to the animal quarters prior to subsequent tissue processing at 1, 4, and 12 weeks following exposure. This schedule was designed to allow time for the development of fibrosis. Lungs were fixed by intratracheal perfusion of ½ strength Karnovsky's fixative at a pressure of 20 cm H20 and tissues were taken for embedment and analysis at the light level. Determination of site, extent, and development of alterations was performed using a multitiered approach. Changes in large structures (airways, blood vessels) was determined prior to evaluation of changes at the septal tissue level. Data will be presented outlining the progression of changes. Results indicate the usefulness of morphometric analysis of lungs following inhalation of toxic substances in quantitatively defining the structural alterations.

Mar 1, 1989

By C. H. Fisher, Abner Eisner

"INTRODUCTION Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils 4 such as gasoline, kerosene, and neutral oils from coal—tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 60 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin—free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin—free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water—soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiatingbetween cyclic (naphthenes) and acyclic hydrocarbons (paraffins). Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons,It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings."

Dec 1, 1937

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By M. L. Williams

In recent years the use of visual aids has expanded the? field of safety education. This is a modern adaptation of a method employed in ancient times, when simple paintings and drawings were the only means of recording current events. In its present application, visual aid employs sound and silent motion pictures, stripfilms, lantern slides, descriptive posters, and color. According to Roberts,3/ "Visual education is a method of imparting information which is based on the psychological principle that one has a better conception of the thing he sees than of the thing he reads about or hears discussed." Dent4/ further defines visual aid as "all the materials used to facilitate the understanding of&apos; the written or spoken word."

Jan 1, 1951

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of&apos; determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau&apos;s research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By R. Blickensderfer

An impact wear testing machine was devised by the Bureau of Mines that simulates the repeated impact conditions encountered in large milling and grinding operations where breakage and spalling are problems. The apparatus provides data on materials that may help in the design of alloys with improved resistance to deformation, spalling, and breakage. The test blocks are 2 in thick by 6 in by 8 in. Impacts are produced by dropping 3-in-diam balls weighing 4 lb from a height of 10 ft. Tests were run until breakage occurred or to a total of 100,000 impacts. Four types of failures of the test block were observed: (1) cold flow of the bulk material by plastic deformation, (2) flaking of the surface in the impact region, (3) spalling of the block to form a crater in the region of impact, and (4) breakage of the test block into two or more major pieces. The effects of composition, heat treatment, microstructure, and hardness on types of failure are discussed.

Jan 1, 1983

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966

By P. S. Haury, Thomas C. Denton

"INTRODUCTION AND RESUMEThe Reward zinc property was one of the first selected for exploration by the Bureau of Mines at time when zinc supplies for war production were very short. Preliminary examination indicated that an appreciable tonnage of zinc that could be developed for early production might be found by diamond drilling. The geology was mapped by the Federal Geological Survey, and 14 holes were diamond drilled by the Bureau of Mines. This work was started in September 1942 and completed in September 1943.The Reward is an old property in southwestern Pinal County, 26 miles from Casa Grande on the Southern Pacific Railroad. Mining was begun in the early 1880's and was continued intermittently by several operators to about 1917. About 400,0oo pounds of copper was produced from the north¬eastern part of the property, mainly from a 600-foot incline in oxidized copper ore that replaced a bed of limestone. This ore was mined out. A 400-foot vertical shaft in the copper area was inaccessible. A 325-foot vertical shaft had been sunk near the southwest end of the zinc-bearing area, and a 600-foot crosscut tunnel had been driven near the northeast end of the zinc area, but little zinc ore was produced. There were several shallow inclines and numerous surface pits between the main workings.The ores were deposited in Paleozaic limestones that strike northeast and dip about 40 degrees northwest. These are capped by Cretaceous clastic and volcanic rocks in the zinc area. The outcrops show mineralization in a segment of the limestone 4,500 feet long, which is limited by large cross faults at each end. Another large fault, which strikes north, separates the northeast third of the mineralized belt from the remainder. Copper predominates northeast of this fault and zinc southwest of it. The ore beds are cut by numerous small cross faults. Ore was deposited for short distances along some of these, but more of it made out from the fissures along certain replaceable limestone beds."

Nov 1, 1946

By G. A. Smyres

A GaC12--B2 l-eachtng procedure and meEal-recovery method for treating an arsenical Cu-Co sulfide concentrate was developed by the Bureau of Mines as an alternative to smelting, which is no longer considered an environmentally acceptable method for treating arsenic-containing ores. The procedure involved leaching in a CaC12 solution with CaC03 for 96 h at 26 pct solids (concentrate and CaC03), 1150 C, and a pressure of 50 psig (345 kPa) with oxygen. More than 98 pct of the cobalt and 97 pct of the copper were extracted, and 99.98 pct of the arsenic and 99.9 pct of the iron remained in the leached residue. A filtration rate of 2.9 gal/(ft2.h) [118 L/(m2.h)] and a cake formation rate of 36 Ib/(ft2.h) [172 kg/(m2.h)] were obtained by filtering reacted pulp at 1000 C. More than 99 pct of the copper in the pregnant solution was extracted as CuCl2 by golvent extraction with a new copper extractant. Copper was stripped from the loaded organic with a sulfate-chloride solution, which was used as the anolyte for electrowinning of copper in a membrane cell. Copper plate produced was more than 99.99 pct pure and requi.red 0.81 (kW&apos;h)/lb Cu [1.78 (kW·h)/kg Cu]. Cobalt sulfide was precipitated at pH 3 with Ca(HS)2.

Jan 1, 1986

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION The investigation of the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the study of methods for eliminating these hazards, conducted by the Bureau of Mines, the Edison Electric Illuminating Co. of Boston, and the Boston Consolidated Gas Co. since 1929, was continued during 1933.From May and through December 1933 these tests were supplemented by a study of the manholes of the New England Telephone & Telegraph Co. The test crew was under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Boston Consol¬idated Gas Co.The procedure of sampling manhole atmospheres and of shipping the samples to Pittsburgh was the same as that used heretofore. In previous reports the relative explosibility of the samples was calculated by adding the percentages of the illuminants, hydrogen, carbon monoxide, methane, and ethane, dividing the total by 6.5, and multiplying by 100. Experience has shown that the factor 6.0 is more nearly correct; therefore, this has been used in calculating the relative explosibility of all the samples listed in appendix A and B of this report. If gasoline vapor is present a smaller factor must be used.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of W. C. Bayliss, president of the Edison Electric Illuminating Co. of Boston; W. C. Beckjord, vice president and general manager of the Boston Consolidated Gas Co., and A. C. Fieldner, chief engineer, Experiment Stations Division, United States Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department of the Edison Electric Illuminating Co., cooperated heartily in furnishing both men and information for the work."

Oct 1, 1934

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By J. P. Powell

This report provides information on the techniques and results obtained on representative waterflooding projects in Cowley County, Kans. Records show that waterflooding was begun as early as 1935, but not until 1948 was the method expanded. The greater depths to the oil-producing formations in this area compared to those in eastern Kansas undoubtedly delayed the widespread use of secondary-recovery methods. This report presents a discussion of four waterflooding projects in Cowley County, Kans. The locations of these projects are shown in figure 1. The projects have been in operation from 1 to 7 years and have produced more than 1 million barrels of additional oil by injecting 11.5 million barrels of water. The projects are designed to take advantage of elevation and height of the separator tank to collect by gravity flow the produced brine at the respective treating or storage tanks. The closed-type water system is used on three of the projects and an open-type water conditioning system on the fourth. On one of the projects, which was drilled along a narrow shoestring formation, alternate well, were converted to input wells. However, most of the input wells for flooding converted producing wells.

Jan 1, 1958

By D. Harrington

Examination of numberous disasters , such as fires or explosions , and the evidence at coroner's inquests following such disasters in several States , have shown the writer how frequently men in charge of the operation and safety of mines have forgotten, or have failed to learn , details of safe mining practices , After securing a position of trust as superintendent , or a certificate of competency to act as shot -firer , fire boss , or mine foreman, some men seem to have felt it unnecessary to keep safety principles in mind , or to keep abreast of current progress in safety ; they have concentrated on getting out maximum tonnage at minimum cost . • In coroner's inquests , the testimony after disasters has shown that firebosses , foreman , and coal -mine superintendents are noticeably lacking in knowledge of the provisions of the State mining law relating to fans or doors , frequency of crosscuts , nature of stoppings necessary , electrical equipment , records of daily mine examinations , quantity of air required , or splitting and overcasting .

Jul 1, 1922

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

By A. Gene Collins, Cynthia A. Pearson, Cathy J. Waters

The chemistry of selenium and tellurium is discussed , along with a method of preparing a synthetic oilfield brine , an oilfield brine sampling method , and methods for determining selenium and tellurium in complex oilfield brines . Selenium either can be reduced to the elemental form with sulfur dioxide and determined semiquantitatively by color comparison of the red amorphous form or can be converted to selenite and determined quantitatively by reacting it with 3,3 ' - diaminobenzidine and obtaining its spectral absorbance at 420 mu . Tellurium can be reduced to the elemental form with hypophosphorous acid , and the spectral absorbance of its red hydrosol can be measured at 400 mu . Less than 0.05 mg / 1 of selenium and 0.1 mg / 1 of tellurium can be determined by the described methods .

Jan 1, 1964

By E. D. Gardner

"Introduction Ore from stopes in metal mines is generally dumped or drawn into chutes or raises through which it passes by gravity to the haulage levels. Occasionally, and under some conditions quite frequently, the ore in a chute will wedge or hang and refuse to run. This hanging of the ore may be due to the packing of damp or clayey material, to boulders forming an arch, or to loose lagging or other timber becoming lodged in the chute.In drawing material from a loading chute it is drawn out a car at a time, and the intermittent flow of the material .increases its tendency to hang. When the obstruction in the chute is near or at the loading gate, the chute pullers start the ore by punching it with iron bars inserted through openings in the chute gate. When the obstruction is beyond reach of the bars, other means of starting the ore must be used.In some systems of mining, chutes or ore raises are built with timber as the stope extends upward. Generally, a manway is left alongside of the chutes, and when the ore hangs in a chute usually it can be started by a miner from the manway ladder by pounding on the timbers of the chute or by punching the ore with a bar inserted through small holes in the chute lining. Special methods of starting clogged ore, such as shaking a chain left hanging in the chute, are used at some places.In other systems of mining, ore passes or chutes are run through solid rock and when the ore hangs in one of these passes, either it must be blasted or else started from the top. Sometimes the ore can be started by running water into the top of the chute, but if the water does not start the ore moving, it must be blasted from underneath. This is done by detonating a bundle of cartridges under the obstruction in the chute or raise."

Jan 1, 1927