Search Documents

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for surface sand and gravel mines by state during 1990-2001. Table 28 also shows the injury risk rates, employees' working hours, and lost workdays. At surface sand and gravel mines, a total of 70 fires with 60 injuries occurred in 29 states during 1990-2001. Fifty-nine of the fires caused 60 injuries (none of the fires involved contractors). The yearly average was 5.8 fires and five injuries. The Ewhr value was 741 x 106 hr (Irr = 0.016), and the LWD value was 6,921. California had the most fires (nine fires and five injuries), followed by Michigan (six fires and six injuries) and Pennsylvania (five fires and five injuries). Of these states, Pennsylvania had the highest injury risk rate value (Irr = 0.052). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries show an increase during the second period followed by a decrease during the fourth period followed by a small increase during the fifth period and a sharp decrease during the last period. Employees' working hours increased during most of the periods. The Irr values follow patterns similar to those shown by the injury values.

Jan 1, 2004

By William A. Hoffman

In This Chapter [MSHA regulations for coal mines MSHA regulations for metal/nonmetal mines OSHA regulations for tunnel construction Types of respirators used in mines and tunnels Filter materials and filter efficiencies Donning, seal checking, and maintenance Filter service life and Respirator information resources] In many cases, engineering controls are not adequate to achieve satisfactory dust levels, so respirators must be used. This chapter explains the Federal regulations governing the use of dust respirators in mines and tunnels and describes the most common dust respirators used. Filter materials and filter efficiencies for respirators are discussed. This chapter also gives some guide-lines for respirator use and recommends sources for more dust respirator information. Respirator effectiveness in reducing dust exposure usually exceeds the effectiveness of most engineering control methods. RESPIRATOR REGULATIONS [Different regulations govern respirator use in coal mines, metal/nonmetal mines, and tunnels under construction.] Coal mines under Mine Safety and Health Administration (MSHA) jurisdiction. Coal mine operators are required to meet dust standards using only engineering control methods. Typical engineering control methods include ventilation and water sprays. Respirators are not regarded as an engineering control method, so respirators cannot be used in lieu of engineering controls.

Jan 6, 2003

By James J. Hanslovan

Stresses that damage coal mine trailing cables were investigated to obtain a quantified description of cable-stress locations, magnitudes, and frequency of occurrence. Stresses occurring in operating mining sections were measured and observed. Answers to questions that arose during the underground investigations were pursued under controlled conditions, both in the field and in the laboratory. Cable-handling suggestions that minimize or eliminate the stresses are summarized in the form of recommendations to mine operators.

Jan 1, 1979

By Richard F. Hewlett

The mining industry utilizes a vast store of knowledge, wisdom, and engineering talent in designing mining systems. However, the complexity of the required systems and the presence of numerous variables frequently necessitates raking important decisions without having adequate accurately detailed information. That many of the decisions made in the past were nearly correct, in the long run, is substantiated by the number of successful mining enterprises that exist in the world today. Subsequent to 1940, the disciplines of operations research and systems engineering were developed. The disciplines have produced methods of providing better information to persons responsible for making decisions.

Jan 1, 1963

By E. Morrice

Gadolinium, dysprosium, and yttrium are difficult to electrowin as high-purity liquid metals because of their high melting points (>1,300° C). Samarium metal is difficult to prepare directly by electrolysis because the metal reacts with the electrolyte. In this Bureau of Mines study, the rare-earth metal was electrodeposited on a solid manganese, chromium, or iron cathode to form a low-melting alloy. The alloy was then vacuum distilled to separate the rare-earth metal from the ferrous metal. A typical samarium metal product, obtained as the distillate from vacuum distillation of a samarium-iron alloy, contained 150 ppm oxygen, 80 ppm carbon, and 50 ppm iron as impurities, Gadolinium metal, obtained as a residue from the distillation of a gadolinium-chromium alloy, contained 300 ppm oxygen, 200 ppm carbon, and 100 ppm chromium.

Jan 1, 1969

By J. P. Rider

Health surveillance efforts indicate that the development of lung disease and overexposure to respirable dust in underground coal mires continues to afflict mine worker. Results from the most recent round (1992 - 1996) of the Coal Worker's X-ray Surveillance Programs indicate that approximately 8% of the examined miners who had at least 25 years of mining experience were diagnosed with Coal Worker Pneumoconiosis (CWP) (category 1/0+). During the period between 1995-1999, mine operators and MSHA inspectors collected 9968 and 1365 dust samples respectively, from longwall designated occupation (DO) personnel. Analysis of these samples showed that 1970 (20%) of the mine operator samples and 25.8 (19%) of the MSHA samples5 exceeded the 2 mg/m3 dust standard. The continued development of CWP in coal mine workers and the magnitude of respirable dust over-exposures in longwall mining occupations illustrate the need for improved dust control technology on longwalls. Figure 1 illustrates the major longwall dust sources as determined in the early 1990's.4 This article describes the ongoing research to find ways to minimise shearer dust levels as a function of changes in dust control parameters, and research to determine the impact of high air velocities on shield dust entrainment.

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By N. Kumar Kittusamy, Richard E. Miller

This field study evaluated a newer and older dozer at a construction site. Both dozers performed similar activities in the same location within the construction site. Two operators participated in this study. One operator used the older equipment and the other operator used the newer equipment. Jolting and jarring measurements were taken at the seat/operator interface and at the floor of the cab. The result of this field study indicates that the newer dozer was better than the older dozer.

By Sabri Ergun

The method of constant compositions involves the determination of the time required for the attainment of a given conversion at various temperatures. Heretofore, it has been used in evaluating the energy of activation only. A development of the method, made in the present study, makes possible the evaluation of the functional dependence upon composition and the frequency factor in addition to the energy of activation. INTRODUCTION Kinetics of reactions are best analyzed in the light of the mechanism, energy requirements, and forces involved in the reaction. Such physico-chemical information is not often available in solid state phase transformations. The reaction rates are followed by changes in a physical property during the course of the reaction, and repeating the experiment at different temperatures permits the determination of activation energy only. The possibility of a complete kinetic analysis by such a purely "phenomenological" approach has been questioned.4/ In this report a method is developed making possible the evaluation of the functional dependence upon composition and frequency factor in addition to the energy of activation. The application of the method to a study of solid state order-disorder changes is demonstrated.

Jan 1, 1960

By R. Barany

The heats of formation at 298.15° K of calcium tungstate, calcium molybdate, and magnesium molybdate were determined by solution calorimetry. For the heats of formation from the elements, the values obtained were calcium tungstate, -402.4 ± 0.5 kcal/mole, calcium molybdate, -369.5 ± 0.3 kcal/mole, -334.8 ± 0.2 kcal/mole. For the heats of formation from the oxides J the values obtained were calcium tungstate, -49.2 ± 0.4 kcal/mole, calcium molybdate, -39.6 ± 0.1 kcal/mole, and magnesium molybdate, -12.9 [ ] 0.1 kcal/mole.

Jan 1, 1962

By L. E. Schultze

The Bureau of Mines operated a mineral recovery unit to recover metal values from post-flash geothermal brines from the Salton Sea known geothermal resource area as part of its research into the use of plentiful resources. The brine was available for metals recovery after its heat content had been used to generate electricity. The brine source was treated with lime to precipitate the contained iron, manganese, lead, and zinc before injection of the heat-depleted brine into the underground reservoir. Data are presented on the effects of process variables, such as rate and method of lime addition and air oxidation versus air exclusion. Variations in precipitation of metal values, composition of precipitates, effectiveness of slurry thickeners, and methods of treating the precipitates to recover metal values are discussed.

Jan 1, 1982

By BUREAU OF MINES

The approval of the U. S. Bureau of Mines when granted to a manufacturer for a gas mask is a certification that the particular device has been submitted to the Bureau of Mines for inspection and test and has been found to meet that bureau's published minimum requirements for safety , durability , and satisfactory performance . Any de- Gas masks are approved by the Bureau of Mines only as a complete unit or assembly of parts , as canister , facepiece and harness . This is in order that responsibility for rigid adherence to the bureau's requirements may be definitely located and not divided . vice marketed under this approval must be a unit composed of parts identical in detail of design , assembly , workmanship , and quality , and produced under the same control and inspection as the original device to which approval has been granted . The particular parts which comprise the approved assembly are designated in a letter to the manufacturer at the time the approval is granted . In recent years they are also specified in the approval plate authorized for use in connection with the sale of the device . Each part permitted in the assembly is legibly marked by name or number for the guidance of users of masks in ordering and identifying approved parts when making repairs , and thereby maintaining their equipment as an approved device . In view of the foregoing , any change in the design of parts or deviation from the permitted assembly of parts would violate the conditions under which approval was granted and the device would not be considered as meeting the approval requirements of the Bureau of Mines . The U. S. Bureau of Mines has been frequently requested to interpret the approval status of a gas mask assembled from parts which have separately met its requirements as components of two or more approved devices but which in the form of a complete unit has not been submitted for tests or been granted approval . Responsibility for the elements and for their proper assembly is in such case divided . Such assembled units have no status as permissible equipment under the Bureau of Mines system of schedules . The reasons underlying this policy are that the approval is granted only to some one who assumes responsibility for the whole and that the details of assembly and coordination of parts are considered to be important to the satisfactory performance and safety of the device .

Sep 1, 1932

By H. P. Greenwald, G. E. McElrey

"Part IV.- The Resistance Caused by Right-Angle Bends. IntroductionThis paper deals with the fourth phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the major results public as rapidly as possible. Parts I, II and III were issued as Serials Nos. 2621 (July 1924), 2647 (October 1904) and 2671 (March 1925) and dealt with the resistance of unobstructed entries, the resistance due to mine cars and, the resistance of timbered entries respectively.Description of the Tests With the last cutthrough between the two butt entries of the test section in the Experimental Mine open, the air flow was deflected, around two right-angle bends in the same direction, the butt entries being 50 feet center to center and approximately 6 by 9 feet in cross section. Each bend had a dead end opening off of it; that at the first bend was in the direction of flow and that at the second bond was at right angles to the flow. For a primary test condition the inner corner of each bend was trimmed square and the dead ends were closed off with board brattices set flush with the line of the cut-through.The two corners of the first band were, then modified both independently and in conjunction. Various modifications of both bends in conjunction were also tested with rather surprising results as to the effect of conditions at the first bend, upon the pressure losses at the second. To confirm the theory developed to fit these results a series of tests were made to give a direct comparison of the -pressure losses as between two bends with the air flow deflected in the some direction at each and with the air flow deflected in opposite directions. The former is designated ""double"" and the latter a ""reversed"" right-angle bend. This series of tests was conducted, however, on the bends at one of the intermediate cutthroughs at which the flow could be deflected us either direction at the second, bend. Here also the average cross-section was 6 by 9 feet and the bends were 50 feet apart."

Jan 1, 1928

By D. H. Chambers

The Bureau of Mines developed a process for producing high-purity zinc and tin by electrorefining from liquid amalgams. Commercial grade metals were dissolved in mercury to produce saturated amalgams at room temperature. Amalgams were also prepared by electrolytic transfer from soluble anodes of the metals to a mercury cathode. Amalgams formed by both methods were used as anodes in electrorefining cells to produce high-purity cathodes. Metal impurities, excluding mercury, were at levels of less than 5 ppm in zinc and 9 ppm in tin. Mercury content was about 2 to 10 ppm in zinc products, and this was effectively removed by heating the cathodes in a vacuum. Mercury was excluded from tin cathodes by pumping the tin electrolyte through tin turnings and controlling the cell temperature.

Jan 1, 1969

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

By W. J. Pena, C. W. Owings

"Generally, the hazard of cool-dust explosions in tipples and cleaning plants is not given the consideration that is given it underground. This lack of consideration is probably due to failure to appreciate the potential hazard. An explosion in a tipple or cleaning plant is basically little or no different from an explosion underground. If bituminous-coal dust is raised into a cloud in the air and comes in contact with arcs from motor brushes, switches, or open flame, the dust is very likely to ignite, and flame will very probably propagate or extend through it if the quantity of dust per unit of air space is sufficient. The open space in a tipple or cleaning plant may reduce the violence of the explosion, but it is not likely to prevent ignition or propagation of flame.The movement of coal through a tipple or cleaning plant naturally puts into suspension a large amount of dust, which finally settles on exposed surfaces. Any disturbance that will put this dust into suspension in a sense enough cloud can result in the dust being ignited by an arc or open flame if one should be present. An explosion of bituminous-coal dust in a tipple or cleaning plant generally can be prevented either by keeping it thoroughly clean or by removing all sources of ignition, or both.The tests at the U.S. Bureau of Mines Experimental mine have shown that the explosibility of coal dust is proportional (other things being equal) to the ratio of the volatile matter to the volatile matter plus the fixed carbon, indicated thus:The volatile ratio for the Pittsburgh coal bed is calculated as follows:Therefore, as the volatile matter decreases the liklihood of ignition decreases; however, coal-dust explosibility depends on other factors also, such as fineness, dryness, and cloud density; and under some conditions other factors also intervene.Proof of the explosibility of coal dust in the absence of explosive gas has been shown in numerous cases in mines and mine plants and also by a series of tests. In these tests a dense cloud of dust is blown onto an open flame or an electric arc, almost invariably with resultant exploding of the dust. The Safety Division of the United States Bureau of Mines has made a number of demonstrations of the explosibility of Pittsburgh coal-bed dust, using a small gallery or box in which a cloud of coal dust is blown onto a lighted match; larger-scale tests have been made with an electric arc as the igniting agent. Bituminous-coal dust is readily ignited with a medium arc, but with low-volatile coals a larger arc is required. For test purposes, a 100-ampere arc has been used. Ignition has occurred readily under these conditions with Pocahontas No. 5 coal dust with ratios of volatile to total combustible of 0.232 to 0.253, and with Pocahontas No. 3 coal dust with a combustible ratio of 0.242. Lower Kittanning coal dust, with a ratio of 0.187, did not give definite ignitions, and Pocahontas No. 4 dust did not explode, although part of the coal-dust cloud ignited. It is probable that even the low-volatile coal dust will be found to be explosive with a higher-amperage electric arc as the initiating agent."

Jul 1, 1936

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By John R. Bartels, Dean H. Ambrose, Richard C. Wang

This paper presents the results of a study to verify and validate a computer model that represents and analyzes motions and hazardous events in a simulated three dimensional workplace. The purpose of the computer model is to support research that is investigating the safe speed range for the vertical movement of roof bolter boom arms to reduce worker injuries in underground coal mines. The information obtained for this paper is based upon a project that is investigating means to reduce workers risks of injury from exposure to mining machinery. The methodology being employed by the project includes human factors design considerations, anthropometric modeling and simulation tools, laboratory validation, engineering interventions, and collaboration with industry and an equipment manufacturer. The results of this study were used to (1) determine the input parameters that are unique to the mining environment and needed to develop a credible, computer-based, human-machine interactive model, (2) develop test methods to measure the required parameters, and (3) to refine the human-machine interactive computer model.

By C. J. Thompson

In the course of the work currently conducted by the Bureau of Mines in cooperation with the American Petroleum Institute Research Project 48 on identifying sulfur compounds in petroleum, a micromethod was developed (12)5 for catalytically removing the sulfur atom from sulfur compounds. The product is the residual portion of the molecule; the structure otherwise was unaltered except for hydrogenation of any unsaturated bonds that were present in the original compound. Positive identification of sulfur compounds isolated from crude oils is a difficult problem. Direct comparison of properties of the unknown with those of reference compounds is often impossible because of the limited number of reference sulfur compounds available. However, a relatively large number of pure hydrocarbons is available, and the conversion of the sulfur compound to a hydrocarbon enhances the possibility of identification. The technique also can be used to prepare microquantities of scarce hydrocarbons by hydrogenating compounds that are readily available.

Jan 1, 1962