Search Documents

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By H. B. Humphrey, J. J. Forbes

"In accident prevention, a study of statistical data is necessary to determine primary causes of accidents to devise means to eliminate causes at the original sources. Explosions in coal mines of the United States during the 10 years ending December 31, 1931, ranked third in the causes of fatal accidents; they constituted 16.2 per cent of all fatal accidents in bituminous mines and 8.4 per cent of all fatal accidents in anthracite mines. A study of coal-mine explosions in Pennsylvania, with approximately 160,000 men employed in anthracite mines and about 145,000 in bituminous mines or about 205,000 out of -the approximately 525,000 men employed in all coal mines of the United States, should give information of value to all persons endeavoring to reduce or eliminate coal-mine explosions. This circular reviews explosions of gas or dust or of both in the coal mines of Pennsylvania to show the hazard of gas and dust, to point out the influence of certain factors in causing explosions, and to emphasize the efficacy of explosion-preventive measures.The data published annually by the State Department of Mines and of the United States Bureau of Mines were used in compiling the tables of explosions. Through the cooperation of W. H. Glasgow, secretary, Department of Mines of Pennsylvania, and his assistants, many doubtful cases were clarified, so that as far as recorded the history is comparatively complete. Figures used in compiling some of the tables were furnished by W. W. Adams, chief statistician, demographical division, United States Bureau of Mines.Anthracite in the Wyoming Basin of Pennsylvania was used locally by gunsmiths in 1755, by blacksmiths in 1769, and as domestic fuel in 1808.Mining and shipments developed slowly between 1806 and 1812, but more rapidly after that.Early mining along the outcrops gave essentially no trouble from gas, but by 1870, when State inspection was established, explosions were frequent; ventilation was crude and accumulations of gas were generally ""brushed"" or burned out.Table 1 lists 1,232 ignitions and explosions of gas in anthracite mines from 1870 to 1932, inclusive, every one of which was accompanied by loss of life. Some details are given of 110 representative cases in which five or more lives were lost or in which it appeared that some violence was present.During the period 1870 to 1932, inclusive, gas explosions caused 2,213 fatalities, or an average of about two deaths for each ignition or explosion. Records are not available as to the number injured in these and in other explosions where no deaths occurred, but from a study of explosion reports it appears probable that the number injured exceeds the number killed. In the 110 cases described, 599 were killed and 294 were injured. As shown in Table 2, fatalities from gas explosions averaged 8.3 percent of the total fatalities in Pennsylvania anthracite mines from 1870 to 1931, varying from 6.0 percent in 1931 to 13.1 percent in 1927."

May 1, 1933

By A. W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 14 coalbed samples collected in Wyoming. Such data is needed to evaluate the quality of the coals of the West where most of our low-sulfur-content coal reserves are found. Of the 14 samples included in this report 13 had a total sulfur content of 1.1 percent or less. All of the samples contained low per¬centages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile B bituminous to subbituminous C, although 10 of the samples were high-volatile C bituminous. The coalbeds varied in thickness from 4.5 to an unknown thickness greater than 67.5 feet.

Jan 1, 1971

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Recently, a collection of programs that will simulate a ventila¬tion system with extensive analyses and report-generating capabilities and error diagnostics has been developed (Didyk, 1974). It has pro¬visions to handle air injections, methane or gas emissions, and leakage. Additionally, it will solve problems where fixed and/or maximum air quantities are specified for some airways. Finally, the simulator has been structured to be extremely modular so that additions and revisions to the model can be easily made. The general aspects of the information flow and logical structure of the mine ventilation simulator are shown in Figure 14. The output from the methane emission model is input into the ventilation simulator for calculation of the concentrations in all branches of the network. The methane model and the ventilation simulator provide powerful tools for the analysis and planning of mine ventilation systems. INPUT DATA REQUIREMENTS In all of the mathematical models, several coefficients that de¬fine the characteristics of the ventilation system are used. For the ventilation simulator, these include the frictional characteristics of the ventilation regulatory devices. Considerable work has been done on the experimental determination of these coefficients for smooth pipes and well-defined mediums, but only limited data are available for actual mining conditions. FRICTION FACTORS: The frictional characteristics of mine airways affect both the dispersion of pollutants and air flow through the roadways,. They

Jan 1, 1975

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 2 Program Use Instructions necessary to execute the program, after the card deck has been prepared, are summarized in the following. B 2. 1 Input Data Format Input data is supplied to the program in two ways a. By data cards that are read in after program compilation. b. By data specifications that are included within the program.

Jan 1, 1976

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

This report was prepared by The Pennsylvania State University under USBM Contract No. H0133040. The contract was initiated under the technical direction of PMSRC, with Mr. Edward D. Thimons acting as the technical project officer. Mr. Frank Naughton was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June 30, 1973,to June 30, 1977. This report was submitted by the authors on August 31, 1977.

Jan 1, 1977

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. Gilsonite, a solidified hydrocarbon, found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), by Ziegler Chemical and Mineral Corp., and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT.

Jan 1, 1984

By Fred C. Turin, Kim M. Cornelius

Work in underground coal mines is repetitive and physically demanding. Workers commonly report a wide range of aches and pains. Management at one mine was concerned about increased reporting of aches and pains by roof bolting machine operators. An analysis of roof bolting tasks was conducted at this mine to identify early warning signs of cumulative trauma. Health and safety risk factors were identified and recommendations to reduce cumulative trauma exposure were provided. Recommendations addressed job procedures, equipment design, and worker awareness of risk factors.

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber predominating. Wood lagging and timber, wires and cables, brattice cloth, hose, paper products, cardboard cartons, and wooden containers are additional combustible materials commonly found in underground storage areas. Shorted or overloaded electrical cables, worn sockets and plugs, spontaneous combustion, careless smoking, and welding and cutting are common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning and to extinguish fires that originate in underground storage areas.

Jan 1, 2011

By Robert A. Bruce

A motion transducer based on coherent mixing of laser light backscattered from rough surfaces is evaluated in terms of sensitivity, bandwidth and range. Tests made with a prototype composed of a 4-mw HeNe laser, a silicon avalanche photodiode, and a 15-cm aperture telescope demonstrate that remote measurements with reasonable bandwidth and accuracy are feasible at distances up to 100 meters.

Jan 1, 1977

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A National Institute for Occupational Safety and Health’s (NIOSH) mine fire detection re-search project was undertaken to evaluate multiple mine fire sensor types for nuisance alarm discrimination. The response of multiple fire sensor types to three small coal fire and three small conveyor belt fires in the presence of diesel emissions was evaluated in NIOSH’s Pittsburgh Research Laboratory (PRL) Safety Re-search Coal Mine (SRCM). An array of fire sensors which included an optical and ionization smoke sensor, a chemical cell CO sensor, and Metal Oxide Semiconductor (MOS) sensors, was used to sample the diesel engine and fire source emissions. The mine fire detection experiments demonstrated the ability of a MOS sensor with a bimodal response to NOx and products-of-combustion (POC) to respond to the onset of smoldering combustion in the presence of CO and POC particulates from a diesel locomotive. As part of an in-mine evaluation in an operating coal mine, the MOS NOx responsive sensor and an ionization smoke sensor was demonstrated as a method to discriminate diesel emissions and cross-interference of H2 on a CO chemical cell fire sensor at a battery charging station. The reinforcement of mine fire sensor information with the use of multiple sensor types, such as an MOS sensor and ionization and optical smoke sensors, is shown to be important for nuisance alarm discrimination and early mine fire detection.

Provide guidance on the selection of millisecond initiator delays between blastholes in surface mine blasting to provide a desired degree of rock fragmentation consistent with safety and vibration considerations. The Problem Blasting remains the primary means of fragmenting, rock for all kinds of mining, quarrying, construction, and excavation activities, and it is the only practical and economic method of breaking up and moving large amounts of material such as coal overburden and stone aggregate. Because of the large amount of blasting done, typically using 4 billion pounds of explosive to break about 8 billion tons of rock annually in the United States, a small improvement in blasting performance will have a significant productivity impact. Standard blasting practices involve the selection of time delays in a blast for at [cast three purposes: (1) to control energy flow to minimize adverse vibrations, (2) to provide sufficient time relief for good rock displacement, appropriate muck pile shape for digging, and the prevention of collar violence, misfires, and flyrock, and (3) to provide an appropriate amount of interhole stress wave and gas pressure action for a desired fragmentation size distribution. Timing guidelines that exist are based on subjective observations rather than measurements, even for the relatively new casting methods. Until this Bureau study, no definitive analysis had been done to quantify the fragmentation and productivity of full-scale blast rounds as functions of precision delay timing.

Jan 1, 1989

Provide the mining industry with an easy-to-use means of accurately predicting surface subsidence caused by longwall mining in the northern Appalachian Coal Basin. Approach The Bureau of Mines developed a subsidence prediction model using the novel approach of a variable subsidence coefficient. This approach had to be used because of the resistant strata types which commonly occur within the relatively thin overburden material typical in northern Appalachia. Such resistant strata precluded the use of the popular European methods that assume homogeneous overburden or overburden behaving as homogeneous from a subsidence point of view. The model is available in a BASIC computer program for use on most personal computers. The user has the options of obtaining individual subsidence calculations or may choose to develop a subsidence profile using an average overburden value. The program output can be generated in graphic or tabular form showing the location of the surface point with respect to the longwall panel edge, overburden depth, and the subsidence value.

Jan 1, 1986

By C. L. Wright

In 1904 the Government began a series of fuel-testing investiga- tions at its fuel-testing plant at St. Louis, Mo. These investigations, which were placed under the supervision of the United States Geo- logical Survey, included chemical analyses, steaming tests, gas- producer tests, briquetting tests, coking tests, and washing tests of samples collected from the various coal fields of the country. The specific purpose of the investigations was to analyze and test the coals and lignites in the United States, in order to deternime their fuel values and the most efficient methods of utilizing them for different purposes. Part of the fuel-testing plant, including the briquetting equipment, was moved to Norfolk, Va., in 1907, and the fuel-testing investiga- tions were made one of the divisions of the technologic branch of the Geological Survey. In 1908, after the close of the Jamestown Exposition, most of the fuel-testing equipment was removed to its present location at the Pittsburgh experiment station, Fortieth and Butler Streets, Pittsburgh, Pa. In 1910, an act of Congress, effective July 1, established the Bureau of Mines in the Department of the Interior and authorized the transfer to this bureau of the fuel-testing investigations that had been carried on by the technologic branch. Bulletins presenting the results of various inquiries and investiga- tions relating to briquetting have been published by the Geological Survey and the Bureau of Mines. As the supply of some of these bulletins is exhausted, the Bureau of Mines has decided, instead of reprinting them, to publish the more important facts they contain

Jan 1, 1913

By R. C. Buehl, J. P. Riott, M. B. Royer

Sponge iron is the metallic product resulting from the reduction (removal of combined oxygen) of iron ore or other iron oxides at a temperature below the fusion point of iron. It has been used for many years in the production of certain grades of high-quality steel, such as tool and cutlery steels. The sponge iron available commercially in limited quantities for such use was produced from high-grade ores that were almost free from the contaminating elements that are generally considered detrimental to the production of certain grades of carbon tool steel. Interest in sponge iron as a scrap substitute was revived when World War II began, when the serious shortage of scrap metals for use in the production of armament caused great concern as to whether steel production could be maintained at the rate necessary for vigorous prosecution of the war effort. Also, because of the severe shortage, steel manufacturers…

Jun 1, 1947

By John T. Aydelotte, Martin J. Gavin

" Oil shale contains little or no oil as such , but it contains an organic material from which oil may be produced by destructive distillation" . This statement , or others conveying the same meaning, appears in many popular and techni cal articles on oil shale . It is based on the belief that the ordinary solvents of petroleum have but little action on the organic substances contained in oil- yielding shales , although on distillation these same shales may yield upwards of 50 gallons of crude shale oil per ton . A 50 - gallon shale thus yields by distillation 18.73 per cent of its weight as oil ( assuming the specific gravity of the oil to be 0.900 ) , although only a relatively small part of this can be recovered by extraction with such solvents as chloroform , carbon tetrachloride , and the like . In the course of certain experiments designed to determine the solubilities of different shales after they had begun to yield oil by distillation , it was found desirable to determine the quantity dissolved from certain unheated shales by various solvents , at or near the boiling points of these solvents . The method used and results obtained are presented below. These experiments were made in connection with the oil - shale investigations being conducted by the U. S. Bureau of Mines , in cooperation with the States of Colorado and Utah .

Jan 1, 1922

By Mark Colwell, Russell Frith

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coal fields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwallface. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 5, 1999

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970