Search Documents

By R. S. J. Toit

Discussion: T. L. Gibbs,* (Honorary Vice-President and Fellow): In terms of the Pneumoconiosis Compensation Act of 1962, a Pneumoconiosis Risk Committee was established whose function it is to estimate (by whatever means the committee deems fit) in respect of every controlled mine the pneumoconiosis risk to which persons employed in a dusty atmosphere at that mine are exposed. In estimating such risk the committee may estimate different risks in respect of individual mines or parts of mines or classes or groups of mines or occupations or localities at mines. The pneumoconiosis risk may be reviewed and re-estimated at any time. The Act provides further that the General Council for Pneumoconiosis Compensation shall apportion the levy imposed on owners of controlled mines on the basis of the pneumoconiosis risk determined by the risk committee and the numbers of persons employed in a dusty atmosphere. The task of the risk committee is a most responsible one and also a very difficult and complex one in view of the many different types of mines, rock formations, dust conditions, etc. Quite obviously, comparisons between mines cannot be made on dust concentrations alone as different mineral dusts have different toxicity or pneumoconiosis response factors. However, with its present knowledge, the risk committee is satisfied that the risk at mines, other than coal mines, is related to the mean quartz-equivalent dust concentration to which persons are exposed and the estimation of risks is based on this relationship. From the above, it will be clear that the work done by Dr du Toit on the problem of basing the current rate of levies to provide for pneumoconiosis compensation on the current dust hazard at mines has been of immense value to the risk committee. Up to now the risk committee has not been able to obtain complete and accurate information on the dust exposure of persons at all mines - and, in fact, it is doubtful whether it will be economic or practicable to obtain this in the foreseeable future - but reasonable assessments have been possible from routine dust sampling in some cases and from periodic comprehensive dust surveys in others. As a temporary measure the risks of some mines were estimated initially on a group basis relating to average dust conditions and the type of rock and mineral mined, but as more information became available, differentiation between individual mines became possible. It is the aim of the risk committee to eventually apply such a differentiation in all cases and to ensure that within the bounds of practicability each mine pays for its risk and for its risk only. In this connection, the relationship between the levies and the amounts actually paid out in compensation are examined regularly. In conclusion, I wish to add my congratulations to the author on his excellent paper. His findings will assist materially in the just administration of that very important piece of beneficial legislation, the Pneumoconiosis Compensation Act. G. K. Sluis Cremer MD (Visitor): Dr du Toit has made a valiant attempt to relate dust hazard and the rate of collecting funds for the purpose of paying compensation for Pneumoconiosis. In doing so he has had to make a number of assumptious, some of which touch on the medical aspects of pneumoconiosis. It is worth discussing whether these assumptions are justifiable. Pneumoconiosis is defined in our Pneumoconiosis Act as permanent disease of the cardio-respiratory organs which is caused by the inhalation of mineral dust. To a non-medical person this definition has probably a clear cut meaning. The doctors however have to deal with such conditions as silicosis and asbestosis where there is a well defined dose response relationship to the inhalation of quartz and asbestos respectively and on the other hand chronic bronchitis where the relationship to dust inhalation is poorly defined and where certainly no clear dose response relationship has emerged after many investigations in this country and overseas. Nevertheless since 1953 about half of our certifications for Pneumoconiosis are on the grounds of chronic bronchitis i.e. the X-rays show no evidence of silicosis, asbestosis or other relevant disease. This fact must affect Dr du Toit's computations. The next assumption we should examine is the manner in which toxicity factors have been allocated to the various mineral species. These allocations have in part been based on a restricted number of animal experiments carried out overseas but mostly in South Africa by Webster at the Pneumoconiosis Research Unit. To extrapolate the findings in a relatively small number of animal experiments to the expected reactious in man is a notoriously dangerous exercise. Furthermore the bracketing together of all silicates (except asbestos) and the insoluble metal oxides is entirely unacceptable. Talc (a hydrated silicate of magnesium) and muscovite mica (a silicate of aluminium and potassium) cause pneumoconiosis in their own right. On the other hand

Jan 3, 1970

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

British Mining Fields, by J. E. Metcalf. Published by the Institution of Mining and Metallurgy, London, 1969. Price 50s. (Students, 30s.). A 100 years or so ago Britain's mining industry led the world in the production of coal and base metals. Although she still maintains a sizeable-and, under the circumstances, remarkably progressive-coal mining industry, her production of most other base minerals has long since been dwarfed by mining fields in the Americas Africa, Australia and the U.S.S.R. Nevertheless the story of mining in Britain is of wider interest than the present scale of operations there might suggest, if only because the domestic British mining industry has in terms of finance, technology and manpower been the fons et origo of many highly productive mining fields outside Britain, including the Witwatersrand goldfields. British Mining Fields was published by the Institute of Mining and Metallurgy to give delegates attending the Ninth Commonwealth Mining and Metallurgical Conference a succinct account of mining in Britain. The main emphasis is on underground mining of base minerals-treated regionally-with separate chapters on coal and gypsum. The author strikes an admirable balance between historical aspects, geological origin and environment of ore deposits, mining methods and economic factors, and provides a few key references for those who wish to make deeper studies. This is exactly the sort of booklet one often wishes were available on South African mining.

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By K, J. MAUNDERS

This paper briefly describes a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25 000 to 70 000 tons of uranium, proves to be very data-sensitive.

Jan 1, 2014

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By E. J. Maunders

This paper describes briefly a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25000 to 70000 tons of uranium, proves to be very data-sensitive.

By I. Wayland

Value added blasting is a process methodology that links tasks and processes, with the aim to improve/enhance the technical application of explosives technology and initiating systems, resulting in improved output. The phases and steps of a typical value added blasting intervention are discussed in this paper. Each step having distinct purposes, principles and methodology. The underlying philosophies and process steps of the programme are described for each step. This paper gives an account of projects that have been completed in two Anglo American Gold Mines. This will include a description of the projects that were conducted at Vaal Reefs 8 Shaft and Western Deep Levels South Mine covering: ? The need for blasting improvements ? The approach that was followed ? The result of the programme.

Jan 1, 1999

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

By F. H. Deist, H. D. Small, J. D. Austin, L. F. Duvel

The development and application of a computer system to aid in the planning of production in mines by F. H. DEIST, L. F. DUVEL, J. D. AUSTIN, and H. D. SMALL Published in the Journal, December 1972. Discussion by J. W. WILSON and R. W. HAZELL Although the Mine Planning Simulation Programme was originally developed as an aid to coal-mine planning, its extreme flexibility has enabled us to simulate gold-mine planning with equal facility. The initial application of the Mine Planning Simulation Model was in a small area of a large Free State gold mine where the primary aim was to assess the applicability of the programme to the gold-mining situation.

Jan 12, 1972

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

The 90th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 19th August, 1987. Dr H. Wagner (President) was in the Chair and declared the meeting open at 16h00. Obituaries The President read out the names of the departed Members as follows: N.M. Airey, F.J. Kisbey-Green, Dr R.A. Pelletier, C.B. Anderson, A.R. Cator, J. van Heerden, P.J. Burman, C.C. Crosson, M. Livingstone¬Blevins, S.T. Firman, V.E. Kisbey-Green, and A.L. Corna. All stood and observed a moment of silence as a mark of respect. Minutes The minutes of the 89th Meeting of the SAIMM, which was held on 20th of August, 1986, were confirmed.

Jan 1, 1987

Council for 1998/99 President R.P. Mohring President Elect J.R. Dixon Vice Presidents Senior M.H. Rogers Junior Dr L.A. Cramer Immediate Past President Dr N.A. Barcza Honorary Treasure J.A. Cruise Members of Council J.P.W. Bennie E.G. de Villiers A.A.B. Douglas F.M.G. Egerton R. Graham Dr R.G. Gürtunca Dr R.V.R. Handfield-Jones P.J. Knottenbelt R.G.B. Pickering* P.S. Piper Prof. R.F. Sandenbergh Dr T.R. Stacey D.J. van Niekerk P.J. Venter J.C. Viljoen

Jan 1, 1998

By T. P. Katakwa

The utilization of software is now inherent to virtually every activity along the mining value chain. However, apart from the software survey done by Gibbs in the 1990s and work on the extent of diffusion of information and communication technology (ICT) in the South African platinum sector by Mugodi and Fleming in 2003, the nature and extent of software utilization in the South African mining industry has never been evaluated. The Mine Planning, Optimisation and Valuation (MPOV) Research Group in the School of Mining Engineering, University of Witwatersrand, therefore initiated a project to collate and analyse the current utilization of software in the South African mining industry. This was done through the development of a web-based database of the relevant software. Snowball sampling was used to collect the data because the South African mining industry is diverse and software utilization is fragmented across and within the sectors of the industry. The data was then organized into distinct categories so that the information from a variety of sources could be evaluated on the same basis. A beta version of the database can be accessed online through a user-friendly front-end platform at http://db.mining.wits.ac.za. The database is expected to help at least 13 educational institutions with decisions on facilities and training that are vital to the education of mining and mining-related professionals. Exploration, mining, and consulting companies will also benefit from information in the database relating to availability and useful combinations of software solutions. The database is also strategic to software providers by providing a better understanding of their respective relative market share along the mining value chain. An analysis of the data collated in this research shows that about 77% of the software users are mining companies, 17% are consulting companies, 3% are mineral exploration companies, and the rest are software providers and educational institutions. The software used in the South African mining industry is largely provided by Gemcom Software International, MineRP Solutions, and MRM Mining Services. CAE Mining, who in 2010 acquired the Datamine Group providing Datamine software, is also widely acknowledged as a major software supplier in South Africa, but data from them had not been obtained at the time of producing the beta version of the database due to proprietary constraints. The work reported in this paper is part of an MSc research study in the School of Mining Engineering at the University of the Witwatersrand. Keywords mine planning, mining, value chain, software, database, South African mining industry, utilization.

Jun 1, 2013

By C. L. M. Gough, L. A. Vermeulen, D. D. Howat

Formulae expressing the dependence of the mass of a grinding ball on the amount of material milled by a ball mill are derived. It is shown that, with the aid of these formulae, it is relativel rsimple for the results of a marked-ball test to be analysed and for the relative performance and cost-effectiveness 0 the various types of ball under test to be evaluated. Predictions based on theory and the results obtained in a marked-ball test in a ball mill are compared detail and shown to be in close agreement. The difficulties associated with marked-ball tests are considered, and an explanation for the decrease in the calculated consumption of the balls, which follows naturally from the theory, is presented. The marked-ball anomaly explained, and it is demonstrated that the ball consumption in a ball mill can be predicted with fair accuracy from the results of a marked-ball test.

Jan 1, 1983