Search Documents

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By G. Akdogan, I. Mwandawande, S. M. Bradshaw, M. Karimi

The mixing characteristics of industrial flotation columns were investigated using computational fluid dynamics (CFD). Particular emphasis was placed on the clarification of the relationship between the liquid and solids mixing parameters such as the mean residence time and axial dispersion coefficients. The effects of particle size and bubble size on liquid dispersion in the column were also studied. An Eulerian-Eulerian method was applied to simulate the multiphase flow, while additional scalar transport equations were introduced to predict the liquid residence time distribution (RTD) and particle age distribution inside the column. The results obtained show that particle residence time decreases with increasing particle size. The residence time of the coarser particles (112.5 μm) was found to be at least 60% of the liquid residence time, while the finer particles (19 μm) had a residence time similar to the liquid. The results also show that an increase in the particle size of the solids results in a decrease in the liquid vessel dispersion number, while a decrease in the bubble size increases liquid axial mixing. Finally, the simulated axial velocity profiles confirm the similarity between the liquid and solids axial dispersion coefficients in column flotation.

May 2, 2022

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By L. M. Tavares, T. M. Campos, P. M. Faria, R. M. Carvalho

Recent advances in mechanistic ball mill modelling are expected to allow for more accurate predictions that overcome the well-known limitations of phenomenological approaches, including their inability to predict the effect of liner geometry and their wear, in grinding. Although able to describe continuous operation, the UFRJ model of ball mills has only been validated in the past in mills that operate in batch mode, either in laboratory or pilot scale. The present work demonstrates the application of the mechanistic UFRJ ball mill model to predict fine grinding of iron ore in a pelletising plant in Brazil, the first application of such a mechanistic modelling in continuous mode. It shows that the model provides accurate descriptions of flows after iterations in a closed-circuit with hydrocyclones. Keywords: Ball mill, iron ore, grinding, modelling, particle breakage

Jan 1, 2020

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By Yuandong Qiao, Erdong Li, Chao Lv, Junjian Ye

The gas-based CO reduction of Panzhihua vanadium titanomagnetite concentrate from 1100°C- 1250°C was investigated in this paper. The reduction degree increased with increasing temperature and increasing reduction time. At a temperature of 1250°C and a reduction time of 20 minutes, the metallisation degree reached 92%. The iron-titanium oxide phase transformation during reduction process was Fe2.75Ti0.25O5→Fe2.5Ti0.5O4→FeTiO3→FeTi2O5 according to the X-ray diffraction analysis. The SEM and map scan by energy spectrum of results of reduced samples at different temperatures indicated that the metallic iron particle size increased gradually as the reduction temperature increased. These results can serve as a reference for the reduction of vanadium titanomagnetite by CO. Keywords: Vanadium titanomagnetite concentrate, CO reduction, phase transformation, reaction mechanism

Jan 1, 2020

By J Taguta, B. McFadzean, P. E. Ngoepe, M. G. Mulaudzi

Computational modelling methods and isothermal titration calorimetry (ITC) were employed to investigate the interaction of a pyrite surface with thiol collectors. Modelling work was conducted in the presence and absence of water. Microcalorimetry was employed to investigate the resultant energy of interaction pyrite as a result of mineral-collector interactions. Sodium ethyl xanthate (SEX), diethyldithiocarbamate (DTC) and diethyl dithiophosphate (DTP) were investigated in this study. The results showed that the calculated surface energies and morphologies for FeS2 showed that (100) and (111) are the most stable surfaces. The morphology also indicated the appearance of the (100) and (111) surface facets and no presence of others. The calculated adsorption energies between thiol collectors and the pyrite surface were always more exothermic than the experimentally determined ones. When comparing different ligand types with the same alkyl chain length, the heat of adsorption of diethyl-DTC was greater than that of ethyl xanthate and diethyl-DTP for pyrite. Experimentally, the diethyl DTP barely adsorbed onto the pyrite surface and this may be due to a different mechanism of action. In computational calculations, water adsorption was found to reduce the reactivity of the Fe atom for the interaction with thiol collectors, and bring the adsorption energies closer to the magnitude of the experimental values. Keywords: Computational modelling, microcalorimetry, experimental and thiol collectors, adsorption energies

Jan 1, 2020

By N. C. Joughin, H. Wagner

Research is a business activity, and is as different from other business activities as banking is from mining. attempting to use research to solve their problems, managers do not always recognize its unique features, are frequently disillusioned with the outcome. With a view to enabling managers to use research more effectively, an outline is given of the features of research as applied to mining. Types of research are distinguished, and stages in the research-and-development process are identified. The time-scales and resource requirements of the various types and phases of research are explained. Examples of research that have reached implementation in gold mining are given to illustrate the features mentioned. Practical and economic considerations are discussed, and pitfals and recommendations in the use of research are highlighted.

Jan 1, 1989

By M. H. Tyeb, C. Banerjee, A. K. Majumder

The primary requirement from a hydrocyclone is the classification of the feed solid particles. Particle classification occurs inside a hydrocyclone by virtue of the relative radial distribution of the suspended particles, based on their size and specific gravity. The particle classification behaviour in a hydrocyclone is experimentally studied in this paper. The phenomenological features of the air core at different feed solid concentrations and the distribution of the solid concentrations in the hydrocyclone are also analysed by the theoretical study of flow features in a steady Rankine vortex. Semi-empirical models for predicting the hydrocyclone performance in terms of flow split ratio, and cut size have been developed using the background knowledge of convoluted hydrodynamics. In addition, to validate the classification performance of a smaller diameter hydrocyclone, the potential of the present model is extended for envisaging the same for larger diameter hydrocyclones. A comparison between the model predicted values and the measurement data shows a good match. Keywords: Hydrocyclone, classification, Rankine-vortex, air core, modelling

Jan 1, 2020

By A. Navarra, A. Quelopana

The mine production scheduling problem (MPSP) has been studied since the 1960s, and remains an active area of computational research. In extending the concepts of the MPSP, the automated mine may now be regarded as a hierarchical intelligent agent in which the bottom layer consists of distributed robotic equipment, while strategic functionality occupies the higher layers. Here we present a disambiguation of artificial intelligence, machine learning, computational optimization, and automation within the mining context. Specifically, the Q-learning algorithm has been adapted to generate the initial solutions for a high-performing strategic mine planning algorithm, originally developed by Lamghari, Dimitrakopoulos and Ferland, based on the variable neighbourhood descent (VND) metaheuristic. The hierarchical intelligent agent is presented as an integrative conceptual platform, defining the interaction between our new Q-learning adaptation and Lamghari’s VND, and potentially other hierarchically controlled components of an artificially intelligent mine, having various degrees of automation. Sample computations involving Q-learning and VND are presented.

Dec 1, 2021

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By N. Wagner, P. den Hoed, J. D. Steenkamp, S. Soqinase

In pyrometallurgical processes, metal oxides are reduced from molten slag through carbothermic reduction. It is of interest to evaluate the reactivity of the carbonaceous materials towards substances such as slag. Characterization techniques such as coal petrography can provide insight into the influence of feed coal properties and how they potentially dictate reductant performance. This study aimed to compare the petrographically determined organic composition of coal to reductant reactivity. Two South African medium-rank C bituminous coals and one anthracite sample were investigated together with high-carbon ferromanganese industrial slag. The reductant reactivity tests were conducted at 1500°C in a muffle furnace to assess the potential of carbonaceous reductant in reacting with the main slag components. SEM-EDS was applied to understand the extent of MnO (and to a lesser extent, SiO2) reduction from the slag. Coal 2, consisting of a greater proportion of vitrinite (59.5 vol% on a mineral matter-free basis and 54.7 vol% including mineral matter) was the most reactive reductant. The anthracite sample, with the highest inert maceral proportions (71.8 vol% including mineral matter and 76.8 vol% on a mineral matter-free basis), was the least reactive reductant.

Feb 6, 2023

By T. Wallmach

Heavy mineral deposits are a source of the economic important element titanium, which is contained in minerals such as ilmenite, pseudorutile and rutile. In the Ranobe heavy minerals deposit these minerals occur not only as primary unaltered minerals but also display various degrees of alteration resulting in an increased titanium content of the deposit. The presence of the various FeTi-oxide minerals? textural relations is a reflection of geological processes and may ultimately be used to unravel the geological history of the deposit. These minerals have different chemical and physical properties that influence metallurgical tests and the quality of products produced from various mineral beneficiation streams. It is therefore of metallurgical importance that the minerals are well characterized, defined and monitored during preliminary beneficiation tests.

Jan 1, 2007

By B. Rezai, Z. Pourkarimi, M. Noaparast, S. Chehreh Chelgani

Nanobubbles (NBs) flotation separation can be an indicator for improving the efficiency of fine particles through the conventional process. Since flotation reagents such as frothers can reduce bubble size, they can potentially be used for the generation of NBs and develop a selective NB flotation separation. This study explored the flotation separation of fine phosphate particles from their associated minerals in the presence of NBs, which were generated by using a phosphate flotation reagent (Flo-YS: collector-frother). The results of flotation tests showed that in the presence of NBs, the flotation efficiency was significantly improved. However, in the presence of NBs, surface chemistry analyses (Fourier Transform Infrared Spectroscopy and High-Performance Liquid Chromatography) illustrated that the collector adsorption on the surface of phosphate particles decreased. A comparison between outcomes of various phosphate flotation conditions indicated that increasing the flotation efficiency in the presence of NBs may be due to the aggregation of fine particles by the generated NBs, and also selective adsorption of NBs (hydrophobisation) on the surface of particles. In other words, generating NBs by selective collectors may increase efficiency and decrease the collector consumption of a flotation process. Keywords: Phosphate, selective separation, fine particles, collector-frother, efficiency, mechanical flotation cell

Jan 1, 2020

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors' implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By D. Bessinger, N. Rughubir

Exxaro Sands KZN produces?among other heavy mineral products?high titania slag, which is used as feedstock to the pigment industry. The titania slag is produced from the smelting of ilmenite in two 36 MW DC furnaces. In this smelting process carbon monoxide gas is produced. This gas is cooled, scrubbed and washed to remove entrained dust. This paper provides details on the gas cleaning plant system and the chemistry, mineralogy and size distribution of the particulate material contained in the off-gas stream. Characterization of the dust shows that is consists mainly of ilmenite, but with relatively high levels of SiO2and MnO. Smelting of the dust in a 500 kW DC furnace was carried out to investigate the potential for recovering valuable elements from the dust.

Jan 1, 2007

By N. K. Singh

The calculation of resource volumes for large mineral sands deposits is the process of systematically compiling all known data in order to define the volume of ore contained and its intrinsic economic value. Traditionally, this process has been highly speculative in nature, as the variability of the layer thickness, even between closely spaced, boreholes can be highly variable. The issue of horizon continuity is of critical importance in mine modelling and resource definition. Accurate volume estimates are difficult to derive from drilling data alone, as the borehole spacing of an economically viable drilling programme is often greater than the spatial frequency of the variations in profile thickness. The limitations associated with this inferential approach to resource estimation can be mitigated through the use of newly developed ground penetrating radar (GPR) methods, thereby maximizing orebody optimization by reducing contamination and orebody loss. The use of GPR in the mining industry has historically been limited to shallow, high-resolution applications, such as the location of voids in limestone or the mapping of paleo channels for alluvial gold and diamonds (Francke and Yelf, 2003). These limitations have not been technology based, but rather market based, as the vast majority of GPR systems were originally designed for civil engineering applications. A new generation of GPR technology, designed specifically for maximum penetration in sand environments, is now being developed. This technology has been trialled extensively at the Richards Bay Minerals heavy mineral sand deposit in South Africa with optimistic results. The clay base of the mineral sands has been imaged to some 120 metres. Further equipment refinements are expected to yield even deeper profiling and higher resolution. The resolution offered by this technology is unique, allowing individual depositional sequences to be imaged and modelled in three dimensions. This paper will discuss the advances in GPR technology relevant to the mineral sands industry, as well as methods to optimize and integrate GPR data into existing mine models. Also addressed will be approaches to three-dimensional modelling of high-resolution GPR data and subsequent volume estimations.

Jan 1, 2007

By R. D. C. Shone

Consideration is given to the technical and economic feasibility of freeze desalination as a technique for the simultaneous provision of ice to cool deep mines and for the desalination of mine water. Freeze desalination has not been developed fully or commercially. For sea-water applications, it may not offer significant advantages over other methods of desalination but, for the unique mining application, a single dual purpose plant that produces desalinated ice could offer significant cost savings over combinations of separate desalinators and ice-makers. The current status 01 freeze desalination is reviewed, and the important aspects relating to mines are discussed. Some freezing processes that could be suitably modified are described. The possible use of conventional ice-making machines for desalinating mine water is also discussed.

Jan 1, 1987