Search Documents

By A. M. Copeland, A. J. Barrett

The use of hydraulically placed backfill in the deep gold mines of South Africa has increased rapidly over the past decade. The backfill that is delivered to the placement areas has a relatively high moisture content, and it is therefore pumped into geotextile containment bags that allow excess water to drain out but retain solid particles. The specific problems associated with this process that are addressed in this paper include the loss of solid particles entrained in the excess water, the rate of strength gain of the backfill, and the post-placement shrinkage of the backfill. The results of laboratory, surface stope, and underground tests are described. The parameters that were varied included the slurry density, the particle-size distribution, and the feed rate of the slurry the concentration of added flocculant; and the type of geotextile used as containment. Suggestions are given for the optimization of the placement properties of backfill.

Jan 1, 1994

By N. Kernahan, T. Zaniewski

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Sep 1, 2001

"Chairman: Mr R. A. PLUMBRIDGE Rapporteur: Dr D. M. HAWKINSPapers:The relevance of computer methods to the economics of the mineral industry by R: A. PerlmanDynamic control of a mining enterprise by R. G. CoyleAn economic model of the mineral sands industry by G. P. A. HoweMr M. Splaine, in opening the discussion on Mr Perlman's paper, asked whether the model, as fitted by data up to 1963, predicted the rise in the price of copper in 1967, and whether the model could be used to capitalize on short-term price fluctuations.Answering the second question first, Mr Perlman said that the horizon used is six months to one year. In the very short term the activities of speculators obscured the effect of the fundamental econometric variables. This effect, however, was removed if one moved to a longer term, say, quarterly. In 1963 the model had predicted a price rise in 1964 and 1965 and a drop in price in 1966. The rise in 1967 had been caused by a strike, and imponderables such as large strikes were difficult to include in the model since they were unpredictable. Model simulation can be used to show the effect of strikes on price and the effect of small strikes is small.Mr B. R. van Rooyen said that because models are both calibrated and tested on historical data a bias was introduced which gave rise to an overoptimistic estimate of the accuracy of the forecasts. To this Mr Perlman replied that there seemed to be no alternative to the use of historical data for calibrating and testing models, and thus little hope of avoiding the bias. A second point made by Mr. van Rooyen was that manage¬ment tended to be suspicious of complex models and that frequently more heuristic models were sufficiently accurate and preferable for investment decisions. He added that if management were not involved in the model building the econometrician might easily go astray, Mr Perlman replied that symbiosis between data analysts and users of the model was essential and that the experience of the practitioner must be reflected in the model.Mr M. R. Fuller-Good remarked that a clear understanding of future price trends was essential for effective capital planning, and asked, first, how one went from the compiled data on supply and demand to the determination of their effect on price, record, whether necessary data, for example, capacities, could be obtained timeously, and, third, when strikes restricted supply, whether stockpiling by consumers induced large price fluctuations."

Jan 1, 2014

By A. L. Hinde, A. A. Bradley, K. H. Stanton, P. J. D. Lloyd, G. K. Schymura

As part of its programme to develop methods for concentrating minerals underground, the Chamber of Mines of South Africa in conjunction with Lurgi evolved and tested a I MW centrifugal mill. The machine is capable, in the autogenous mode, of grinding more than 25 t/h of minus 75 plus 44 mm hard quartzite to a minus 3 mm product containing over 50 per cent minus 75 µm material, and as a ball mill of grinding more than 60 t/h of minus 19 mm quartzite to a minus 3 mm product containing over 35 per cent minus 75 µm material. Extrapolation of computer models of the process suggests that these limits can be comfortably exceeded. Long-term continuous testing is in hand, aimed at proving that this I m in diameter by I m long mill is in every respect the equivalent of a conventional 4 m by 6 m ball mill.

Jan 1, 1982

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By J H. Sullivan

Contents Background information Locality of Kumba?s Iron Ore Mines Sishen?s Product Specifications Geological Description of boreholes Sample Preperation Block delineations Production Geology Process Laboratory information Turnover times reached Inter Laboratory Comparisons Quality control activities in lab Purpose of laboratory Results attained Standard samples Monitoring of processes with QA/QC standards Mean paired difference of duplicates Duplicate samples Conclusion

Jan 1, 2005

By W. Bleloch

Published in the Journal, September 1970, and presented at a colloquium on 'Future of the Steel Industry', 17th March, 1971. Errata (a) The final sentence in the penultimate paragraph, left hand column p. 34 of the text should read: 'In the hot regions of the bosh and stack the C+CO2=2CO reaction proceeds to CO from coke carbon and carbon dioxide generated by reduction of iron oxides by CO (the so-called solution loss of carbon)'. The italicised words have been omitted in the text. (b) Temperature in Fig. 3 is K not C. (c) In Fig. 9, connection from top plate of column 10 to heat exchanger 9 has been omitted. DISCUSSION J. B. BEEDON AND C. J. JONKER* Dr Bleloch's paper has outlined the advantages of recycling stack-gas of low nitrogen content in the blast furnace. In the first instance it would appear to be extremely beneficial in controlling the hearth temperature and allowing a 100 per cent oxygen-blast to be used. On a second point however we have to disagree. It is claimed that heat is liberated in the combustion zones by the oxidation of CO to CO2 near the tuyeres and in the subsequent reduction of the CO2 by CO. The author has hypothesized as follows, and we quote: 'The C+CO2=2 CO reaction in the outer combustion zone at about 1 700°C is no longer endothermic due to loss of stability of CO2 and its consequent dissociation into CO and free oxygen.' This statement requires closer examination. If we consider the individual events occurring with the CO in the recycled topgas, with the oxygen in the blast and with the coke in the burden, as done by Dr Bleloch, the following heat considerations emerge. All heats of reaction are calculated from the enthalpy values of each reactant and product, as well as the temperature dependence of their molar heat capacities. (a) At the tuyeres: CO+1/2 O2-+CO2 . . . . . (1) CO, CO2 at 500°C; O2 at 25°C. ?H reaction = -65 000 cals/mole CO The reaction (1) is exothermic. (b) In the outer combustion zone: CO2+C?2 CO . . . . . . . . (2) C, CO at 1 700°C; CO2 at 500 0C. ?H reaction = -56 000 cals/mole CO Reaction (2) is endothermic. The overall heat gain of reactions (1) and (2) is ?H=+56 000 - 65 000= -9000 cals/mole CO i.e. the overall reaction is slightly exothermic, the amount of heat liberated is however smaller than suggested by Dr Bleloch. (c) The dissociation CO2+CO+1/2 O2 . . . . . (3) is a highly endothermic reaction at 1 700 0C, requiring 82 000 cals/mole CO2 to proceed to completion. Furthermore, this reaction (3) is energetically not favoured to proceed, as can be observed from the free energy-temperature relationship of figure (3), which favours the formation of CO2 at 1 700 0C. Hence direct dissociation of CO2 at 1 700 0C appears to be unlikely.* The concept of recycling topgas is however still intriguing from many other points of view. Apart from providing a very efficient method of hearth temperature control, it will create a much higher CO partial pressure in the stack. Whether the rate of indirect reduction in the stack will be proportional to this partial pressure or not is un-

Jan 9, 1970

By D. R. Hardman, J. W. Oberholzer

Based on information supplied by South African collieries to the Coal Mining Laboratory of the Chamber of Mines since 1978, the paper outlines the general performance of the continuous miners used and gives the results more-detailed studies of the cutting, loading, and transportation processes. On average, the continuous miners produced coal at a rate of 76 t per operating hour, which, at an average machine availability of 67 per cent, resulted in a production of 51 t per total hour. The cutting rates varied between and 250 t/h but, owing to machine and system inefficiencies, the overall production rate varied between 92 and 48 It is concluded that, if the collieries concentrated on improving their machine utilization procedures and operating practices, they could increase the overall production from their continuous-miner sections.

Jan 1, 1987

By H. Moslemi

Metal sulphides are usually semiconductor and their electrical conductivity is low; therefore they are sources of electrons and promote electrochemical reactions. This phenomenon is of significant importance in sulphide flotation. The formation of a hydrophobic surface on the sulphide minerals is the result of various electrochemical reactions. Potential difference in the mineral-liquid interface plays an important role in the kinetics of the reactions, and consequently, on the flotation behaviour of sulphides. The value of the potential difference is influenced by different oxidation-reduction reactions at the interface area, and is measured by a two-electrode system in which an electrode is applied as reference electrode. In this study, we attempted to measure open-circuit potentials of pyrite, pyrrhotite, and steel electrodes with respect to the reference electrode. To verify the results, two reference electrodes, saturated calomel and gold, were used. Time-potential relations with respect to both reference electrodes show that the potential of both pyrite and pyrrhotite increases with time; however, this trend decreases for steel except when at pH 12. The results show a potential drop by an increase in pH value, except for steel, for which the opposite holds. This paper discusses galvanic interactions between minerals and grinding media in the grinding circuits, as well as among other minerals in the flotation processes.

Jan 1, 2012

By B. M. Van Vliet

SYNOPSIS This paper outlines the principles involved in the regeneration of activated carbon for renewed use in the recovery of precious metals or the purification of water. While chemical methods are effective in restoring the activity of spent activated carbon containing only single or defined adsorbates, thermal methods have to be used when the spent carbon is loaded with a heterogeneous mixture of adsorbates such as those normally present in industrial process streams or effluents. The steps involved in thermal regeneration are described, together with the operating conditions that can be controlled to give the required degree of activation. Finally, an account is given of the structural changes that occur in a new or spent activated carbon during thermal treatment.

Jan 1, 1991

The sixth University of Stelenbosch (US)/University of Cape Town (UCT) Minerals Processing Symposium was held at the University of Cape Town on Friday, 7th August, 1987, and was sponsored by The South African Institute of Mining and Metallurgy (SAIMM). Once again the Symposium attracted a large number of delegates from the mining, metallurgical, and chemical industries. Uranium and electricity A symposium on 'Uranium and Electricity- The Complete Nuclear Fuel Cycle' will be held in Saskatoon, Canada, during 18th to 20th September, 1988. The Symposium is sponsored by the Canadian Nuclear Society. Electric steel The Institute of Metals, organizers of the 3rd European Electric Steel Congress, have announced that this important international event will take place in October 1989 at the Bournemouth International Centre.

Jan 1, 1987

By B. Rainier

This paper discusses the preparation of material for backfilling operations using hydrocyclones. Aspects dealt with include the advantages and disadvantages, material requirements, process constraints, operating systems and equipment of the backfill plant.

Jan 1, 1988

By A. A. Snodgaass

This paper reviews lead as a commodity, starting with a brief historical outline and dealing with the various uses of lead in some detail. It then goes on to discuss some statistics in relation to the production and reserves of lead, before sketching its mode of occurence. The topics are approached in regard both to the world and to South Africa, with the emphasis on the later. The mining and concentration of lead at Black Mountain Mine at Aggeneys in the north-western Cape Province are detailed, before a general account is given of the smelting, hydrometalurgical extraction, and refining of lead, together with the processes used in these activities. The paper concludes with a discussion of safety and health in regard to lead and a brief look at the commodity's future.

Jan 1, 1986

It is almost eight years to the day when we launched the original SAMREC Code in March 2000. Since that date I think the SA minerals industry has matured beyond recognition in its approach to reserve and resource reporting, and I believe we can be justifiably proud of that progress. Many of those companies that have led the way in reporting standards are listed on our sponsors list. We thank them for their sponsorship but even more for their considerable support in all aspects of the SAMCODE organization. Matt Mullins, my co-speaker here today, has been instrumental in the revision of the SAMREC Code over a long period of time and also took up the reigns with the SAMVAL Code after the retirement of Rob Croll. I would like to formally thank Matt for his immense contribution in producing the two Codes; he can take great pride in the final product and fully deserves the many accolades that we have already received from our international counterparts. He has done all this whilst still maintaining a very demanding day job at BHPBilliton. Matt will be the first to admit that he has received tremendous support from more than 100 people who participated in the various working groups, many of whom are employed by our sponsors. There are obviously too many to mention by name but they deserve a big vote of thanks for their personal contributions. In addition to launching the two Codes we are also launching our ?branding? initiative with our own SAMCODE logo and the SAMCODE website: www.samcode.co.za. All the slides used in the presentation today will be on the website later today as will a newsletter which will serve as a media release.

Jan 1, 2008

New Journals The following three journals may be of interest to readers: Fuel Processing Technology, Process Economics International, Speculations in Science and Technology, MM reports Report no. 2016 Analysis of the NIMROC reference samples for majorelements. Report no. 2018 Supergene aUeration of sulphide ores. II. The effect on the floatability of chalcopyrite, galena, and sphalerite. Report no. 2013 List of unrestricted NI M publications issued from 1966 to 1979. Report no. 2014 The determination by spark-source mass spectrometry, of chlorine and phosphorus in high-purity tungstic oxide. Report no. 2017 Vanadium-bearing titaniferous iron ores from the Rooiwater, Usushwana, Mambula, Kaffirskraal, and Trompsburg Igneous Complexes. Report no. 2022 The determination of thallium and indium in sulphide concentrates. Report no. 2023 Atomic-absorption spectrophotometry with hydride generation: an improved technique. Proceedings Proceedings of the Eleventh Commonwealth Mining and Metallurgical Congress, Hong Kong, 1978. London, Institution of Mining and Metallurgy, 1979. 800 pp. 35,00 or $U.S.77,00.

Jan 1, 1979

By C. Musingwini, C. Beaumont

"Kansanshi mine, located in northwestern Zambia, uses conventional openpit mining to produce primarily copper, with gold as a by-product. The ore is extracted from a deposit with highly complex mineralogical suites that are difficult to process, sometimes leading to poor recoveries. The mine was using an ore classification system called ‘Mat-Type’, which classified various ore types into 22 different quality categories, ranging from poor to good quality. Ore with poor recovery was classified as ’poor quality’ ore and directed to long-term stockpiles. Due to a lack of proper integration between the technical and functional areas forming the mine value chain, Mat-Type unintentionally misclassified ore. A geometallurgical analysis was therefore undertaken to review Mat-Type and a new geometallurgical ore classification system, called ‘OXMAT ’, was developed to replace Mat- Type.When implemented, OXMAT eliminated nine of the 22 ore categories and the remaining 13 ore categories could now be more accurately and consistently defined, leading to a significant change in the quantity of ore being mined. OXMAT demonstrated that within a defined test volume of the geological model, waste tonnes could be reduced by 19% while ore tonnes could be increased by 17%. This paper therefore demonstrates the value created through integrated geometallurgical modelling. IntroductionKansanshi mine is located in northwestern Zambia, approximately 10 km north of the provincial capital Solwezi and about 160 km west of Nchanga mine in the Central African Copperbelt (Broughton and Hitzman, 2002). The location of Kansanshi mine relative to other major copper deposits in the Copperbelt is indicated in Figure 1.Kansanshi mine uses conventional openpit mining methods to exploit copper- and gold-bearing veins hosted in a structurallycontrolled mineral deposit. Mining is carried out in two areas of the deposit, the Northwest and Main pits. A third area of the deposit, called Southeast Dome, is currently not being exploited (Figure 2)."

Mar 1, 2019

By A. Buncombe

In March 1984, two years' work by senior metallurgical personnel from the six major mining groups culminated in the formation of the Mine Metallurgical Managers' Association of South Africa. This Association has joined a group of specialist Associations operating within the South African mining industry whose aims are to uphold the standards and promote the interests of their various professions.

Jan 1, 1987

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

By D. B. deur Mostert

This paper was presented at the Coloquium on Management Techniques in the Mining and Metallurgical Industry, which was organized by The South African Institute of Mining and Metallurgy and held in Pretoria during June 1988. The author asks whether technical audits are of any use to management. Technical auditing he defines as an evaluation undertaken by an outsider of whether a technical activity is being carried out correctly. After examining the types of technical auditing, and its prerequisites and procedures, he describes its application in regard to quality, and to production processes and their adequacy. He then answers his question by saying that, not only are technical audits very useful, but they form an essential element in the provision of quality products. In addition, they give management the opportunity of testing whether the activities of the organization are being conducted correctly. This is their most important function in that they alert management to areas of potential growth, modernization, and innovation. However, the use to which technical auditing is put remains the key to its value; that is, its value depends on the positive action that each manager takes as the result of a technical audit.

Jan 1, 1989

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014