Search Documents

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By Jogeshwara Sahu, Sapan Kumar Kandi, SANDEEP KUMAR JENA, Sachida Nanda Sahu, Sarada Prasad Das

The present article reports the recovery of potassium from mica scrap using carbide lime waste and NaCl. The acid leaching of mica [4 M H2SO4 at 90 °C] can recover a maximum of 25% potassium. However, in the chlorination roasting (with CLW and NaCl) water leaching process, it was possible to recover potassium to the tune of 94% [900 °C, 50 min roasting; mica:CLW:NaCl 1:0.75:1]. The formation of water-soluble phase like sylvite (KCl) and water-insoluble phases like anorthite ( CaAl2Si2O8) and nepheline ( NaAlSiO4) confirms the complete breakdown of the mica crystal structure. The extraction mechanism proceeds with the formation of a transition state followed by the release of potassium as KCl. The characterisation studies using ICP-OES, XRD, FTIR and FESEM support the proposed extraction mechanism. The salt produced by the evaporation of roast-leached liquor confirms the presence of sylvite and halite only, which can be separated to get the fertiliser grade KCl.

Sep 29, 2021

By Y. I. Rabinovich, S. C. Brown

In the Florida phosphate industry, fatty acid collectors are used to separate phosphate ore from silica during the rougher flotation stage. However, the presence of multivalent ions (in particular Ca++) in the processing water has been reported to result in the activation of silica with respect to oleate adsorption, rendering it floatable. Hence, adequate separation may not be achieved during the rougher flotation stage. In this study, the direct measurement of surface inter-action forces via atomic force microscopy was used to delineate possible mechanisms for calcium activation under phosphate flotation conditions at oleate/calcium concentrations both above and below the calcium dioleate precipitation limit.

Jan 1, 2004

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By Antonio Rivera

On Nov. 13, 1985, Colombia's Ruiz volcano erupted, killing an estimated 25,000 people and burying several villages. Damages were estimated to be about $US300 million. The following is an account by SME member Antonio Rivera of the volcanic activity that led to the eruption. His account also includes a description of the geography and some geology of the affected area. Mining operations in the area were mostly unaffected, although some operations were forced to close until the roads leading to them could be repaired. Introduction The Ruiz volcano is located on the Central Cordillera of Colombia about 28 km (17 miles) southeast of Manizales, the capital of the state of Caldas. Ruiz is one of nine volcanoes that form a complex volcanic chain within the middle portion of the Central Cordillera. The Cordillera has 30 other volcanoes in the southern part of Colombia. Ruiz volcano Ruiz's elevation is 5200 m (17,060 ft). It is covered by an ice cap estimated to be 20 m (66 ft) thick at its summit, an area that covers 17 km2 (6.5 sq miles). Drainage is composed of several rivers that flow into the Magdalena River on the east and Cauca River on the west. The rivers flowing to the east are Guali, Azufrado, Lagunillas, and Recio. The rivers that flow to the west are Claro, Molinos, and Chinchina. There is a road from Manizales to El Refugio, a ski area located on the northeast flank of the volcano at 4800 m (15,750 ft) in elevation. The Ruiz volcanic complex was built in two stages. The first is a shield type of volcano (mainly lavas) formed about a million years ago. The second is a younger stratovolcano overlaying the ancient one. It consists of lavas and pyroclastics and was built over the past 500,000 years. Twenty-four eruptions of Ruiz are known to have occurred during the last 14,000 years. Its products mainly consist of lava flows, pyroclastic flows, mudflows (lahars), and directed lateral explosions. Historic eruptive record 1595 - Debris avalanche, blast, pyroclastic flows, mudflows, ash flows, and ash fall. 1828-1829 - Ashes (phreatic). 1831-1833 - Gas emissions and ashes. 1845 - Mudflows and pyroclastic flows. 1985 - Sept. 11- Fumarolic activity, phreatic eruption, ash fall, and small mudflows. 1985 - Nov. 13 - Ash and pyroclastic fall, major destructive mudflows (magmato-phreatic eruption). From 1845 through 1984, Ruiz volcano always had a slight fumarolic activity. It was restricted to the crater area. In November and December 1984, the fumarolic activity increased and the first ash emission and vapor-sulfur formation started. Small local earthquakes accompanied these volcanic activities. The volcano had a small erup¬tion on Sept. 11, 1985. It was manifested by phreatic explosions that ejected fragments of the vent and formed ash deposits 25 mm (1 in.) thick around an area 2.5 km (1.5 miles) from the crater. Fine material was blown by the wind and reached Manizales and neighboring areas, producing a small layer of ash up to 10 mm (0.4 in.) thick.

Jan 2, 1986

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By E. A. Twichell

An entirely new concept in the effective utilization of magnetic, energy has resulted in a major break-through in the design of magnetic separation equipment. One of the first applications of this concept has resulted in the development of a Permanent Magnetic Wet Drum Separator with strength .and operating characteristics equal to Electro Wet Drum Separators. Prior to this development when strength and adjustability were required, electro wet drums were specified even with all their drawbacks. The electros, by nature, are subject to coil failure or burnout, over-heating and loss of strength, high power consumption and generally high maintenance. Now the high strength and the adjustability, formerly the exclusive property of electros, has been engineered into permanent wet drum separators. These units combine maximum field strength in the separation zone with strength adjustment to suit changing conditions. Adjustment can be effected while the drum is in operation without stopping either the feed or the drum.

Jan 1, 1967

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By J. S. Hayden

It is becoming increasingly difficult to secure local aggregate resources that meet quality standards and local restrictions without conflicts with other land uses and environmental regulations. The successful integration of natural-resource information into land-use decisions is becoming increasingly important as the needs for both land and resources become more numerous, complex and urgent. Well-reasoned decisions about land-use are crucial to the Nation if infrastructure resources are to remain economically available. Provisions for uninterrupted future supplies of aggregate should be made using proper long-range planning that incorporate a multiple land-use program. That program would include identification and protection of natural resources, strategies that will permit development of resources according to future market needs and environmental considerations, and the beneficial reclamation of mined-out areas.

Jan 1, 1997

By Tim O’Neil

Dressed in black tie and Victorian attire, some 200 people came to Leadville, CO, for a September weekend featuring a National Mining Hall of Fame and Museum (NMHF&M) induction banquet and a scenic mountain train trip to Fremont Pass and the Climax Mine. The 18th annual induction banquet on Sept. 17 began with cocktails and a open house. It was a chance for visitors to tour the National Mining Museum including the new Hennebach Wing, opened in February. The new wing is named in honor of Ralph Hennebach, retired chairman of Asarco. Formerly Leadville Junior High School, the Hennebach Wing encompasses more than1,440 m2 (15,500 sq ft) of floor space in two stories. One prominent feature is a 1923 Wills Sainte Claire touring sedan. Climax Molybdenum donated this first all-molybdenum steel motorcar. Docents were available throughout the museum to give banquet attendees directions and answer questions.

Jan 1, 2005

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By Lynn B. Hales

There is a large economic opportunity associated with improving metallurgical performance in mineral processing plants that use process control. Thus, future control systems will be developed towards more sophisticated user friendly, computer-based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, once considered cost centers, will be integrated into plant-wide control systems for economic control and optimization. This article looks at new control hardware, process sensors, control strategies and software development tools. It also looks at the economics driving the continued development of advanced process control systems. Process control systems routinely used in the mining industry were born when the microprocessor was invented. They have continued along an evolutionary path from vendor specific processing hardware and proprietary operating systems to computer industry standard "open architecture" systems. The many economic forces that drive the development and functionality of these process control systems will cause this evolutionary process to continue. Two of the broadest categories are the needs of the end users and the desire of the system manufacturers to distinguish their products from one another. More

Jan 1, 1994

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2004 was estimated to be 635 kt (700,000 st). This was a 2-percent increase from 2003. The value of processed diatomite in the U.S. was about $164 million in 2004. Production was from six companies with 13 processing facilities in four states. Nevada and California were the principal producing states. They accounted for about78 percent of the U.S. production during 2004. U.S. diatomite exports were about 136 kt (150,000 st). Imports were negligible.

Jan 1, 2005

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996