Search Documents

By T. Payne

Underground heat issues are mainly focused on the detrimental effects to a workers health. However, working in hot, humid conditions has other negative effects. Studies have shown that safety, productivity, workforce morale and operating cost are also worsened in these conditions. The human body has several mechanisms for rejecting heat and remaining cool. However, once the air temperature exceeds about 34°C, the only effective mechanism is by evaporation of sweat from the skin. This is assisted by acclimatisation which is the human body?s enhanced ability to combat extended exposure to heat. The body has to remain well hydrated when working in heat as even small degrees of dehydration cause significant decreases in the ability to work in heat. There are two ways in which heat load can be reduced: Through use of refrigeration/vent/cooling to reduce thermal stress on workers; Reduce the contribution that heat sources have to underground heat load (e.g. reduce idle time, fleet size, etc). Some of the sources of underground heat have the potential to be more manageable than others. Geothermal heat and heat from autocompression will be found in all mining situations in varying degrees depending on geothermal gradient and surface temperature, however, the use of equipment and blasting may be streamlined to reduce the underground heat load. It is through a combination of the available options that most mines will successfully control their heat related problems. Mt Isa, which has been a focus for heat related study in Australia, has successfully implemented protocols for working in heat. Through combining these with the installation of a surface bulk air cooling plant, Mt Isa has consistently reduced the incidence of heat illness. This is likely to be the most cost effective method of reducing heat load for deep mines in Australia. Shallower mines which may only occasionally encounter hot conditions should consider more portable cooling options. This study will review the heat issues in underground Australian metalliferous mines.

Jan 1, 2009

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By M. Götze, P. Eysel

Over the last years, the importance of the assessment of environmental and social aspects as well as of issues of good governance has increased significantly in mining finance. For this, international standards as well as internal guidelines of the banks and other involved institutions have been established and continuously improved. Considering these standards and regulations, the banks can influence the sustainability of mining projects - and they have done so in the past -, mainly by implementing certain provisions and covenants in the loan documentation, binding the financing to the mining company’s adherence to the agreed sustainability standards. However, there are limits to the banks’ influence due to the competitive environment with other available means of financing. Nevertheless, the experience of the last years has shown that the standards and regulations bound to the financing by the banks help to lead the mining industry towards more sustainable projects.

Jan 1, 2011

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000

By B. Samoski

In late 1994, EPA and OSM acknowledged that efforts by any one agency or by the many different agencies to remedy the water quality impacts of decades of contamination from abandoned coal mine lands in Appalachia would not be successful if their disjointed efforts were not unified and if the local watershed organizations were not included. The result of the collaboration between EPA and OSM was the creation of a statement of mutual intent which was a pledge by government agencies, watershed organizations, and the industry to restore watersheds degraded by acid mine drainage from abandoned coal. The presenter will describe the evolution of this pledge from a paper promise to on-the-ground remediation projects.

Jan 1, 2002

By Bryan Ulrich

Knight Piésold and Co. hosted its annual roundtable discussion on March 17, 2011 at the Stockman Hotel and Casino in Elko, NV. The theme for Roundtable 2011 was, ?High density tailings, paste, and filtered tailings,? although the topic may well have been subtitled, ?Don?t prematurely rule out any technologies before they are given their day in court.? Bryan Ulrich, Knight Piésold?s local representative, as well as Tom Kerr from Knight Piésold?s office in Denver, CO, were on hand to help facilitate the discussion. Ulrich and Kerr are senior vice president and president of Knight Piésold?s U.S. practice, respectively. The event played host to more than 30 attendees from several western states. Attendees included personnel from a dozen mining properties and various corporate offices. There were also attendees from manufacturing and specialist consulting firms who have been providing services to various high-density tailings, paste and filtered tailings operations worldwide. It may be noted that the term ?filtered tailings? is used in this discussion. Alternative terms, such as ?dry stack? or ?dewatered tailings,? should be avoided whenever possible, as such terms tend to give a false sense about the nature of the material since these materials typically still retain a significant amount of moisture.

Jan 1, 2011

By X. P. Zheng

Barium fluorphlogopites were synthesized in the laboratory in order to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between layer structure and the Ba-O bond length. The higher barium content, the larger the cell volume and distance between the layer structure and the longer the Ba-O bond, the more negatively charged the surface is and hence the more easily adsorbed to cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1993

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By K. C. Ko

The pit slope angle dictates the economics as much as the depth of the pit. Steeper slope provides more ore reserves, at the same time, the steeper slope presents higher probability of instability and associated maintenance problems. While large open pit mines mostly belonged to nonferrous metals in the past, other mines are becoming deeper as the mine economics permits deeper mine operations, Such minerals include coal, uranium, phosphate, and others. There are some basic differences between an open pit slope and slopes that are encountered in usual civil engineering work such as dam embankments and highway cuts (Figure 1). The stability of the civil engineering slope changes continuously with time due to ground-water movements, weathering, etc. But the stability of the open pit slope (Figure 2) changes more drastically day-to-day or even hour-to-hour, These changes occur because not only is the slope geometry being continuously changed by the mining operation, but also different geology and geologic structures are being exposed on the slope. Even when a particular slope area is not presently being mined, excavation in adjacent areas can affect the general condition of that slope area. A pit will experience some slope failures during its life.

Jan 1, 1977

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By R. A. Gee, G. B. Ashton, S. T. Warren, P. N. Groves

Northside Storage Tunnel provides 500 megalitres (Ml) (130 million gallons) of storage capacity to capture stormwater/sewage overflows into Sydney Harbour. The6.6 m diameter TBM driven tunnel traverses Middle Harbour 85 m (280 ft) below sea level and through a sandstone/shale rock mass, highly disturbed by stress relief, 20 m(65 ft) beneath the base of the sediment filled palaeochannel. Target limits for inflow, groundwater drawdown and settlement of the valley beaches were achieved by systematic forward grouting from the TBM. Support included rockbolts, sets and shotcrete to carry rock loads, control block instability and spalling and to provide durability and serviceability. This paper describes the tunnelling and grouting works and their effectiveness.

Jan 1, 2001

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By R. Hedin, M. Dunn

The Pennsylvania Department of Environmental Protection (US EPA 319 program) provided funding to aid a public-private effort in the installation of an environmentally-friendly system to treat abandoned mine drainage at Jennings Environmental Education Center (Pennsylvania Department of Conservation and Natural Resources). Through this cooperative effort among state and federal agencies, mining, excavation, and environmental companies, college and home school students, Girl Scouts, and volunteers, a successful multi-component passive system, readily accessible for upgrades and public education/research activities, was built. 90 people were directly involved in construction of this award-winning system and about 1000 people annually benefit from the educational opportunities.

Jan 1, 2002

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007