Search Documents

By Sigmund D. Schwarz

INTRODUCTION In late 1970, an experimental geophysical program was undertaken at the Lake Huron Tunnel for the purpose of developing a geophysical technique that could be applied to determining the thickness of rock above the crown of the tunnel and identifying anomalous geologic conditions ahead of the face as the tunnel was advanced. The Lake Huron Tunnel is an 18.5 foot diameter machine bored tunnel having a total length of approximately 6 miles. The easternmost 4.5 mile section of the tunnel extends offshore beneath Lake Huron. At the time this study was started, approximately 1.5 miles of bore remained to be completed at the east end of the project. The tunnel is part of a raw water intake for the City of Detroit water supply. The Lake Huron Tunnel is bored in Antrim shale, a dense marine shale of Mississippian or Devonian age. The west end of the project encountered banded brown shale containing numerous calcareous concretions ranging in size from a few inches to more than 16 feet in diameter. As the tunnel was advanced in an easterly direction, a transition was encountered into very uniform gray shale. One set of prominent vertical joints was encountered with a strike running approximately 15 to 20 degrees askew of the tunnel axis. Bedding is essentially flat. Variable quantities of salt water and natural gas occur in the rock. The results of exploratory drilling carried out for preliminary design studies indicated that as little as 30 to 35 feet of rock cover could be expected under the lake at the east end of the project.

Jan 1, 1997

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By D. Brandt

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority. The Engineering Department started a project to improve fragmentation through blasting and thus increase throughput in the crushing system. It soon became clear that input from other departments was going to be required to make this a safe and economical project. Therefore the Crush and Convey and Ore Control departments worked together to evaluate all available data on blast patterns and explosive loads and tracked performance and results. Using image analysis, Drill Energy Index and databases, we have been able to improve fragmentation size and verify the results while controlling costs.

Jan 1, 2011

By D. Yokom, T. Katsabanis, E. Tremblay

"The mining industry has always faced the problems of replacing retired mining professionals, retaining their knowledge, continuously developing the skills of local talent and employing under-represented groups. In expansionary scenarios the industry faces the additional challenge of increasing available talent. New talent has traditionally come from current mining programs; however, these programs have been declining in numbers, and those that remain face challenges such as fluctuating enrollments, and reduced budgets. Queen’s University and Northern College have partnered to develop an innovative new program that offers online mining education to engineering technologists seeking to upgrade their skills and obtain a Bachelor’s degree. The high quality, flexible curriculum, offered online, includes a wide range of learning activities that promote interaction (student-to-student, student-to-instructor, and student-to-content), and is enabled by modern learning technologies (an integrated learning platform, as well as a variety of types of purpose-built video, web conferencing, and simulation software). The program issues block transfer credit to college graduates, and consequently reduces the time to completion when compared to other Bachelor’s degrees in Mining. The curriculum has been carefully designed to enhance a balance of technical, managerial, and societal skills for students. The program also includes short summer field school sessions, where students gain practical application skills under the direct supervision of engineering experts. THE NEEDS OF INDUSTRY Canada is the world’s largest exporter of minerals, and the contribution of this sector to Canada’s gross national product is more than three times that of the automotive industry, representing approximately 4% of Canadian GDP (MiHR, 2015)1. According to a recent report by the Canadian Mining Industry Resources Council (MiHR, 2016)2, despite the recent downturn in commodity prices, the industry will continuously need to attract new engineers to replace talent retirements and prepare for the possibility of expansion when the industry recovers. As past experience indicates, the challenges during expansion times are severe and the effects on education counter-productive. For example, during the prolonged expansion cycle of 2006-2012, several new programs were started worldwide, and mining became the profession of choice for many young students. During the subsequent downturn in the industry, many of these programs face dwindling enrollments, placing their sustainability in question. However, there is a continual need by industry to retain employees, as well as attract and train local talent, while providing educational opportunities to its employees. High potential college graduates can find themselves reaching a ceiling in their advancement due to their lack of a University degree. Furthermore, there exists an under representation of women, immigrants, and Aboriginal peoples in the labour force, and engineering fields in general1,2. Traditional mining engineering programs have tried to respond to the needs of industry, as well as meet the needs of students seeking diverse and successful employment careers. These programs tend to cater to the educational needs and aspirations of a general population, and their ability to grow and respond to changing industry needs is constrained by the number of students they can attract, as well as the resources available to them in a steady-state scenario."

Jan 1, 2017

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By Mehdi Noori, Atefeh Azizitorghabeh, Fereshteh Rashchi, Ataollah Babakhani, Sarah Mahmoudi

The focus of this research was to evaluate the synergistic effect of bis(2,4,4-trimethylpentyl) phosphinic acid (CYANEX 272) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), diluted in kerosene, on the extraction and separation of Co(II) and Li(I) from synthetic sulfate solution. The results indicated that using a mixture of CYANEX 272 and D2EHPA was efficient in extracting and separating Co(II) from Li(I). The optimum ratio of CYANEX 272/D2EHPA was found to be 5:1, in which the highest separation factor was obtained (5973.23), and ΔpH0.5 was 4.10. Adding tributyl phosphate (TBP) as a modifier and increasing the temperature improved the metals’ separation rate and extraction efficiency. Thermodynamic studies were also carried out, and ΔH, ΔS, and ΔG values were computed, revealing the endothermic nature of Co(II) and Li(I) extraction by CYANEX 272/D2EHPA mixture. The conducted experiments for the McCabe–Thiele diagram showed the possibility of using two stages to extract over 99% of Co(II) and Li(I). Slope analysis and Fourier transform infrared spectroscopy (FT-IR) were employed to comprehend the Co(II) and Li(I) extraction mechanism using a mixture of CYANEX 272 and D2EHPA.

Jan 17, 2022

By D. M. Abbott

The problem with best practices occurs when they do not work. This happens when the seldom-stated assumptions underlying the practice are not met. This paper provides some examples for the mining industry: (1) when core splitting is inappropriate, (2) when the use of fire assays for placer samples is inappropriate, and (3) when high-grading may be acceptable. Geologic conclusions are, in the final analysis, expressions of judgment predicated upon knowledge and experience. A geologic conclusion, however, purports to be more than an arbitrary determination—it is reached as a consequence of method. No specific method is required, but the method used must be an orthodox method, in accordance with orthodox definition of terms, and the one best adapted to the dealing with the questions asked about the property in question. Whether the so-called “best practice” is really applicable to the job at hand must be decided on the basis of professional scientific judgment. When one decides to deviate from a published “best practice” for sound scientific reasons, describe in detail in the report what the so-called “best practice” is, why it was inappropriate for the project, and why the method used was better. If one becomes aware that a “best practice” is being proposed, actively urge those proposing it to include in its description the underlying assumptions that must be met in order for the “best practice” to be valid.

Jan 1, 2014

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

By Jacob Bouke, Jason Janisch, Erik Vlot

The use of conventional tailings deposition methods has been the standard for decades. With the need to reduce the impact of mining, alternative methods are considered when expanding or upgrading tailings handling systems. Converting an existing tailings management system to a more sustainable deposition method during the operation of a mine may incur considerable operational and financial risk, and when assessed more traditionally, does not provide significant advantages. As a result, most mines choose to continue their current technology and add an additional pumping stage or pumpstation to their tailings line in case of a pipeline extension or Tailings Storage Facility (TSF) expansion. This also often involves raising embankments. Changing pumping technology is traditionally assessed by comparing the energy efficiency of current and prospective pumping technology. Despite a reduction in absorbed power, this traditional assessment does not include possible savings in water and the carbon footprint. With the consideration of all these three aspects, alternative pump technologies, such as Positive Displacement (PD) technology, become more economically feasible, providing increased sustainability and enable a site to future-proof their operations. Project feasibility may be affected by the high capital investment required for PD pumps. The benefit of applying PD pumping technology could be enhanced by reducing the volumetric throughput of the pipeline by dewatering the tailings to 65% solids concentration by weight. It was found that despite increasing capital expenditure, the improved reclamation of water will have a positive effect on the direct and indirect cost of fresh water intake to mine operations. This paper seeks to illustrate that in many applications the long-term benefits of investing in sustainable tailings management are optimized when more efficient PD pumping technology is combined with tailings dewatering when upgrading or expanding the tailings handling system.

Feb 1, 2024

By P. Christmann

"In June or July 2005, the European Commission will present its Thematic Strategy on the Sustainable Use of Natural Resources proposal to the Council and European Parliament, one of the seven Thematic Strategies to be developed and implemented under the 6th European Environment Action Programme in support of the European Union’s Sustainable Development Strategy defined by the European Union’s Head of State at the Göteborg European Council, in June 2001. The time scale for this Thematic Strategy is 25 years (2005-2030). This paper discusses some of the key issues related to the EU minerals and metals industry that needs to be addressed by the Strategy. These are: - the need for access to mineral reserves in the EU and abroad; - the need to strenghten the capacity of developing countries to sustainably promote and regulate the use of their mineral potential; - the need for an EU mineral resources intelligence capacity. There are additional important needs, which are not discussed in this paper, such as: - the need to foster further innovation in mining, ore beneficiation and metallurgical technologies; - the need to integrate and simplify the exisitng complex regulatory framework applicable to the EU mining industry and to effectively implement existing legislation."

Jan 1, 2005

By Barbara B. Newlin, Emily Rosenberg, Marianne Snedeker

Whose longwalls perform best in Eastern underground mines? What is the latest legislation affecting slurry pipelines? What are the trace element constraints on magma genesis? How can process set points be controlled more economically without affecting product quality? Where can I get a paper presented at the Australian Coal Preparation Conference? If answers to questions like these can help with your management decisions, exploration plans, or market positioning, your firm should know about Information on Demand. Information on Demand, Inc. (IOD) is a research service available to SME members to help them get the facts needed to develop business plans. IOD can function as a research staff and data bank specialist for geologists, planning specialists, production managers, and engineers in all levels of the mining industry. Just dial 415-549-3259 and ask IOD for a copy of an obscure article, a comprehensive literature search, or a background report on a company, a process, or a product. Within a short time, IOD will have the information you need delivered to your office or worksite. Information on Demand has a bank of dial-up terminals that provide access to more than 200 business and technical data bases, including Lockheed's Dialog, CompuServe, InfoLine, The New York Times Information Bank, and other systems. These data banks contain more than 95% of the world's technical literature published in the last 10 years. There is no input required from individuals or companies. The data bases are maintained by publishers and are constantly updated with abstracts of articles, reports and reviews, and other text appearing in more than 5,000 engineering publications, as well as thousands of other trade and technical publications. The data bases are organized by subject and offer a speedy comprehensive survey of world literature. One data base, called Compendex, provides worldwide coverage of engineering publications, meetings, and reports. The Metadex data base abstracts literature on the science and practice of metallurgy, and can be accessed by commercial, compositional, and numerical alloy designations. PatSearch and Claims data bases enable IOD to determine what patents have been filed by a given entity, what international patents are equivalent to a US patent, and other vital patent information. In the non-technical arena, the Commerce Business Daily has daily updates of federal procurement information. The Federal Register is abstracted on-line in a data base, and ABI/Inform is a data base full of marketing and management information for all industries. IOD offers a free pamphlet listing these and other data bases. A typical literature search from IOD will produce 60-200 references with abstracts, and can be printed out off-line and mailed or transmitted directly to an electronic mailbox. Abstracts will often give all the information needed by the reader. At times, when the complete article or technical report is needed for further study, IOD will send a photocopy of the full text for a small additional fee. Patents, books, securities exchange filings, standards, and specifications can also be supplied by means of IOD's network in major libraries, such as Harvard, MIT, and The Library of Congress. A technical translation service is available for foreign

Jan 12, 1983

By Chee Theng

"What do you think are the most important topics in mineral processing today? It is a question that begs to be asked when more than 100 of some of the best and brightest in Colorado mineral processing and their invited guests are gathered in one room. They are there for the 66th Annual Colorado MPD Meeting held at The Broadmoor in Colorado Springs: three days of finely curated talks and social events where participation was strong, and information was exchanged and connections forged in a relaxed, informal atmosphere.Water, tailings and social licenseNot surprisingly, water management, with the associated issues of tailings and social license, was high on the minds of those present. The Mount Polley and Samarco tailings dam failures have had repercussions across the industry. “There are big challenges with respect to tailings, and social and environmental pressures to find better ways to treat them,” said Steve Hearn of Huntsman Corp., a view echoed by Bob Kilborn of Kilborn Group LLC. Metso Minerals director Keith Butler said, “Water conservation is a key issue today. Many mining activities are now located in remote areas, so it has social and economic impacts on mining operations.” For Brian Olson of Samuel Engineering, wastewater and reclaimed-water treatment is interesting.Fittingly, the first talk of the meeting was on dry stack tailings by Michael Blois of Takraf USA, who went over both the advantages and disadvantages. “The average now is over one tailings dam failure a year,” Blois said, “and that is one too many.” But the technology may not be the right fit for all projects. In his talk on the KSM project, Jay Layman, president and COO of Seabridge Gold, showed how it isn’t practical for KSM and how Seabridge reached the decision on a cyclone sand tailings managementfacility as the preferred management strategy.The luncheon keynote also dealt with a tailings pond spill, but of a different kind. Bob Schafer, chief executive of Eagle Mines Management, spoke on the federal missteps that led to the spill into the Animas River from the Gold King Mine, a mine that had been a dry mine throughout its life and up to the 1990s."

Jun 1, 2016

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By Galymzhan Karamyrzayev, Rashid Nadirov

Zinc ferrite ( ZnFe2O4) is a by-product of non-ferrous metal production and is considered a promising source of raw zinc. The most efficient way to extract zinc from its ferrite is via acidic extraction, specifically leaching by hydrochloric acid. A comparative study of synthetic zinc ferrite hydrochloric acid leaching in isopropanol, aqueous, and the mixed solvent was performed. Zinc ferrite was obtained by sintering a zinc and iron (III) oxide mixture. Crushed samples were subjected to leaching in 1 M HCl at 323, 333, and 353 K and pulp density of 1 g/100 mL. The dissolution of zinc and iron into solution in organic media reached 77% at 353 K, while in an aqueous environment this value was 65%. The activation energy of 70.0 kJ/ mol was found for the leaching process in an isopropanol environment, which is lower than that in an aqueous solution by 15%. The more efficient leaching effect of isopropanol is attributed to the lower dielectric constant of the alcohol which increases the affinity of chloride anions for zinc and iron cations at leaching.

Jun 5, 2022

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979