Search Documents

By Richard R. Klimpel

Introduction Froth flotation is one of the most common unit engineering operations in use today. Its aim is to upgrade the quality of coal by removing ash/pyrite and separating selected minerals from undesired gangue materials. Flotation has been successfully practiced at the industrial scale for more than 50 years. Its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation has also shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a given equipment configuration. The operation must exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the mechanical flotation cell is scaleable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required - pH regulators, frothers, collectors, activators, and depressants - are all relatively inexpensive and common. They are not usually used in large quantities. Froth flotation is certainly one of the most versatile and forgiving unit operations in the chemical, mining, and agricultural industries. The problem with the industrial flotation process is that it is fairly easy to get reasonable results and relatively difficult to get excellent results. Why is it so difficult to fine tune the froth flotation process? There are some obvious reasons and a few not-so-obvious factors. The obvious category would certainly contain the tendency of natural feed materials (ores and raw coals) to have variable physical, metallurgical, and surface properties. This occurs even when special care is taken to minimize such differences with blending. There is another obvious reason for difficulty. An inherent broadness of the feed particle size range to flotation results from using any of the common industrial-scalefine grinding devices - ball-, rod-, or autogenous mills. Research has been done into the chemical reagent and equipment aspects of flotation. It has shown strong interactions (limitations) of chemical reagents and equipment on larger and smaller particles. The point is that current flotation practice works best on average- or medium-sized feed particles. The greater the amount of large or small particles, or of both large and small, the more difficult it is to achieve excellent flotation results. Other reasonably obvious factors include: • variations in mineral type and liberation sizes; • water chemistry variations such as those involving Ca", C03, or Fe", or various soluble metal cations; • the presence of stray organic materials such as returning soluble reagents or partially degraded reagents in reuse water; • the lack of reliable on-line instrumentation for monitoring and control; • frequent equipment malfunctions of all types; • excessive feed rates for installed plant capacity; • poor operator interaction with the process; and • poor reagent dosage control. There are less obvious, but real limitations to flotation. These are inherent in the design and operating characteristics of the most common cell design in use today - the mechanical flotation cell. Individual performance attributes of the chemical reagents used, along with their manner of use, also carry limitations. The bulk of this paper will deal with chemical reagents and their use. Chemical reagents In 1979, the author and his co-workers were asked to invent and implement, at the industrial scale, new flotation reagent chemistry. After reviewing some of the literature (Sutherland and Wark, 1955; Klassen and Mokrousov, 1959; M. Fuerstenau, 1962; D. Fuerstenau, 1976; and Leja, 1982), a series of carefully controlled plant scale tests were set up. These tests were designed to understand existing reagent scale-up from the laboratory to the plant. They were to quantify at the plant level the effect of some of the more important, controllable chemical reagent factors (frother and collector type, frother and collector dosage, pH effects). This is a learning experience that all researchers involved in flotation theory should experience. It quickly became apparent that: • because a factor is important

Jan 12, 1988

By A. Noble

The design of separation circuits can be a complex, labor-intensive and costly process. While the engineer?s experience along with extensive data sets and simulation are crucial tools for determining the final solution, a more fundamental approach is suitable to compare preliminary options and reduce the number of potential alternatives. In light of this need, the authors have developed the Circuit Analysis Reduction Tool (CART?). This software package relies on the fundamental principles of linear circuit analysis; however, the solution methodology has been streamlined to automatically incorporate stream splitting and unique separation performance for each unit. The resulting tool allows preliminary analysis of circuit designs without the need of detailed feed characterization. In addition to the basic analytical approach, this paper supports the veracity of the methodology with several simulated examples for various separation models.

Feb 27, 2013

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990

By SH. Shahsavari, H. Akbari, M. Noaparast, M. Oliazadeh

Mejel valley zircon ore in Iran is located in north part of Iran and was sampled to evaluate its concentration. The aim of this project was to define the mineralogy of this zone and separating zircon from other minerals using gravity concentrators and magnetic separators. It is constituted of various valuable minerals, mainly zirconium, niobium-tantalum, titanium, rare earth elements particularly cerium-bearing minerals namely zircon, sphene and rare earth elements oxides. We used statistical method for designing of experiments. Yates method used for analysis of basic experiments results. The grade of zircon in primary sample was 1.1%. Different experiments were designed to optimize all required parameters. The final concentration with 75% zircon was produced and final recovery was 79%. Finally, lab-scale based flow sheet was prepared using experiments results.

Jan 1, 2005

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By S. Agarwal, S. Frimpong

The creation and maintenance of a healthy working environment in surface mining operations require sustained efforts in pursuing advanced research initiatives toward the development and deployment of powered haulage technologies. This paper contains progress summary on a frontier research in truck dynamic control, vision and collision avoidance. This research is required to provide solutions to challenging problems regarding operator visibility in truck haulage in a surface mining environment. The paper focuses on truck control kinematics and dynamics, truck-haul road interactions, intelligent truck sensing, intelligent truck collision avoidance system, integrated system for situational awareness, augmented visualization and operator interface, and field testing and error variance modeling of developed technologies. A sensor suite of four subsystems, including front-side stereo-camera, front-side Doppler radar, close range sonar proximity sensors, and rear-side camera system have been recommended for developing a 360° truck operator vision to allow safe operations. This research initiative is significant because it will provide a strong basis for developing technologies to improve truck haulage safety in surface mines and construction sites.

Jan 1, 2007

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967

By William R. Yernberg

The combined 80th Annual Minnesota Section of SME Meeting and 68th Annual University of Minnesota Mining Symposium was held April 17 and 18, 2007, in Duluth, MN. About 350 mining industry professionals attended the conference, including engineers, executives, mining managers and suppliers from the United States, Canada, Australia, Finland and Brazil. This year’s theme was “Consolidation – Growth – Technology.” The 80th Annual Minnesota Section of SME meeting included concurrent technical papers sessions, a keynote session that featured two distinguished speakers and a general managers session in which taconite mine operators provided updates on their operations. The Minnesota Section meeting also offered an SME short course titled “Control the Feed, Control the Mill.” More than 50 individuals at-tended the short course.

Jan 1, 2007

By Greg Wieland

Deep sewer tunnels are required to meet future growth demands of the City of Austin?s down-town redevelopment. The tunnel is 18,000 ft long and varies in finished diameter from 54 inches to 96 inches. The tunnel crosses under Austin?s Town Lake three times and there are four main work shaft sites. Geology, groundwater, foundations, downtown redevelopment, and an active, healthy community put significant constraints on the design. This paper discusses a major underground project for downtown Austin and discusses the risk considerations and the opportunities the design team took toward optimizing the project design for the construction phase.

Jan 1, 2008

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By Harry Parker

Resource and Reserve Audits Becoming Increasingly Common Types of Audits -Review of Methodology (‘Fatal Flaw’) -Due Diligence – (‘Sign Off’) -Endorsement – (‘QA-QC’) Suggested Standards in Red

Jan 1, 2003

By P. Ashayer, J. Curran

Introduction Rockfalls occur when rocks or boulders detach from mountains or hills and tumble down. They can pose significant hazards to infrastructure such as highways, buildings, and mine open pits, and they sometimes result in personal injury or death. Prediction of rockfalls is a difficult task. Slopes that are at risk of rockfall have highly variable geometries. The location, mass, and shape of the rocks that might dislodge and fall are uncertain. Moreover, the materials that make up a slope can vary considerably from one section to another. Furthermore, the relevant material properties are usually not well known. Performing probabilistic simulations of rockfalls, combined with proper statistical analyses, has proven to be an effective and acceptable method for dealing with these difficulties [1, 2, 3]. The movements of a falling rock can be classified as freefall, bouncing, sliding, toppling, or rolling. The falling trajectory is controlled mainly by the geometry of the slope, the block shape, and the energy dissipated at each contact of the block with the slope. A rockfall model is evaluated based on its ability to efficiently predict the velocity, frequency, height of bounce, and run-out distance of falling rocks. With this information, the engineer can design remedial measures such as restraining nets and ditches. Most of the existing rockfall simulators are based on particle models that consider the falling rock as an infinitesimal particle with a mass, called the lumped mass or stereomechanical models [1, 2, 3, 4]. Other models involve hybrid methods relying on simplified assumptions. The most common hybrid methods are based on contact searching for the movement of a dimensionless object and incorporate some aspects of rigid body impact for bouncing [5, 6, 7]. There are also some rigid body models in the literature that employ simplified versions of rigid body models [8, 9]. This study applies a more sophisticated rigid body theory based on rigid body impact mechanics (RBIM), which was developed by Stronge [10, 11, 12]. The new theory captures all modes of rigid body movement. Due to the importance of the rock geometry, single impacts of ellipsoidal and prismatic rocks with rectangular cross sections are investigated. The effect of rock slenderness on rebound velocities and energies is also investigated for ellipsoidal rocks. The correspondence between the model parameters and the data from the rockfall literature data will be discussed.

Jan 1, 2007

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By Joseph G. Carleton

INTRODUCTION The increasing concern for the environment may well present far more opportunities than problems for those involved in all phases of tunneling. All too frequently in the past, environmentalists and their concerns have been cast in a negative light, as obstacles to be overcome. Often forgotten is the fact that these same environmental concerns have created a rapidly increasing demand for new tunnels. Tunnels for rapid transit projects, clean water supply, and sewage treatment have been given a boost because of environmentalists' concerns about overuse of automobiles, inadequate water supplies, and improper sewage disposal. Concurrent with increasing use of tunnels to help solve or alleviate some of our environmental problems is an obligation not to create new ones in the process. Concerns which we feel responsible tunnel owners, engineers, and contractors should address themselves to include: (1) Minimum energy consumption, both during construction and in operation of the completed project; (2) proper storage and/or disposal of the excavated material; (3) minimum disruption during the construction process - noise, traffic, unnecessarily unsightly work areas, and possible weakening of foundations of nearby structures; and (4) a finished project consistent with community and environmental goals. We are especially concerned about two things. First, the longrun implications of a project -- what's good for a few people in the short-run may be bad for most of the people in the long-run. Cutting corners to save a little money now is false economy. Second, the fact that ultimately we all share the same earth -- its water, air,

Jan 1, 1974

By Donald J. Hill

To be successful, every organization within the mining industry must involve itself in researching and evaluating methods of loss control. The appraisal and evaluation of accidents and injuries is required to determine the costs of loss producing practices and conditions. This involves all of an organizations disciplines that concern themselves with a more efficient and cost effective organization. To come to know the cost of your safety program or how much is expended yearly for each employee on safety; to know what your safety costs are per man-hour or per ton-produced; to know what the health, medical and compensation costs are for any given incident are just a few of the important facts and figures that the safety management of a given organization needs to know to operate in the mining industry today.

Jan 1, 1984

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By George E. Aiken, B. R. Jr. Waples

INTRODUCTION In this paper the author will attempt to bridge from the paper work of design and engineering to the reality of implementation. Certain facets of construction are constant to a successful project, no matter the level of technical complexity. Basic to timely, low cost construction are the people assigned to the project. Construction is not accomplished by robots, computers, or speeches; but rather by people. People do however require the avail- ability of equipment and communications to properly complete the work. ORGANIZATION Good organization is the basic requirement of a well implemented construction project. For this paper the author will suggest an organization chart as well as an activity listing that together support the construction activities. There is little difference in the activities or functions needed to construct a small plant or a large one. It is a matter of how much time an individual has to spend on an activity that determines the structure of an organization. The difference between a large and small plant construction job is often described as the multiple hat versus the single hat philosophy. As an example, a resident construction manager on a small job might be the manager, the field engineer, the scheduler, the estimator, and the procurement manager. At some time during a construction

Jan 1, 1986