Search Documents

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By G. Ofori-Sarpong, A. -S. Adam, R. K. Amankwah

"In the application of the BIOX® technology, high tailings grade (2-16 g/t) may be generated with a decrease in overall gold recovery, which sometimes make it economically unattractive. This paper investigated the causes of the high tailings grade by using samples from the Bogoso BIOX plant. Partial chemical analysis, diagnostic tests and cyanidation optimisation studies were conducted to invoke understanding into the high tailings grades. Diagnostic study on the tailings showed 48.34% of gold in carbonaceous matter, 17.12% in quartz, 13.40% as liberated gold, 11.51% imbedded in sulphides and the remaining 9.65% in carbonates. Optimum cyanidation recovery of 90.4% was established for the BIOX concentrate at 7 kg/t NaCN, 40-50 g/L activated carbon and residence time of 40 hours. The recovery was sensitive to carbon and cyanide concentrations but additional cyanide was not economical. High preg-robbing indices of 72.7% and 64.4% were recorded for the BIOX product and the flotation concentrate respectively. This confirms the inability of the BIOX process to deactivate carbonaceous matter, which remains a serious precursor for low overall gold recoveries and high CIL tailings. INTRODUCTION Gold ores may be broadly classified as refractory and non-refractory. Non-refractory ores are easy to treat but refractory materials require complicated flowsheets for metal extraction (Hausen and Bucknam, 1985; Schmitz et al, 2001; Marsden and House, 2006). As near surface non-refractory gold deposits are getting depleted, the increasing price of gold and increasing demand for gold, have encouraged many gold producing companies to treat refractory ores for gold recovery. The refractory behaviour of these ores may be due to the presence of sulphides, tellurides, cyanicides and/or carbonaceous matter. Refractory ores do not respond well to conventional cyanidation as the gold is either occluded by or in solid solution in sulphides, or is in association with cyanicides (Marsden and House, 2006). Further, carbonaceous matter preg-robs gold during leaching (Osseo-Asare et al, 1984; Hausen and Bucknam, 1985; Schmitz et al, 2001). The two major causes of refractoriness are the presence of sulphides and carbonaceous matter, and these render the ore double refractory (Nyavor and Egiebor, 1992). Oxidative pre-treatment processes such as high pressure leaching/oxidation; biological oxidation, ultra-fine grinding and roasting are required to render refractory ores amenable to conventional cyanidation (Marsden and House, 2006). Biological oxidation, however, has become the preferred pre-treatment route because it is more environmentally friendly and convenient even where only partial oxidation is required. Comparative tests have demonstrated that bioleaching can achieve the same or better results than roasting or pressure leaching in terms of gold recovery (Yannopoulos, 1991; Brierley, 1997). Further, biological treatment processes are more cost-effective, environmentally friendly and safer."

Jan 1, 2017

By Karin Bäppler

"When considering large-scale infrastructure projects worldwide special attention has to be paid to the large diameter tunnel construction projects that were successfully completed in the Southern Hemisphere. The projects that are highlighted in this paper are large-scale infrastructure projects in the sector of transport. In focus are four road tunnel projects that were constructed in Australia and New Zealand using mechanized tunnelling technology. The tunnel boring machines (TBMs) that were reliably applied to these four major projects all exceed the bore diameter of 12 meters. These TBMs are therefore in the range of large to very large diameter TBMs. The technology used demonstrates state of the art technology with tailored tunnelling technology adapted to the specific project demands. Two Double Shielded Hard Rock TBMs (Ø 12.35 meters) were used for the construction of the Clem Jones Tunnel in Brisbane crossing beneath the Brisbane River and these two machines have been reused for the excavation of a 4.3km long two-lane highway tunnel for Legacy Way in Brisbane creating a new traffic artery towards the city centre. Two EPB Shields (Ø 12.48 meters) excavated and lined the twin-tube road tunnel for the Brisbane Airport Link. Excavation diameters in excess of 14 meters, such as the Earth Pressure Balance Shield (Ø 14.41 meters) involved in the Waterview Connection Project in New Zealand, are understood in the tunnelling industry as very large diameters. The machine is customized to the requirements and subsurface conditions of Auckland. The paper spotlights the large to very large diameter TBMs that were used and focuses on the comprehensive solutions developed by the machine manufacturer to provide a system with benefits for the contractor especially for the Waterview Project. INTRODUCTION Extensive large-scale road infrastructure projects like the ones implemented in Brisbane (Australia) and currently under construction in Auckland (New Zealand) show the tendency of today’s infrastructure construction projects. Functional infrastructures need to be put in place to cope with the demand of mobility and flexibility of people living in cities and metropolises. Impact during construction work to people or environment has to be kept as low as possible to ensure the quality of life is not disrupted."

Jan 1, 2016

By R. Stanevich

Studies by the National Institute for Occupational Safety and Health (NIOSH) and the Bureau of Mines (BOM) have demonstrated that: (1) 90% of diesel particulate is less than one (1) micrometer in aerodynamic diameter; (2) more than 90% of the respirable mass in electric coal mines was greater than one (1) micrometer in aerodynamic diameter; and (3) in coal mines using diesel equipment, average diesel concentrations can represent up to 53% of the MRE respirable coal dust standard. For mines approaching the 2 mg/m3 standard, compliance may be easier to attain by controls directed at diesel exhaust particulate as opposed to coal dust control. First, however, a Simple instrument is needed to measure diesel exhaust particulate concentrations. This paper describes such a sampler, its construction, and use. While results from this sampler are primarily utilized to identify control areas, NIOSH is also using the sampler for estimating worker exposures in epidemiologic studies.

Jan 1, 1988

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By S. Bahrampour

One of the basic requirements for designing an optimized rock support for an underground opening is having reasonably enough geological information. It is often financially impractical to obtain detailed geological information about the rock surrounding the excavations. The geological and geotechnical information which are obtained during the construction phase are also usually inadequate and need periodic operation stoppage. Penn State University- J.H. Fletcher & Co. joint venture is to improve the existing instrumented roofbolter so that the 3D geological and geotechnical map of the rock mass surrounding the underground working can be generated real-time as the data is being collected. This information will also be used to design appropriate support for different sections of mines. In this paper, recent results in improving the performance of the measurement while drilling system will be discussed. Moreover, updates related to borehole probing methods for estimating the properties of the rock masses will be presented.

Feb 23, 2014

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

By V. P. Keran

Design of the Bajo de la Alumbrera Project started in June 1995 and concentrate production commenced early in the Third Quarter of 1997. The project is situated in North-Western Argentina and is being developed by Minera Alumbrera Limited which is owned by MIM Holdings Limited of Australia (50%), North Limited of Australia (25%) and Rio Algom Limited of Canada (25%). This paper outlines the key features that were incorporated in the design from both process and plant layout perspectives. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity gold circuits in both primary and regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry's remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy's efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966

The United States is being invaded... by foreign capital: marks, francs, pounds, yen, lire, riyals, you name it: On almost any given day the Wall Street Journal will contain a new report on a department store, newspaper, bank, hotel, agricultural land, supermarket chain, et a1 being bought into by overseas investment. Xenophobic reaction to this revised national condition has begun to set in. Several farming states have and are introducing legislation to monitor foreign land buying. In Congress a mandatory reporting requirement for foreign purchasing is currently under study. In a relatively short period the country has reverted from world leader- ship in overseas acquisition and involvement to become itself one of the prime investment opportunities in existence. Interestingly enough, one of the industries where this changed status has become most apparent and pronounced is within that small/regional/segmented/low value-to-weight bulk commodity enterprise ranked as the backbone of the nation's construction activity. U.S. cement making is not only undergoing internationalization in its ownership, but also in its product, equipment, and engineering expertise.

Jan 1, 1979

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017

In its largest product launch in company history, Cummins Engines welcomed more than 200 customers, vendors and media to witness the unveiling of its new QSK95 engine at its Seymour Engine Plant in Seymour, IN on Nov. 1. It took the efforts of 150 engineers to design the QSK95 and more than $100 million in investments to establish a new production line and test facility at Cummins? Seymour Engine plant. The result of these efforts is a new platform of engines that Cummins says will provide as much as 2,983 kW (4,000 hp) and will be the most powerful, high-speed diesel engine ever built.

Jan 1, 2012

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity which exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into worldwide business with a capacity of about one-half million tons/yr. This paper will present data on the chemistry, mining, manufacturing and applications for acid- activated clays.

Jan 1, 1986