Search Documents

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By Neal P. Cochran

My talk today is an effort to project our thinking forward a few years to that point in the future when we will be producing gas and liquid fuels from coal. To those of you that are concerned with meeting today's production quota--my remarks may sound like a Buck Rogers projection. Not so. Although I'm talking about the future, please understand that my thoughts are focused on the near term future. The coal plant of the future will be an energy plant producing energy products to meet the needs of our modern society. This plant is an outgrowth of Government- industry cooperation. Much of the research work that makes such a plant possible was jointly funded, other work was a continuation into development of private research expenditures, other work was performed by private research organizations with Government funding, other work was performed in Government laboratories, both State and Federal. As indicated above, and in the title of my talk, I expect to describe the coal plant of the future. I will describe a plant producing Carbon, Oil, Pipeline gas, and Electricity--Project COPE. This plant copes with the Atomic-Nuclear Group. As stated above, this plant is an energy plant. Energy plants today are large-scale operations. Power plants of 5,000 megawatts are projected, refineries of 500,000 daily barrels are near term probabilities, 48" transcontinental gas pipelines are with us today and 25,000 daily ton mines are here as well. The COPE plant will be of the same general size and require 50,000 - 100,000 tons of coal per day.

Jan 1, 1969

By Walid M. Abdellah, Soliman Abu Elatta A. Mahmoud, Hanaa A. Abu Khoziem

The high-grade Th-U-Y zone is one of the numerous mineralized zones found in the El Garra El Hamra hydrothermally altered syenites in southwestern Egypt. It is characterized by the thorium minerals thorite and thorogummite, which are closely associated with xenotime-(Y). This zone of mineralization is localized in the eastern part of the El Garra El Hamra hydrothermally altered syenites. This zone does not relate to the first phase of syenites that appeared on the surface but is linked to the other, hidden phase of the syenitic body. Additionally, the fluids responsible for the mineralization of this zone belong to the late-stage hydrothermal event as well as the fault action due to the fact that it had continued reactivations for a long period of time. The studied mineralized zone also contains ceriopyrochlore-(Ce),(Ce,Ca,)2 (Nb,Ta)2O6 (OH), fluorite (CaF2) and barite (BaSO4), which are found in considerable amounts, whereas apatite (Ca5(PO4)3F) and chromite (FeCr2O4) are rarely found together with Fe-oxi-hydroxides (hematite and goethite) with a minor amount of jarosite (KFe33+(OH)6(SO4)2). Finally, the main constituent mineral in the zone is the pseudomorph perthite in addition to quartz, which is found as deformed crystals. A technological sample was collected from this zone and was found to assay 4.62 weight percent thorium (Th), 0.37 weight percent uranium (U) and 3.12 weight percent rare earth elements (REEs). From the chemical and mineralogical composition of the studied technological sample, the leachabilities of Th, U and REEs were investigated using sulfuric acid (H2SO4) agitation leaching and pug leaching methods. The latter was found to be preferred under the conditions of 0.54 ton H2SO4 per ton of altered syenite at 110 °C for two hours.

By Terry I. Mudder

Metal complexed cyanides in wastewaters form as a result of interactions of free cyanide with metals present in the wastewater and exhibit varying degrees of stability, toxicity, and treatability. Thiocyanate, a pollutant commonly found in cyanide bearing wastewaters, is formed through the interaction of free cyanide with sulfur containing species (i. e. pyrrhotite) both present in the wastewater. In certain industrial processes, such as the beneficiation of gold and silver, cyanide is an essential reagent. Since free cyanide, complexed cyanides, and thiocyanate are potentially toxic to humans and aquatic organisms, these compounds must be removed from wastewaters prior to their discharge into surface or ground waters serving as potential potable water sources, marine or fresh water habitats

Jan 1, 1984

By G. E. McClelland

Agglomeration techniques have been successfully applied to commerical heap leach cyanidation operations for the recovery of precious metals from low-grade ores, mine wastes, and tailings. The major parameters important for successful agglomeration pretreatment of these feed materials are discussed. Several commercial agglomeration-heap leaching operations are described. Two of the operations converted from conventional heap leaching to agglomeration-heap leaching after coventional heap leaching proved unsuccessful. Heap performance before and after agglomeration is discussed. A fairly recent operation that began production using agglomeration-heap leaching technology is also described. Two operations that processed milled tailings by agglomeration are discussed. The tailings feeds could not have been economically processed by means other than agglomeration-heap leaching.

Jan 1, 1986

By J. Z. Cheng

The extraction of thorium from industrial radioactive wastewaters discharged from Rare Earth (RE) plants was studied by the liquid membrane emulsion technique using P507- Span80-sulphonating kerosene-HCl. The emulsion conditions, the technological factors such as ratios of oil to the internal aqueous phase and water to emulsion, and the extraction time etc. were investigated.

Jan 1, 2008

By S. Hamilton

Occurrences of boron-containing ores are relatively rare on a global basis. The first verifiable use of borax was in the 8th century by Arabian gold and silversmiths. Due to the rarity of the borate mineral occurrences, borates were originally traded at relatively high prices and were used for very specialized applications. Today, there are

Jan 1, 2006

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party's mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By K. Terhaar

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.'s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

By Yashar Pourrahimian, Roberto Noriega

Truck fleet dispatching plays a crucial role in reducing operational costs and fulfilling operational targets in open-pit mining operations and is subject to large uncertainty arising from the operating cycles of trucks and loading equipment. This paper proposes a reinforcement learning-based truck dispatching system. Reinforcement learning is a machine learning area that deals with learning an optimal sequential decision-making strategy in an uncertain environment. An open-pit load-and-haul simulation is developed that also captures the truck movements and interactions in the shared road network, and a Neural Network is successfully trained to suggest truck dispatching decisions in a real-time manner.

Jun 25, 2023

By S. K. Kawatra, S. J. Ripke

Bentonite clay is used as a binder for iron ore concentrate pelletization. Bentonites are sensitive to cations such as calcium, magnesium, sodium, and potassium that are known to be dissolved in the moisture remaining in the iron ore concentrate. These cations affect the ability of bentonite to absorb water, as measured by the plate water absorbance (PWA) test. This paper addresses the relationships between plant water chemistry and pellet strength for a wide PWA range of bentonites. Experiments were conducted to determine the effect of concentrate moisture solute chemistry and bentonite PWA value on the wet knock and wet and dry compressive strengths of iron ore pellets. Experiments used seven different types of bentonite that had PWA values ranging from 564 to 1033. Flushing plant concentrate with distilled water to remove the dissolved cations resulted in increased pellet strengths, to a widely varying degree, for each bentonite tested; wet knock values increased an average of 92% and dry compressive strength increased an average of 46%. In addition, pellet strengths were not found to be directly related to the ability of bentonite to absorb distilled water, measured by the PWA test.

Jan 1, 2002

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990's. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By Rosario Lunar, Jesús Martínez-Frías, Egidio Marino, Trinidad Torres, Jose E. Ortiz, Juan A. Martín-Rubí, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

Seamounts, submarine banks, volcanoes and undercurrent channels are prominent geomorphic features that have become an important target for minerals research and exploration with the goal of future exploitation. Polymetallic ferromanganese deposits are common types of mineralization on these settings. Co-rich ferromanganese crusts are important as potential resources of Mn and Co, but also Ti, Ni, Tl, REEs, PGEs, and other metals. Many seamounts and channels along the Atlantic Spanish continental margin are known to hold mineral deposits but are poorly studied. This work presents and briefly describes the most recent activities of the Spanish Geological Survey (IGME) on exploration and investigation of ferromanganese deposits along the Atlantic Spanish continental margin. Different submarine areas from the northwestern margin of the Iberian Peninsula to the west off Canary Islands have been surveyed by geophysical, sampling and underwater observations from 89 to 4000 m water depth. The mineral deposits cover a large diversity of submarine geological and geomorphical features: mud volcanoes and diapirs related to hydrocarbon seeps, seamounts associated with hot spot volcanism, hydrothermal vents in active magmatic volcanoes, structural basement highs and banks or contourite channels. Considering the collected dataset, we present the preliminary results of the study of these mineral deposits, including ferromanganese nodules and crusts and phosphate pavements and nodules, which can be considered as potential sources of raw materials.

Sep 1, 2014

By L. Harris

The Yanacocha project is the first foreign investment in Peruvian mining since Cuajone during 1976. Three years after the project began, it has become the largest producer of gold from heap-leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha SA (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits. And it has attracted the interest of foreign investors in Peru’s mineral resources. Construction began on Aug. 1, 1992. The first gold bar was poured on Aug. 7, 1993 from ore from the Carachugo Mine. During 1993, Minera Yanacocha produced 2.5 t (81,000 oz) of gold and 9.4 t (304,000 oz) during1994 (40% above budget). Production was expected to exceed 15.5 t (500,000oz) during 1995 with the start-up the Maqui Maqui Mine.

Jan 1, 1996

In June, 1,334 underground construction and tunneling professionals gathered in Toronto, Ontario for the 2007 Rapid Excavation and Tunneling Conference (RETC). This biennial event, sponsored by SME, is one of the global underground construction industry?s major events. And this year?s RETC was the first one that included the new Underground Construction Association. [ ] (UCA) of SME. In addition, the conference?s exhibit attracted 125 equipment and service providers. The next Rapid Excavation and Tunneling Conference is set for June 14-17, 2009 at Caesar?s Palace, Las Vegas, NV.

Jan 1, 2007

By M. K. Larson

"Specialized numerical modeling codes have been developed over the years to estimate ground stresses during the excavation of coal in underground mines. One of these tools, MULSIM, a displacement discontinuity boundary element code, was last developed by Zipf into a version called MULSIM/NL [USBM 1992a, 1992b]. The code was used frequently in years past, but closure of the Bureau of Mines in 1996 marked the beginning of a pause in its development. A similar tool with distinctly different treatment of overburden idealization, LaModel, was subsequently developed [Heasley 1997] and largely displaced MULSIM/NL in the literature. However, recent work modeling deep western longwall coal mines [Larson and Whyatt 2013] has demonstrated that MULSIM has distinct advantages for regions with relatively stiff and strong overburden. This work required that MULSIM be revived and updated into a version called MulsimNL/Large. Updates include larger array sizes, greater precision, greater number of materials, and the addition of a five-point, six-segment pillar load/displacement model that provides the user a more flexible coal-strength model allowing hardening and softening before a final residual strength. MulsimNL/Large has the ability to calibrate to large load transfer distances observed in some western U.S. coal mines that appear to be caused by strong, massive units in the overburden and/or floor of a coal mine. Also, it provides the ability to calibrate gob stiffness to simulate measurements or estimates of overpanel weight distribution between gob and abutment, while still maintaining load transfer distance with minor adjustments. MulsimNL/Large can easily implement material strengths calculated from various pillar strength models. The five-point model gives MulsimNL/Large the ability to easily simulate pillar behavior that is extracted from detailed pillar models, such as FLAC3D. MulsimNL/Large or similar approaches should be considered for evaluating mining layouts where stratigraphic conditions are known to cause overpanel weight to transfer to an extent significantly longer than the empirical method widely used to calculate load transfer distances in the U.S. [Peng and Chiang 1984; Mark 1987; USBM 1990]."

Jan 1, 2015

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977