Search Documents

By Andre Vien, Frank Laroche, David Di Sandro

Back in 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution—size distribution relationship. This allows grade and recovery predictions from a varying mine plan via product size distribution predictions. This paper presents a case study where this elegant method has been used to build a very powerful forecaster at a process plant, built from historic operating data. The methodology has been used by this operation to forecast production on a quarterly, annual, and life-of-mine basis since the late 1990s. It has been upgraded several times to incorporate new drivers as the complexity of feedstocks has increased over the years.

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

Planning the primary development of a mineral deposit usually is done only once during the life of a mine. As a consequence, not optimizing the primary development of a mineral deposit can cause disadvantages over the whole life of a mine and can lead to higher costs. As a contribution to an improved primary development design procedure beyond the already existing work a study of the identification and quantification of the influence of parameters on primary development based on operational data from working mining operations has been completed. Based upon such a quantification of the influence of parameters a sequenced decision model was developed, that enables to develop an initial concept for the design of the accesses from the surface based upon a few critical parameters. Such a model will not replace detailed planning work within a feasibility study, but it is intended to reduce the amount of planning efforts at an early project stage through providing information what are most likely economic solutions, based on simple rules.

Jan 1, 1997

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By Andre Vien, Frank Laroche, David Di Sandro

Back in 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution—size distribution relationship. This allows grade and recovery predictions from a varying mine plan via product size distribution predictions. This paper presents a case study where this elegant method has been used to build a very powerful forecaster at a process plant, built from historic operating data. The methodology has been used by this operation to forecast production on a quarterly, annual, and life-of-mine basis since the late 1990s. It has been upgraded several times to incorporate new drivers as the complexity of feedstocks has increased over the years.

By T. M. Yegulalp

Geometric programming is a mathematical optimization technique, first formulated by Zener [1], for dealing with certain types of functions which typically arise in engineering design problems. The theory provides algorithms for finding the optimal solution, existence theorems by which one can show that a particular design is possible or not; and characterization theorems that especially make possible to obtain the relationships among the optimal design parameters at optimum. It has been demonstrated [2] that this technique can be applied to several design problems in chemical, electrical and mechanical engineering. Design problems in mining, metallurgical and mineral engineering have many aspects similar to that of other engineering problems. Thus it is only natural to consider geometric programming as a potential tool for solving certain optimization problems in mineral industries.

Jan 1, 1974

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By Syd S. Peng

Is the laboratory sized coal specimen much stronger than underground coal pillars? The answer to this question has a profound implication to many coal operators. It will decide how much of the coal reserve can be recovered. Or, in many cases, it will determine whether it can be mined economically. Recent trends in several eastern states to establish regulations regarding coal pillar design to prevent surface subsidence long after mining heighten the debates. And, in some cases, these trends highlight the existing practices that seriously question the conventional wisdom. Currently, nearly all researchers and practitioners agree that as the size of rock specimens increases, its strength decreases. This concept has been universally adopted as the basic principle for coal pillar design in the United States. Several formulas have been derived to account for this effect. The reduction factor for underground coal pillars ranges from one-half to one-sixth of the strength obtained in the laboratory, depending on the formula selected. Recent case studies indicate that the reduction factor is not justifiable, at east in some cases. The use of a reduction factor is based on the assumption hat smaller rock specimens as tested in he laboratory contain none or fewer fractures or planes of weakness than larger specimens or underground coal pillars. In other words, the larger the rock materials, the more fractures it contains and subsequently weaker in strength. Do all underground coal pillars have more fractures than laboratory sized coal specimens? Not necessarily. All coal contains cleats. Some are con¬spicuous but others are not. In terms of cleat density (number of cleats per unit area), there is no difference between an underground coal pillar and a laboratory sized specimen, provided the specimen size is larger than the cleat spacing, which is mostly 25 to 75 mm (1 to 3 in.).

Jan 1, 1993

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By B. Swarbrick

Today’s mining occurs in a dynamic world of conflicting objectives. Mining companies have to look further than a traditional cash flow analysis to determine the potential value of developing a mine. In particular, proposals for new mine developments undergo rigorous scrutiny by a variety of stakeholders including regulators, NGO’s, and the local communities. From a business risk perspective, how mining companies address stakeholder concerns can have a dramatic impact on the success of the project. In today’s mining environment mining companies must continue to ‘walk the talk’ to stay in business, particularly during downturns in the business cycle. Falconbridge’s Raglan Mine is an example of a project that was successfully developed in a region that is sensitive from many perspectives, including environmental, socio economic, and regulatory. Close working relationships with local stakeholders along with strong environmental management systems are necessary elements of continued success for the project.

Jan 1, 2000

By Thomas R. Kuesel, Harvey W. Parker

INTRODUCTION This paper describes the use of a shield and compressed air for construction of a short section of a pair of twin single-track tunnels for the Metropolitan Atlanta Rapid Transit Authority (MARTA) transit system. Although only two blocks long, this section posed the greatest difficulties to both engineers and contractors, and is the most expensive section of line construction on the MARTA system. All this derives directly from its setting--these tunnels had to be constructed through mixed-face conditions. SETTING The Broad Street tunnels form a link between the Peachtree Center and Five Points Stations, in the heart of Atlanta's central business district (Figure 1). Peachtree Center sits atop a solid rock ridge, which inspired the design of a deep rock-mined station, as described in the 1979 RETC. Five Points Station is MARTA's hub--the intersection of the system's two main branches. It is located in the old railroad gulch, a filled-in erosional valley at the base of Peachtree Ridge, and was constructed by open-cut methods. The alignment and profile of the Broad Street tunnels were closely constrained by these two adjacent anchors, and in the six-block stretch between them there was very little room for maneuvering. Since the rock ridge petered out about in the middle of the section, it was evident at the outset that there would be about two blocks of rock tunneling at the north end, two blocks of soft ground construction at the south, and two blocks of mixed-face in between. It is this central two-block section that is the focus of this paper.

Jan 1, 1981

By J. Alvarez, S. H. Castro

The feasibility of chalcopyrite-pyrite separation in the flotation of a chalcopyritic copper ore, at reduced surface tensions regulated by methanol, was investigated. It was found that with methanol dosages from 0.5% to 1.5% v/ v, the chalcopyrite might be effectively separated from the pyrite, without use of other flotation reagents and pH regulators. However, under this simple condition, the chalcopyrite recovery was only around 50%, recommending the use of other reagents to reinforce the collector action. Low dosages of different collectors were tested, including SF-323 (Shell Float), S-6588 and S-7251 (Cytec), and S-701 (Molycop). Very promising results were obtained with low dosages of the collector S-701 and 1% v/v of methanol in the pulp, which evaluated against a reference test, gave similar copper recovery, higher Mo recovery and higher depression of pyrite. Consequently, this is an alternative process which does not require the use of lime to depress pyrite.

Jan 1, 1995

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By William E. Mead

A regional investigation to find large supplies of potable ground water was carried out at elevations exceeding 12,000 feet above sea level on the Bolivian Altiplano. The program marked the first application of modern ground water search and development technology in the region, and ended a history of unsuccessful exploration efforts to locate important supplies of fresh water from underground sources. Oruro, a population center of 90,000 inhabitants, and its primary supporting industry - mining, both derived major direct benefit from the results of this program.

Jan 1, 1970

By Xuebin Liu, Yi Shang, Can Zhou, Hongqiu Zhu, Junbo Du

In the neutral leaching process of zinc hydrometallurgy, the pH value directly affects the leaching rate of zinc calcine. However, due to the complex mechanism of the leaching process and frequent fluctuation of working conditions, it is difficult to control the pH value by manual control. Therefore, this study proposes a fuzzy control method based on rule extraction under multiple working conditions, and analyzes the pH control performance. Firstly, the different operating states are classified according to process mechanisms and the Pearson method. Secondly, under the framework of the active learning algorithm, the approximate linear dependence (ALD) method is introduced to iteratively select samples with rule information in the original sample set for manual annotation. Then, the support vector machine (SVM) method is used to extract fuzzy control rules in different working conditions. Finally, a fuzzy rule set is established according to the samples mapped by the support vector. The simulation results based on industrial data show that the proposed method has better control performance than conventional fuzzy control and proportional–integral–derivative (PID) control.

Apr 1, 2024

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By S. Ersayin, I. Iwasaki

The application of a magnetic field was shown to be effective in controlling iron losses in a pilot-scale cationic silica fIotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42-m3 (50 cu ft) WEMCO flotation cell are reported. Major losses of iron units in froth products were in the -25-µm (-500-mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The "as-received" sample was sufficiently magnetized, and no further benefit was gained by the magnetizing treatment. The selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be readily installed in existing equipment. Key words: Iron ore, Flotation, Taconite concentrates, Cationic silica flotation, Magnetic field, Flexible magnetic sheet, Magnetizing, Demagnetizing

Jan 1, 2003