Search Documents

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By L. Shevenell, L. Stillings

The Acid Drainage Technology Initiative-Metal Mining Sector (ADTI-MMS) has established a Pit Lake Committee to enhance the science and understanding for the long-term management of pit lakes. Participation in this new committee is from members of federal and state agencies, industry, and academia, including numerous individuals representing 10 states. Work has begun on a pit lake literature search and review, database, classification, and sampling and monitoring procedures document. Coordination with the International Network for Acid Prevention (INAP) has been established. Future work will include preparing a prediction and assumption verification document, a report identifying variables upon which water quality is dependent, and an applied remediation technologies document, including an evaluation of the effects of backfilling.

Jan 1, 2002

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By Russell H. W. Chadwick

Reviewing events in the minerals industry, in economic geology, and in my own exploration work, I find that the most compelling subject for comment is the increasing ferment in ore deposits theory. New discoveries and continued investigations of bedded deposits of lead and zinc, copper, iron, uranium, etc., coupled with the availability of much new and significant data from sedimentary and metamorphic petrology, geochemistry, and oceanography, has led many economic geologists like myself to become disenchanted with former simplistic notions. Now disenchantment among serious people should presuppose both valid objections to the old, and valid new substitutes. I can sum up my own position and, I believe, what most of the recent writers on ore deposits theory are trying to tell us, by saying that a physico-chemical (bench science) approach to a natural science is neither correct nor useful, and that the obvious cure is a return to the study of the geology of ore deposits. More specifically, ore should be viewed merely as an unusual concentration produced, in stages, by the natural processes inherent in the geochemical cycle. In criticizing the conceptual basis of a science, one is involved simultaneously in the inherent character of the science, its subject matter, and the old and new concepts. I have found it impossible to make a clean separation along those lines. As a result, and as the title suggests, these are not-quite-random reflections on genesis, a matter near and dear to all true treasure hunters since Agricola.

Jan 1, 1967

By R. J. Sheets

"INTRODUCTION What is the primary responsibility for geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer – ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geo-engineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this paper will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face. WHAT IS OUR PURPOSE? A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question above. I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor groundwater levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: SAFETY. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or groundwater. The objective of a hydrogeologist is to ensure the soil or rock around an open pit or underground mine is dewatered; this specific objective will reduce pore pressures which could lead to a possible ground failure. They ensure a working bench/UG level is dry, so operations are not dealing with adverse conditions while mining. A geotechnical engineer is expected to use all available information and engineering judgement to provide design recommendations, so that the mine will not catastrophically fail. Additionally, they will implement the monitoring systems to identify hazards in advance in the event that the design is flawed and people need to be evacuated. We all know that safety is important to everyone; however, our particular set of technical skills play a significant role in ensuring the safety of a large portion of the global mining workforce."

Jan 1, 2018

By Zhang Zhitie

The limitations in mechanism research of mineral comminution in the past and the basic features of the comminution process have been analyzed. Two kinds of catastrophe model, i.e., cusp model and swallowtail one in the mineral comminution have been put forward. The dissipative structure of the mineral comminution: entropy production rate, extra entropy, extra entropy production and system stability has been discussed. The physical nature of the behavior that an old structure was destroyed and a new one was produced in the mineral comminution process has been brought to light.

Jan 1, 1995

By S. K. Nicol

Flotation, water-washing cyclones (hydrocyclones) and spiral concentrators are the three process units most commonly utilised in fine coal preparation. The results of testwork conducted on these three units will be presented and their performance and separation characteristics examined in detail. In particular, the dependence of the separation characteristics of each unit on particle size and the constraint this places on product quality (ash and sulphur levels) will be discussed. This dependence will be shown to be a critical criterion in the selection of fine coal circuits.

Jan 1, 1986

By Devan Naik, Matthew Stokes, Andy Nigro

This paper describes the surgical removal of a 24 ft dia. Slurry Shield TBM entombed beneath one of the country’s busiest commuter rail interlockings, the Harold Interlocking in Queens, NY, and the construction of the interface to a cut/cover tunnel which extended the mined tunnel section. A sophisticated SOE was built around the TBM to support active track loads within 8ft. of the excavation. Once the TBM head and guts were removed, a full round CIP lining was installed connecting the existing precast tunnel liner to the C/C tunnel under construction. All this construction was done on a narrow island of land without road access nestled between 7 mainline LIRR/Amtrak rail lines.

Jun 13, 2021

By H. R. Thompson

The Grant Town Power Plant is a nominal 80 MW (net) Waste Coal-Fired Electric Generating Plant which is located in northern West Virginia, approximately 15 miles southwest of Morgantown. The Steam Generator consists of two (2) Pyro-Power Circulating Fluidized-Bed Boilers (CFB), each rated at 400 000 lbs/hour @ 1,350 psig. Main Steam. The Turbine Generator is a single GEC Ahlstrom unit rated at 95 MW gross and 80 MW net. The Plant began commercial generation during April, 1993. The facility is owned by American Bituminous Power Partners, L.P. (AmBit), and operated by Mission Operations and Maintenance, Inc.

Jan 1, 1996

Those involved in the mining and minerals industry really are an optimistic bunch. Faced with an economic downturn that has spread across the globe ? one, some say, that crept up on everyone ? mining professionals remain hopeful that the industry will return. An example of that optimism is the attendance at two of the industry?s key conferences and exhibitions. In February, more than 4,200 people attended the SME Annual Meeting and Exhibit in Denver, CO. And a week later, in Toronto, Ontario, more than 18,000 were on hand for the Prospectors and Developers Association of Canada?s (PDAC) meeting. Both are respectable numbers and run contrary to meeting attendance figures during previous downturns when attendance and the numbers of exhibitors fell off significantly. Like other downturns, this most recent one has resulted in massive layoffs, curtailments of production and outright closures. Exploration has been hard hit and many junior mining and exploration companies will either disappear or be swallowed up by others. Gold is its usual self The PDAC generally attracts the gold mining and exploration sectors. So that might explain some of the optimism at the meeting. Unlike base metals and construction materials, gold, not surprisingly, is doing well. And most of the companies in the Investors Exchange at PDAC were involved with gold. While the balance sheets for most base metals companies look bad, gold companies appear to be not as hard hit. Gold is doing what it usually does during a downturn ? act as a safe haven while the value of other assets collapse worldwide. Governments around the world are preparing to pour trillions of dollars in an attempt to resuscitate their economies. This will likely lead to inflation, some experts at the PDAC convention said, which will be good for gold. And gold mining companies are also benefiting from lower production costs. The result is that some gold watchers believe gold could reach $64/g ($2,000/oz) at some point.

Jan 1, 2009

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By G. E. Jones, G. K. Hoffman

Through the USGS National Coal Availability pro-gram, two San Juan Basin studies have been completed. The study areas are in the northwest Bisti field, Fruitland Formation and in the eastern Standing Rock field, Menefee Formation. Original resources are 4.66 Gt and 3.46 Gt (5.14 billion stand 3.82 billion st), respectively, in the Bisti and Standing Rock areas. Bisti coal resources are greatly reduced by the Bisti-De-Na-Zin wilderness area (1.13 Gt (1.25 billion st)). Technological restrictions remove 31% from Standing Rock original resource. Available resources are 60% (2.79 Gt(3.07 billion st)) of the Bisti original resource and66% (2.26 Gt (2.49 billion st)) of the original Standing Rock resource.

Jan 1, 2000

By Charles B. Escapule

The first successful heap leach of silver ores in the State of Arizona has been under continuous operation since early 1976 at the State of Maine Mine, two miles southwest of Tombstone, Arizona. The silver produced from leaching old mine dumps at this property vas the first in the Tombstone mining district to achieve a 999+ purity. While cyanide leaching of silver and gold ores is a time-proven accepted practice, a relatively new method of treatment called "heap" leaching was employed. Heap leaching is a comparatively inexpensive fast way to recover precious metals from low grade material.

Jan 1, 1981

By M. Moats, J. Young

Short term laboratory cell electrorefining experiments were performed to examine the impact of electrolyte composition, current density and temperature on deposit structure, roughness, and adhesion to 2B mill finished 316L stainless steel. Copper electrodeposits were produced using synthetic electrolytes with thiourea and the continuous addition of glue. Deposit structures were evaluated using X-ray diffractometry. Surface roughness was measured using profilometry and analyzed using scaling analysis. Finally, an internally developed method was used to measure the force required to remove the electrodeposited copper from stainless steel to determine adhesion strength.

Mar 2, 2022

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By Graham E. Rawlings

Geotechnical investigations for underground projects are subject to a variety of constraints, including factors such as accessibility, geological complexity, thickness of oberburden and finance. As a result, the extent of geological data available for route selection and assessment of underground design and construction problems may vary between wide limits. It is essential that the data collected, the degree to which it is representative, and the confidence with which the problems can be anticipated, should be reflected in the type of contract set up and the way in which the contract documents are written. The paper addresses the methods by which investigations can be focussed to make suitable overall ground assessments for feasibility level studies. Subsequent investigations can then be objectively directed toward obtaining data on specific geotechnlcal problems or aspects which impact tunnel, cavern and shaft design and construction. The extent of investigations at the preliminary and design engineering stages must be closely related to the geotechnlcal surveillance and control during excavation. Fixed-price contracts necessitate a secure geotechnical data base prior to bidding, and the provision of that to the tenderers. By contrast, 'design-as-you-go' contracts minimize the geotechnical information needed before construction, yet require immediate assessment of the excavated ground for determination of support requirements and payment category.

Jan 1, 1983