Search Documents

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By C. R. Tinsley

Valuations can be molded, twisted and misinterpreted. Cases of spurious scope setting; limits to the information or access by the valuer; difficulties with the lack of comparative valuations; inappropriate valuation methods and outright speculations are described. None should be accepted by an experienced, independent minerals valuer. The Australasian Institute of Mining and Metallurgy (TheAusIMM) is working on a Valmin Code for which a Manual of Best Practice and Valuation Guidelines may be developed.

Jan 1, 1995

By Raymond A. Bradbury

Martin County Coal Corporation operates three underground mines and two surface mines on Wolf Creek in Martin County near Inez, Ky. The original underground development was begun in March of 1970. The property being developed is leased from Pocahontas Land Corporation. The A. T. Massey Coal Company, whose offices are located in Richmond, Virginia, is the parent company and sales agent for Martin County Coal. Duke Power Company is the customer who will take all the production from the mines which ultimately are scheduled to produce 2,500,000 tons annually. The Norfolk and Western Railway Company built a 24-mile railroad into this huge reserve of low-sulfur steam coal. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton seams are being deep-mined now and it is in three mines that the diesel haulage equipment is used. Those of you who attended the AIME meeting in Birmingham last October or the Diesel Symposium in Pittsburgh in January of this year are familiar with the introduction of trackless diesel-powered haulage equipment into our Martin County mines. I made a presentation at each of those meetings which dealt with our first experience with Wagner Mining Equipment haulage units. These machines are sold exclusively by Lake Shore, Inc. whose offices are in Iron Mountain, Michigan.

Jan 1, 1973

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983

By A. B. Cecala

Two recent Bureau studies evaluated workers' dust exposures in automated pallet loading processes. The first study involved a Bureau designed dust control system using a push-pull ventilation technique. The unit was shown to reduce workers' dust exposures by 76% during pallet loading at a ground silica operation. A hydraulic lift table was used to automate the bag stacking process; this kept the loading height constant throughout the entire pallet loading cycle. The second study evaluated different commercial automated pallet loading systems. These systems automatically stack the bags onto pallets, shrink wrap the pallets, and deliver the pallets to a fork lift pickup location. Results from a ground silica evaluation site indicated respirable dust samples taken were below the Threshold Limit Value (TLV) as established by the Mine Safety and Health Administration (MSHA).

Jan 1, 1990

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By Steve Hicks, Zach Agioutantis, Greg Hasenfus, Zach Wedding

Most prediction methods used to calculate mining-induced subsidence rely on empirical formulations, which typically assume flat topography and uniform properties in the overburden. It is also well known that when a longwall panel mines below a valley bottom surface ground deformation magnitudes and orientations may be significantly influenced by the presence of the valley. This paper discusses ground deformation data collected at different surface locations above the Buchanan mine in the eastern United States. Measurements at individual surface points and strata movement measurements using a three-point extensometer have been collected as the area was undermined. Measurements correspond to the mining of the panel immediately under the measurement points and to the mining of adjacent panels. Measurement locations correspond to valley bottom locations. The measurements are critically evaluated and compared with respect to topography and panel face location. The issue of the fluctuation of GPS measurements is also discussed.

Jun 25, 2024

By J. Andres, M. Cross

"Freeport-McMoRan’s Sierrita operations has two natural gas-fired molybdenum roasters for converting molybdenum disulfide into molybdenum trioxide. When these roasters were compared to other similar units within the company during a benchmarking exercise, it showed that increased throughput from the roaster units at Sierrita was possible. A team of site metallurgists, technical experts from other sites, and engineers from the Climax Technology Center was formed to study the potential in more detail. The team investigated many parameters in the roaster, including temperature profiles, roaster chemistry profiles, rabble and drop hole patterns, and operational strategies. The results of these studies and the associated throughput improvements are described in this paper. INTRODUCTION Molybdenum, a vital component for the steel industry, is typically found in nature as molybdenum disulfide (MoS2). MoS2 is typically recovered via flotation processes and is purified through leaching processes. While molybdenum disulfide is a commercial product, it is not the form of molybdenum that the steel industry requires. They require molybdenum in the form of molybdenum trioxide, MoO3. There are multiple ways to refine molybdenum disulfide into molybdenum trioxide. The primary method is the oxidation of molybdenum disulfide in a multiple hearth roaster. The chemistry of converting molybdenum disulfide to molybdenum trioxide is very favorable at increased temperatures, oxidizing the molybdenum through a range of exothermic reactions to ultimately produce MoO3. The chemical reactions that occur in molydenum roasting occur in three zones. These three zones correspond with four different reactions."

Jan 1, 2015

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By D. C. Edwards

In an age where customer service and quality drive today's industry and business, no service or product is exempt from these demands. Industry and business are streamlining everything from people to equipment and today have a heavier reliance on the performance and quality of their assets and equipment, (one of the keys to staying competitive). In the mining process industry, the centrifugal slurry pump is a key piece of equipment that keeps product moving and aids in generating revenue for its owner. The continued improvement and customer success lies in a team effort between the mining industry and the pump manufacturers. We, the pump manufacturers, need to keep improving our designs to further extend the life of our pump with fewer failures and promote to our customers proper maintenance of the pumps to continually keep unexpected failures to a minimum. Strict equipment maintenance, as thoroughly demonstrated by the military, is key to the long life and success of any piece of equipment. In the often harsh duty of the centrifugal slurry pump, maintenance is something that requires "attention to detail". No area of the pump is exempt from attentive maintenance. Here, discussions will focus on the areas of the mechanical drive end, wet end, seals, and extended pump shut down and start up. There has not been a slurry pump designed to maintain or repair itself. So in effect, each pump warrants able bodied maintenance persons to maintain them who continually observe all the rules of safety. Prior to any maintenance discussion or action, the issue of safety should always be addressed. Here, as with everywhere, the same rules apply. Work at a safe pace, note all safety precautions, use associated safety equipment and personal protective attire, observe all tagout and lockout procedures, and most importantly, be aware.

Jan 1, 1996

By John F. Clarkson

White Pine Copper Company built and operated, from August, 1962 through May, 1963, a pilot plant to recover copper using a cyanide percolation leach of the sand fraction (+400 mesh) of the mill tailings (1, 2, 3). The pilot plant runs were metallurgically successful and preliminary engineering studies for a full scale operation were completed under contract by an outside engineering firm. Unfortunately, the net return projected at that time did not justify the proposed capital' investment. In the summer of 1973 the project was revived. The rise in selling price of copper over the previous ten years, compared to the projected operating cost of the leach plant, increased the calculated net return on investment with the most recent figures showing a 30% DCF. Basically, the reason for this favorable shift in profitability was that the cost for many of the reagents did not go up as fast in the previous ten years as did the selling price of copper. Using the Chemical Marketing Reporter costs, NaCN sold for 18.3¢/lb in 1963 and 20.75¢/lb in August, 1973. During this same period H2S04 went from $23.50 per ton to $35.90 per ton. In comparison, producer's prices for electrolytic copper were 31¢/lb in 1963 and 619 in 1973. Thus the price of copper went up 97% while the two reagents only increased 13% and 53%, respectively. The capital investment also escalated but, again, not to the same extent as the selling price of copper. These price differences no longer are valid' but they did provide justification for reexamining the project.

Jan 1, 1975

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By K. Sample

Slope stability analysis plays an integral role in the design of various mining applications including waste dumps, heap leach piles, solution ponds, and tailings dams. Generally, limit equilibrium analysis using one of the several prevalent approaches is considered adequate. The density, saturation, and shear strength parameters of the materials forming the slope affect the failure mode and the calculated factor of safety (FS) against sliding. These parameters are generally based on laboratory tests. Field practices and construction procedures are often not completely simulated in the laboratory for various reasons (e.g. equipment limits, time and budget restraints, etc.). This paper presents a holistic assessment of slope stability analysis as practiced in mining applications, using example data from multiple heap leach projects. A sensitivity analysis is presented for variations in material properties, data interpretation, and computation methods. For each step in the design process, the possible variations in parameter values were identified and then used to perform traditional and probabilistic stability analyses. This simple, cradle-to-grave-type approach is used to evaluate the reliability of an example design, and the combined impact of multiple uncertainties on the factor of safety. Example Study The issue of addressing uncertainty in geotechnical design has been discussed in depth by numerous authors (Duncan 2000; Christian 2004; Whitman 1984; Christian et al. 1993). One may ignore the uncertainties involved in a design, take a conservative approach, rely on observational methods (Peck 1969), or attempt to quantify the uncertainty. Geotechnical projects in general, may include a combination of these methods. For important structures, such as heap leach pads, it is critical that sources of uncertainty in the stability analysis be acknowledged early on and considered in the overall design approach. As with any project, economics and other physical constraints, such as space limitation, often do not always allow for an overly-conservative, robust design. In an effort to quantify uncertainty and provide a sense of level of confidence in the safety and reliability of a design, probabilistic methods have been developed and implemented in many slope stability software packages. Reliability methods are often used in the design of open pit mine slopes, but not as commonly in designing heap leach pads and waste dumps. As an example, the stability analysis of a copper heap leach project is presented here to evaluate the effects of multiple sources of uncertainty and differing methods of data interpretation. Some of the parametric values, or the variation therein, are assumed on the basis of actual data from multiple heap leach projects, included in the paper as well. A generic representation of the example case study is shown in Figure 1. As depicted in the cross-section, the ultimate height of the design is 114 m (measured from the crest to the toe). The overall slope of the heap leach pad is 1.88 horizontal to 1 vertical (1.88H:1V), or 28°. The slope benches are considered in the overall slope. The example leach pad is founded on alluvial, colluvial and residual soils overlying weathered limestone. The ore to be placed on the pad is characterized as poorly graded gravel (GP) with average fines content (percent passing #200 sieve) of 4%. The liner subgrade is low permeability (fine) soil. The cover or the drainage material, placed directly above the geomembrane (between the liner and the ore), is crushed ore in this case. The phreatic surface was assumed to be 1 m above the base liner, which is what the collection system over the liner is typically designed for. [ ] In heap leach pads, typically, Linear Low Density Polyethylene (LLDPE) or High Density Polyethylene (HDPE) is used as the base liner. The decision is based on the elongation, strength and other requirements of the application as well as economic considerations. In this example study, the base liner was 80-mil single-side textured LLDPE. FIELD INVETIGATION AND SAMPLING When selecting appropriate values for the input parameters of the stability analysis, the level of uncertainty in the data and the assumptions that are made must be clearly identified and considered in the design. This concept has been emphasized through an extensive number of publications regarding geotechnical uncertainty and reliability (Christian et al. 1994; Duncan 2000; Christian 2004). The primary source of uncertainties involved in slope stability analysis for mining applications is inadequate geotechnical investigation, often lacking in a thorough assessment of in-situ material characterization and sampling disturbances. To emphasize this point, some background information is presented here. The tradeoff between the costs of a thorough site investigation versus the risks of design uncertainty has long been a challenging management decision in geotechnical projects. For mine sites, significant investment is typically made in exploration and estimating mineral resources and the geology of a mine site is often more thoroughly documented than other types of geotechnical projects. Nevertheless, the engineering properties of the soil and rocks relevant to slope stability receive less emphasis. Baecher and Christian (2003) observed that the areas of geotechnical concern, such as slopes and waste disposal facilities, are usually associated with mine costs rather than revenue, and therefore, significantly less money is devoted to their site characterization and laboratory testing. The expenditure for site investigations varies significantly from project to project, with higher levels of uncertainty and, therefore, the

Jan 1, 2009

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By A. Bruce Waugh, W. W. Wen, Kevin N. Clark, Neville C. Lockhart, Bruce A. Firth

Australia is the world's largest coal exporter, and technological advancement is a key element of the coal industry strategy. The issues include: increased recovery of saleable coal; enhanced quality, i.e. lower ash, moisture, fines, phosphorus (sulphur is a relatively minor problem for Australian coals); better quality control; higher throughputs/lower costs; improved handling and transport; and reduced environmental impacts. In process terms, many coal preparation operations, particularly fine coal circuits, are relatively inefficient, and all circuits must also be matched and integrated for optimum overall operation. A holistic approach to technological improvement is desirable. This paper summarises research and development efforts, within CSIRO and its collaborators, across the unit operations as outlined in the title.

Jan 1, 1995

By G. W. Heunisch

G.A. Carmody and L.B. Anderson We wish to comment on the paper by G.W. Heunisch (MINING ENGINEERING, January 1987), which raised several important points regarding treatment of acidic waste waters. This paper confirms, in part, tests carried out by Allyn Corp. Allyn is the manufacturer of the proprietary product Alka-Ment, one of the materials that Heunisch tested. The first point is the extreme sensitivity of the sedimentation rate on the nature of the treatment material used. This apparently results from differences in nucleation of the metal hydroxides, and is consistently higher for Alka-Ment. This decreased sludge volume is also observed when Alka-Ment is combined with flocculants, such as organic polymers (see Table 1). Our second point is to emphasize that Heunisch's work shows how dependent the sludge volume is on pH. It is common practice to overtreat AMD by raising pH to 9 or 10. This practice, in addition to being wasteful of material, actually decreases the density of the resulting sludge, probably by creating charged particles that do not readily coalesce. When treating with Alka-Ment, we recommend that the treatment be monitored by testing both pH and dissolved iron. For both tests, it is important to allow adequate time to elapse between treatment and measurement, so that dissolution of alkali, aerobic oxidation of iron, and precipitation of the metal hydroxides are nearly complete. Our tests have indicated that from 30 minutes to one hour is commonly required. Only in this way can a minimum pH be attained, with adequate treatment, denser sludge, and lower treatment rates achieved. Thirdly, Heunisch correctly recognizes that ASTM titration of Alka-Ment does not reflect the true treatment value available in a unit of Alka-Ment. Our work at Allyn indicates this is a most important consideration when evaluating various materials for the treatment of acidic waste waters. While we were unaware of Mr. Heunisch's work, we welcome comparisons between Alka-Ment and any competitive products readily available for field use. Allyn has hundreds of hours of laboratory and field data we are ready to share with interested parties treating acidic waste water.

Jan 9, 1987

By M. F. Dibble

The Fosfago phosphate rock concentrator is located in the state of Goias, Brazil, 300 km south of Brasilia. The ore is from an enriched carbonatite, which was discovered in 1971 during exploration for pyrochlore niobium ore. The flowsheet was developed in Brazil by personnel from Agrico Chemical Company and Consolidated South America. Engineering was provided by Codemin, a subsidiary of Consolidated, Engineering and construction management was pro- vided by both Agrico and Consolidated personnel who formed the Fosfago team. The concentrator was designed for 500,000 tpy of 37-38% P2Oj dried product. The facilities consist of open pit mining, crushing, stockpiling, and concentration. The product is pipelined seven km to a filtering, flash drying, and railroad loadout station. The plant was successfully started in May 1979.

Jan 1, 1980

By M. Deul

For the first half of the 21st Century the USA will rely on the same mix of fuels as for the past 50 years: Petroleum will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in severe stress on gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging ‘piggy-back’ trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002