Search Documents

By Roger Malmström, H. Heden, Kjell Lidin

INTRODUCTION LKAB was formed at the turn of the century when the railways between the ore fields and harbors were built. The mines are situated north of the Arctic Circle in Sweden. Kiirunavaara is the largest mine, with a pro¬duction capacity of approximately 30 Mt/a. Malm¬berget has a capacity of about 12 Mt/ a. Both are under¬ground mines. Svappavaara, the only opencast mine currently in operation, has a capacity of about 4.5 Mt/a. The ore harbors are at Narvik for the Kiruna and Svappavaara mines and at Lulea for the Malmberget mine (see Fig. 1). Production in the form of finished products is shown in Fig. 2a, b, c, and d. Due to poor ore markets in re¬cent years, production and shipments have been cut back, but there was a positive swing in 1978. LKAB has been 96% state-owned since 1957. In addition to the iron mines in northern Sweden, LKAB has subsidiaries in central Sweden which produce sulfide ores, quartz sand, and uranium (Fig. 3). The mining methods employed are opencast bench stoping at Svappavaara and sublevel caving at Kiirunavaara and Malmberget. GEOLOGY The Kiirunavaara ore body is 4000 m long and av¬erages about 90 m wide, with variations in width from a few meters to around 150 m. The ore has been ex¬plored by deep drilling down to about 1000 m, but mag¬netic measurements indicate a depth of at least 1500 m. The Kiirunavaara ore is oriented in a north-northeasterly direction with a number of ores in the boundaries be¬tween the wall rock types. The ore in Kiirunavaara is mainly a fine-grained magnetite with a varying content of fine-grained apatite. The apatite content of the ore decreases with increasing depth. The other ores are all apatite-bearing and a couple are hematite ores (Fig. 4a, b). The ores are sedimentary, tilted, and tectonically de¬formed. They have a lateral dip of 0.87 to 1.2 rad (50 to 70°). The contacts between ore and wall rock are distinct and sharp, but both the hanging wall and the footwall are brecciated and impregnated with magnetite. The footwall of the Kiirunavaara ore consists of syenite porphyry with a low quartz content and rela¬tively good strength; the hanging wall consists of quartz porphyry. Both types are known as Kiruna porphyries. The ore at the boundary with the hanging wall is often rich in kaolin. There are a few veins of syenite porphyry running through the ore, which has a few major faults (Fig. 4c, d). There are two sharply delineated ore grades in Kiirunavaara: low phosphorus ore with less than 0.1 % phosphorus (about one-third of the ore) and high phos¬phorus ore with greater than 0.5% phosphorus. The iron content is 67% in the low phosphorus ore and 60% in the high phosphorus ore. These ore types are sold as different grades and so are kept separate during mining. MINING AT KIIRUNAVAARA The Kiirunavaara and Luossavaara ores were first mined using opencast bench stoping in 1902. When mining costs rose owing to higher waste removal, under¬ground methods were adopted. In the mid-1950s, the ores were still being mined on the surface at the same

Jan 1, 1982

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Richard Giffen, Michael Trabold, Pablo Lemus

"As part of the new 2nd Ave Subway Project, an existing tunnel constructed in the 1970’s will be connected to the new subway and used as new running tunnels. The existing tunnel had to be modified to comply with newer structural and fire life safety codes and to be connected to the new cut and cover station at 96th St. This paper will discuss the complexities of tying an existing tunnel constructed over 40 years ago into the new station and allowing for movements due to the unloading of the existing tunnel and the differential settlement of the two structures during both the construction and permanent condition. Topics that will be discussed include structural analysis, ground improvement techniques, selection of support of excavation walls, working in contaminated soil and instrumentation and monitoring of the structures. It will also cover retrofitting the tunnel to comply with updated Fire/Life/Safety requirements. PROJECT OVERVIEW The Second Avenue Subway (SAS) will be the first major expansion of New York’s subway system in over 50 years. To be constructed in four phases, it will run from 125th St. in Harlem to Hanover Square in the Financial District (see Figure 1). For most of its length, the alignment is directly under the Second Avenue roadway."

Jan 1, 2016

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By William Bogan, Mark Vaivoda, Richard Daniele

Many factors must be considered when performing engineering and construction work for a major minerals project. Dravo's Afton copper smelter in British Columbia illustrates some of the E&C factors considered when setting up this new operation. In March 1978, Afton Mines Ltd., a Tech Corp. subsidiary, began blister copper production at the world's first integrated copper ore mining, milling, and smelting operation to use Top Blow Rotary Converter (TBRC) process smelting technology. This key TBRC smelting element is licensed by INCO Ltd. to Dravo Corp. The TBRC process uses a single vessel of modular design. It rotates for mixing and provides complete processing capability, from concentrate through blister copper. The Afton facility is about 16 km west of Kamloops, a town in south-central British Columbia. To make its operation as economic as possible, Afton officials considered several options for the copper smelter, the first in modern times in the province. Inability to extract precious metals-primarily gold-from the concentrates ruled out hydro-metallurgical processes. The final choice was between a conventional electric furnace/ Peirce-Smith converter combination and the TBRC process. The TBRC process was chosen for its versatility in processing the various Afton concentrates and grades and its 40% lower capital cost compared to the electric furnace converter system. The TBRC smelter -including concentrate slurry receiving, drying, storage, smelting, off-gas cleaning, and copper casting-had an installed cost of about $25 million. In December 1974, a pilot program was conducted by Teck, Dravo, and INCO at INCO's Port Colborne, Ontario, research facility. The pilot program demonstrated the TBRC's ability to smelt, convert, and clean copper slags. After the successful pilot effort, Dravo performed additional research to find an effective fixation system for high grade, intermittent SO2 gases. Once the go-ahead was given, design and procurement for the Afton copper smelter was provided by the Denver Division, Dravo Engineers and Constructors. Commonwealth Construction, Vancouver, constructed all Afton facilities. Afton's single furnace smelter is designed to produce 25-kt/a blister copper in 363-408 kg cake form. The product is sold to England for electrolytic refining. The TBRC process is only one of several innovations proposed by Dravo and chosen by Afton to insure the most modern smelter in North America and meet all British Columbia's environmental restrictions. Conventional smelting methods use a separate furnace for each process step. The TBRC process employs but one furnace. The Afton TBRC vessel measures 6.4 m in length and 4.3 m in diameter. The furnace is supported on a set of motor-driven rollers. These permit the vessel to rotate at variable speeds to 40 rpm. Rotation provides good mixing, high reaction rates, and effective heat transfer from the refractory sides to the molten bath resulting in a low thermal gradient. The furnace can tilt through a full 360° for charging, firing, and pouring. Smelting at Afton is accomplished in sequential fashion. Flotation concentrate and limestone flux are initially charged to the hot, empty vessel. Using the water-cooled, oxy-fuel lance, the initial charge is smelted. Once sufficient molten bath is obtained and slagging completed, the metallic concentrate is charged. Materials are charged through the water-cooled, variable position additive chute mounted on the TBRC

Jan 10, 1980

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. High-grade Transvaal chalcopyrite was neutron irradiated in a TRIGA reactor to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes during which time significant anomalies were observed. First, an initial period of rapid dissolution lasting a few minutes; second, an arrest or "plateau" region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effect of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured. The initial rate data were correlated by considering the rapid reaction to be due to the dissolution of surface oxidation products or the formation of an iron depleted surface layer. The data for the second slower reaction have been explained to be due

Jan 1, 1972

By Jeffrey Peterson, John Beesley, Martino Scialpi, John Cassidy

The DC Clean Rivers Project is DC Water's ongoing program to capture and treat combined sewer overflows (CSOs) during rainfall before they reach the District waterways. The Anacostia River system was designed to reduce CSOs into the Anacostia River and includes the Blue Plains Tunnel, Anacostia River Tunnel, First Street Tunnel, and Northeast Boundary Tunnel. A portion of the Anacostia River system was commissioned in March 2018 and the final component, the Northeast Boundary Tunnel, was placed in operation on September 15, 2023. This paper provides a summary of the experience gained during construction of this +$2.9 billion project, an overview of the system performance since its activation in 2018, and a look-ahead to the next phase of the DC Clean Rivers program: the Potomac River Tunnel.

Jun 23, 2024

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By J. Organiscak

A majority of continuous mining machines employ a water spray system and a machine-mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine-mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays and scrubber airflow on dust and gas levels, while using a 12.2-m (40-ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1-m (20-ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complement the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off-curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty&apos;s and early seventy&apos;s, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70&apos;s to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By O. Guyot, A. Broussaud, J. Björkman, P. Söderman, P. O. Samskog

Model-Based Expert Control systems (MBEC) are on-line supervisory dynamic optimization systems which combine the ability of a phenomenological model to generate a large amount of information about the state of the process and predict its evolution, with the flexibility of a rules-based approach to take plant constraints into account and apply a complex control strategy. For its new concentrator started in 1995 in Kiruna (Sweden), LKAB has implemented a progressive grinding flowsheet with closed-circuit autogenous grinding followed by closed-circuit pebble grinding with ore pebbles. The standard for instrumentation in this new plant is very high. The control hardware consists of a Distributed Control System (DCS) through which the operators interact with the plant, supplemented by a site-level Management Information System (MIS). A state-of-the-art MBEC system was imbedded in the MIS by the authors before plant start-up. It consists of several modeling and expertise software modules: a phenomenological process model and a Kalman filter estimate continuously the state of the process, an optimizer calculates an optimum feedrate, while rules-based modules establish production targets and key process set-points. The decision to install the MBEC system as an integral part of the new plant before start-up illustrates the current maturity of the technology, i.e., enough know-how was accumulated through former projects to design and develop the system to a large extent without accessing the plant. The feasibility and the power of dynamic optimization systems were previously demonstrated in Kiruna pre-existing concentrator by the authors. First, a MBEC system was installed on the three existing pebble mill circuits, providing both an increase in quality (stabilised size distribution) and a 10% increase in capacity. An on-line expert control system with limited modeling capabilities was also installed in the existing flotation plant, with the aim of stabilizing phosphorous content in the concentrate and optimizing collector additions. Both objectives have been achieved.

Jan 1, 1995

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery through- put target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer plant management system in the concentrator. The overall/philosophy was to keep the implementation simple while using new technology creatively.

Jan 1, 1991

By V. M. Torres

An empirical correlation to detennine laboratory mill grinding time has been developed. Grinding samples to 90 ± 5# below 147 micrometers was required for a flotation testwork at Companhia Vale do Rio Doce (CVRD) Research Center. The initial samples were all below 1 mm in size with different size distributions and work indices (Wi) ranging from 13 to 23 kWh/st. Grinding curves were determined for some initial samples. A correlation was developed between percent retained on 147 micrometers at a standard time and the time required to grind each sample to the required size. This correlation was then used to grind all samples, based on the preliminary grinding model. Finally, a statistical analysis with the size distribution of all samples was performed. The success of using the correlation was confirmed and an equation was determined using the data set.

Jan 1, 1996

By Z. Hajnal

Three years ago a research program was initiated at the University of Saskatchewan to develop seismic surveying techniques for use in the Precambrian geological environment. The success of the reflection method in many younger geological settings suggested that this is the technique which would be the most suitable for experimentation. A successful adaptation of this technique to the Shield environment would make mapping of rock formations possible to much greater depth than is possible at the present time with any other applied geophysical technique. This presentation attempts to illustrate the advances which have been made in this program and will provide some insight into future plans. The field investigations were limited to the Flin Flon basin near to the town of Flin Flon, Manitoba (Fig. 1). This area was chosen because the surface geology has been mapped in great detail and it is a very important base metal producing region. It is an ancient sedimentary basin with some characteristics similar to areas where the reflection method has been successful.

Jan 1, 1976