Search Documents

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By B. S. Treiber, R. A. Lohnes, S. M. Levorson

As part of a research program to develop a coal-handleability index that would predict the ease with which a coal would flow through a handling system, an apparatus was developed to directly measure the unconfined Yield strength and bulk density of consolidated-coal samples. The new test apparatus provides a fast and simple method for determining the strength and compressibility parameters that are associated with the handling characteristics of crushed coal. Comparative tests were conducted using a low-stress triaxial-test apparatus. To check the accuracy of the new method, four coals with a variety of moisture contents and gradations were tested using the new method. These tests indicate that the new test device yields valid results. Further, the speed and ease of operation of the new device makes it suitable for quality control and quality assurance in plants.

Jan 1, 1996

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By William Gleason

With its 2011 acquisition of rival equipment company Bucyrus International, Caterpillar added underground mining and large shovels to its line of products and further solidified its standing as the leading mining equipment manufacturer in the world with solutions for every aspect of mining. When Caterpillar spent $8.8 billion to acquire Bucyrus, the global mining business was flourishing, as mining companies around the world worked to keep up with demands for nearly every commodity. Flash forward to 2013, and the global mining landscape looks very different. Lower demand for raw material from China and India and falling commodity prices have forced most mining companies to pull back on their production. The reductions from the mining industry have hit equipment makers like Caterpillar and Komatsu hard. In October, Caterpillar reported that its quarterly earnings had fallen 44 percent. The changing conditions have also changed the narrative from Caterpillar and other equipment makers to customers from offering solutions to move the most tons per hour, to now offering solutions for the lowest cost per ton. In September, Caterpillar hosted some of its mining customers and the trade press at its Tinaja Hills Demonstration and Learning Center near Tucson, AZ to talk about its range of products, from its MineStar System designed to help increase efficiency through better equipment management and planning, all the way up to the massive Cat 7495 and 7495HF electric rope shovel lines acquired through the Bucyrus takeover

Dec 1, 2013

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By J. F. T. Agapito

Significant increases in extraction ratio on the order of six to eight percent, equivalent to as much as 142 t/m of panel advance, have occurred at the Big Island Mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-laying trona beds at depths of 250 to 260 m in the Green River Formation in south-western Wyoming.

Jan 1, 1988

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By Robert F. Kehrman

As part of the Bureau of Mines research on the In-Situ Uranium Leaching, various geophysical resistivity measuring techniques were -evaluated to identify a rapid reliable method for detecting the underground migration of lixiviant outside of the planned limits. Surface and downhole galvanic resistivity and controlled source audio-magnetotelluric (AMT) methods were tested at an in-situ uranium mine in Northern Wyoming during start-up of a new mining area. Downhole galvanic and AMT were the most promising techniques.

Jan 1, 1980

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By Steven McCutcheon

As most of us have learned through prior and often frustrating experience, anyone proposing to construct a new or expanded mining-ore processing facility must first contend with a rather complex array of environmental laws and permitting regulations administered by a number of different Federal, State and local agencies. At our lost count, there were about 55 federal enactments affecting base and precious metals projects. Applicable State and local laws will usually increase that number significantly. The time and costs associated with complying with all these various regulatory programs usually constitutes one of the major areas of uncertainty in the development of a proposed project. There are many in the mining industry who firmly believe that these environmental regulation and permit programs necessarily causes significant delays and increased costs in the development of a project. This belief, unfortunately, is probably a result of a basic misunderstanding of how the environmental permitting and regulatory system actually works.

Jan 1, 1984

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By Martin C. Kuhn

The use of tritium in manufacturing and its subsequent loss to the local environment in Tucson, Arizona resulted in a great debate relative to the physiological effects of low level radiation. This paper reviews some of the facts of the release and attempts to quantify the degree of hazard encountered by the local community. Some of the difficulties in assessing the true degree of absorbed dose and the assumptions necessary for calculation purposes are presented.

Jan 1, 1981

By P. C. Miller

The paper reports laboratory results from the bioleaching of chalcopyrite ores and concentrates using a mixed moderate thermophile culture. Copper dissolution in excess of 95% was achieved in all cases with the majority of tests indicating copper dissolution in excess of 98%. Aspects of downstream processing are discussed in relation to iron rejection by precipitation. The laboratory results indicate the need for careful control of the pH value to prevent co-precipitation of the copper with iron. A comparison of capital and operating costs is given indicating potential differences between the use of toll smelting and bacterial leaching on site. A discussion is given highlighting the sensitive cost areas of these two process routes.

Jan 1, 1997

By V. G. Medina

The 15 000 t/d La Coipa mine initiated operation in July of 1991. The complex consists of a conventional, open-pit mining operation and a mill employing cyanide leaching with Merrill-Crowe gold and silver recovery. The process plant includes a primary crushing circuit, a 15,000 t (live) covered stockpile, a semi-autogenous mill/ball mill/crusher or SABC grinding circuit, a leach circuit, a belt filtration/washing circuit, a zinc precipitation circuit and a "dry" tailing disposal system. The process plant is described in detail with major design considerations used in the selection of the processes and equipment. The unique methodology employed in the disposal of the filtered tailings is also described.

Jan 1, 1992

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962