Search Documents

By M. Brändström, R. Dube, J. Moyo, T. Perkins, G. Bermudez, L. Bartsch, C. Smith, R. Sorensen

The Kennecott Copperton concentrator is currently the bottleneck for the Kennecott operation and several projects have been initiated to increase throughput. This increase in grinding circuit throughput has resulted in a coarser grind size which has impacted flotation circuit recovery. Metso Outotec 300m3 forced air tank flotation cells are currently utilized in the rougher flotation circuit at the Copperton concentrator. Higher overall recoveries have been observed on the newer Outotec tank cells compared to the original 85m3 self-aspirated flotation cells they replaced. However, coarse particle flotation response on these large, forced air cells did not show encouraging results when compared to smaller previously installed cells. This coarse recovery loss has been attributed to the longer froth transport duration and transport distance on large cells (100m3 and larger). Cell manufacturers addressed the risks of additional coarse particle losses in large cells by installing concentric circumferential launders and crowders (also called center launders). These are designed to reduce froth transport time and distance in the last cells in rougher stages where low residual floatable minerals causes a lack of froth mobility. The center launders also increase froth crowding, which also helps to increase froth transport velocity and increases copper and molybdenum recoveries. A trial set of the center launder retrofits were installed on the last three tank cells in one of the parallel rougher flotation rows at Copperton. The launder retrofits were installed at the end of October 2020 and monitored until March 2021. This six-month trial showed statistically significant improvements in copper and molybdenum flotation recoveries through the rougher circuit.

Mar 2, 2022

By Donald G. Foot

The Bureau of Mines, U.S. Department of the Interior, devised a direct flotation method for treating low-grade carnallice (KC1.MgC12. 6H20) and sylvinite (a mixture of KC1 and NaC1) ores characterized by a high content of water-insoluble impurities. The procedure consists of (1) flocculation-depression of the insoluble slimes, (2) decomposition leach (carnallite only), (3) potash rougher, cleaner and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid-phase KC1 from carnallite ore and 79.7% of the KC1 from sylvinite ore in final products containing 60.5% and 60.9% K20, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1981

By Calvin R. Davis

The bucket elevator is probably the oldest known form of conveyor. Its history can be traced back to the days of Babylon where wicker baskets lined with a natural pitch and fastened to ropes operating over wooden sheaves turned by slaves, were used for the elevating of water into irrigation ditches. It is not unnatural for the bucket elevator to be the first in history, for even today engineers and designers recognize that well designed, correctly applied bucket elevators offer unequaled advantages over other bulk material elevating methods. The bucket elevator's vertical design saves valuable floor space. It provides flexibility of machinery layout with lowest initial capital expenditure, which is its principal advantage. While the advantages of the bucket elevator have long been recognized, there has been a tendency to lean away from its use because of high maintenance without reliability. CHAIN Belt Company found that the bucket elevator, if correctly applied, can be built to be as dependable and reliable as any other piece of machinery in today's modern processing plants. It is not difficult to understand why the bucket elevator is looked upon sometimes as a necessary evil in the material handling system. Very little has been published or written about the specific use or application of bucket elevators other than in manufacturers catalogs. Most of today's elevator application was set forth at the turn of the century by Hetzel (1). There have been many improvements made in the manufacturing techniques of elevator components, improvements in material selections, all which can be used to improve today's bucket elevator. To best understand the improvements which have taken place recently in the design and application of bucket elevators, an understanding of basic elevator principles is desirable. In general, it can be said that bucket elevators are classified into two basic types : (1) centrifugal discharge and (2) continuous. Elevators in use today are either of the centrifugal discharge type or the continuous type, or a combination of both in special applications.

Jan 1, 1958

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By David R. Kalasky

One of the primary areas of computer application in mine ventilation has been the analysis of mine ventilation networks. A variety of network analyzers that are aimed toward the solution of flows in a given network has been developed. These programs typically use the Hardy Cross or other iterative algorithm for solution of any network, even those that are complex. The computer software has become more efficient and sophisticated over time and has thus been widely adopted for ventilation network analysis. One of the shortcomings of these programs is that they have been developed with the idea of analyzing the ventilation requirements at a single point in the lifetime of a mine. This provides the ventilation engineer with an important tool for analysis but falls somewhat short of providing a convenient means to economically com- pare alternative methods for ventilating a mine. The program described in this paper provides such a tool. The principal concepts that were necessary for the completion of a computer program that analyzes ventilation alternatives is the capability of efficiently determining the ventilation requirements at a variety of times during the lifetime of the ventilation system and some method of analyzing the costs of the alternatives on a realistic comparative basis. To accomplish this task, the authors began using Penn State's mine ventilation simulator designated as PSU/MVS, Didyk et al. (1977a, 1977b) and added the necessary additional software to accommodate the need for multi-period, time-dependent analysis of the net- work. The software was then tested on a coal mine ventilation problem with a 23-year life. The problem points out the value of such a program for ventilation analysis.

Jan 1, 1986

By John Wiebmer

Six industry trends will have significant effect on the way mining equipment is designed and supported in the years ahead: 1. MINING IS MIGRATING TO LESSER DEVELOPED PARTS OF THE WORLD The global recession of the early 1980's drove down commodity prices and intensified cost competition. This caused a fairly dramatic trend in mining away from higher cost operations in developed countries to richer, lower cost deposits in developing countries. Miners operating in lesser developed parts of the world will place higher value on rugged, durable designs that can live in more difficult and sometimes abusive conditions. They need engines and power train systems that are more tolerant of a wide variation in fuel quality and oil specifications. They'll require machines that are simpler to operate, simpler to maintain, simpler to troubleshoot and simpler to repair. And they'll require creative means of support in getting technical information, parts and components to remote operational sites. Mining equipment in the future will be more durable and simple than it is today, and product support will grow in importance as purchasing criterion. 2. THE MINING INDUSTRY IS CONSOLIDATING An intense amount of corporate acquisition and industry consolidation activity is occurring, to the point that today just 50 mining companies account for 55% of the western world non-fuel mineral production. Consolidation will continue, leading in the future to an industry structure weighted heavily toward a few key global mining houses.

Jan 1, 1993

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By R. J. Visintainer, J. M. Furlan

"Due to the time-consuming nature of froth testing in a laboratory environment, practical limitations require the development of a method of applying a single set of performance test data (Visintainer and Whitlock, 2012) obtained for a single froth pump at a given speed to a range of froth pump speeds and sizes, % air content and liquid viscosities. Head, efficiency and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique that can be used to interpolate from existing test data in order to predict froth performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal, as well as the insights gained from analysis of the resulting regressions, are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute standard for the effects of liquid viscosity on centrifugal pump performance (ANSI, 2010).IntroductionPump performance data (Visintainer and Whitlock, 2012) has been collected for a froth pump using an experimental loop outfitted with an array of pressure transducers, mass flow meters, an inverted U-loop, magnetic flow meter and an assortment of other instrumentation. Experiments were performed on pure water, water and air, pure corn syrup, and corn syrup and air. Data was obtained for % air contents of 0-30% and viscosities of 1- 15,000 cSt at eight specific valve positions (eight different flows as a percentage of best efficiency flow points) and the viscosity was changed by allowing the system temperature to increase during testing. The test pump is a 710-mm diameter impeller, GIW HVF, open shrouded, vented design that has its discharge axis oriented at 45° upward from the horizontal. A schematic diagram of the froth pump test loop can be seen in Fig. 1."

Jan 1, 2015

By Z. Yanni, W. Xuan, Z. Jingyu, D. Jun

"In order to conserve the coal resources, many coal mines which have been mined begin to re-mine. Re-mining face is of complicated circumstances and coal spontaneous combustion is unknown, so experiments are designed to study the characteristics of multiple oxidized coal samples. The investigation into the oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. The non-caking coal is collected as coal samples. The raw coal sample with initial oxidation and the sample after second oxidation and third oxidation are obtained after a certain treatment of the coal. The temperature-programmed system, and proximate and ultimate analysis are adopted to compare the releases of gaseous products of spontaneous combustion characteristic parameters of the multiple oxidized coal sample. With the increase of oxidation times, experimental results indicate that the oxygen consumption rate, the release rate of carbon monoxide and the intensity of heat release are significantly decrease. The characteristic temperature dropped and the size of the pores in coal is smaller as well. INTRODUCTION China accounts for 13% of global coal resources [1-2]. In recent years, more and more coal mines begin to re-mine in order to conserve resources. This production mode is to mine coal pillar left by last exploitation or unavailable for mining. In the process of slicing mining for coal seam groups or thick coal seams, the second or multiple oxidation due to the mining-induced effect, may take place in the goaf of the lower seam. So the spontaneous combustion is prone to occur in this area. The study on oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. Scholars [3-7] have discussed the workability of re-mining for coal mines, verify the feasibility of the existing mining technology for re-mining area, and set up the prevention measures of coal spontaneous combustion. But all these measures are only based on on-site observation data, instead of experiment on spontaneous combustion characteristic parameters of re-mining coal samples which have a great importance for early prediction and forecast. The authors aim at investigating the multiple-oxidated coal spontaneous combustion law, and perfecting the coal spontaneous combustion mechanism to provide a basis for the prediction and forecast."

Jan 1, 2015

By J. B. Knaebel

I have been asked to discuss the "Development of the Twin Buttes Mine for Production." This property, which is a large low-grade open pit copper mine about 25 miles south of Tucson, Arizona, was recently brought into production by The Anaconda Company under a long-term lease agreement with the Banner Mining Company. Since the scope of this paper is limited to the subject broadly indicated by its title I will confine discussion of historical, environmental and other general matters to a brief summary sufficient, I hope, to establish a background of those conditions which influenced our approach to the technical and economic problems that faced us at Twin Buttes. The paper deals primarily with our studies and activities related to the solution of these problems and with the resulting engineering and business decisions that were taken - decisions which culminated last September in the initial commercial operation of another major open pit copper producer unique and interesting in several respects.

Jan 1, 1970

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By J. L. Boyd

The mining and processing of basic metals relies on water as a medium for transport. Metallurgical ores are ground, concentrated, leached and refined in an aqueous medium. Water is used for temperature control during processing and in air pollution abatement during smelting. All of these process steps result in liquid wastes. Many of the aqueous wastes from ore processing areas become the raw product for a second stage and water recycling may begin. The point at which water recycling or reuse has been initiated in the past, rather than water discharge, was where water conservation was manditory due to a shortage, where process conditions would allow or benefit from reuse, and where economic considerations demanded reuse. The Fontana, California plant of Kaiser Steel Corporation is an example of an integrated steel plant that was forced to practice water conservation and reuse due to its location in an arid environment.1 Only a small amount of water required to maintain the water reuse system in balance with respect to dissolved solids and product quality is discharged. The Butte, Montana copper ore processing plant of The Anaconda Company obtains 66% of the water required for production by recycling, after clarification and chemical treatment, 30 MGD of wastewater from its tailings ponds. This operation is estimated to save the company about $1200/day over a once through water system.2 Here plant location and economics favored water reuse.

Jan 1, 1975

By F. F. Peng

A unique collector dispersion techniques was developed and used to improve the flotation rate and recovery of coarser and ultrafine coal-rich particles in the froth flotation processes. In this novel collector dispersion method, the collector such as hydrocarbon-oil is gasified and transported by gas phase (air stream) into the pulp. In addition to the excellent mode of collector dispersion, the collector-encapsulated air bubbles are generated in the pulp. This approach alters the surface properties of air bubbles and provides the fast rate of flotation compared to that of direct liquid collector addition froth flotation. Using gasified kerosene as the collector, the effect of altering surface properties of bubbles on the recovery of larger and finer coal-rich particles of -1.7 mm (-12 mesh) and -600 µ m (-30 mesh) raw coal samples were studied. The Redstone seam coal obtained from Northern Central region of West Virginia was used in this work. The effect of particle size on oil-coated bubble flotation rate and recovery were also evaluated. The conventional froth flotation test with a liquid form of kerosene addition was also conducted for comparison purpose.

Jan 1, 1991

By Dale R. Andrus

Why is there such an increased thrust toward positive multiple use land management and where will it lead? History and purpose of the mining law of 1872. John Marshall discovered gold at Sutter?s mill near Coloma, California, on January 19, 1848, and utter chaos resulted. The great migration of people to the undeveloped western lands had begun. Prior to this discovery, copper, lead, and iron had been the minerals for which the laws were made. With this discovery of gold on the public domain, it became apparent that congressional legislation was necessary. This became even more apparent as each of the numerous mining districts which were springing up in California, and elsewhere in the west adopted local miners' customs to regulate their activities. Although these early miners acted under mining district rules and in some cases state regulations, they were, in reality, appropriating minerals without sanction of federal law.

Jan 1, 1970

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By R. R. Fernández

The Newmont roasting plant in Carlin, Nevada, commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable affecting the structural characteristics of the calcine, which in turn affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature has been closely monitored since October 2000. The original design temperature was 550° C. Lower roaster temperatures of around 500° C resulted in a gold recovery increase of more than six percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an ?intelligent? process control system helped significantly in achieving steady low roasting temperatures, thus obtaining high gold recoveries of 92 to 93 percent. Under these conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease in gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g., porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2010

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982