Search Documents

By Jose M. Milian, Raphael F. Matson

An intensive study was started in 1968 to determine the most economical process for winning nickel and cobalt from an extensive de- posit of complex, low grade nickel-cobalt ore (1.6% Ni, 0.10% CO) designated "the Greenvale ore." In 1974 the commercial plant at Yabulu, in Queensland, Australia, began processing the ore. In the interim, a great deal of laboratory and pilot-plant effort was applied to develop technical, process and commercial design data to demonstrate to potential financial backers and customers that a full-scale plant was feasible. The laboratory test work, pilot plant facilities and pro- gram are briefly reviewed in this paper.

Jan 1, 1979

By Priscilla P. Nelson, Yousof Abd Al-Jalil, Christopher Laughton

Prediction of excavation rates is a critical element in the pre-planning of a tunnel boring machine (TBM) project. A realistic evaluation of performance expectations is needed that reflects both the knowns and unknowns of the excavation process and geologic conditions. Current planning procedures are often based on deterministic “best guess” estimations. In this paper, a probabilistic approach to performance simulation is presented that will permit rational consideration of general and project-specific uncertainties in establishing realistic performance estimates. Companion to the simulation software is a database of over 600 public-domain case histories.

Jan 1, 1999

By Ralph Bernstein

The processing of earth observation sensor data by digital technology is almost two decades old. Only recently, however, has this technology become practical and economical. The reasons for this are interesting to analyze, and they provide some insight into what the future may bring. Some of the earlier activities and their limitations, current systems and their applications, and future technology direction are summarized.

Jan 1, 1979

By K. Hansson, A. Jedborn

Background In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore, from a system's point of view, slurry transporta¬tion would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alterna¬tive examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasi¬biliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. l . The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then tempo¬rarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situ¬ations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe¬line, and personnel are needed. In a first phase (Fig. 2), a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1989

By G. X. Wang, J. O. Marsden, M. C. Fuerstenau

Zinc cementation of high-temperature carbon eluates is now used extensively in gold processing to replace electrowinning. Under these conditions, zinc consumption is high. In this paper, zinc solubility is press rated us functions of temperature, cyanide concentration and pH in the presence of gold, silver and mercury cyanides (both individually and in combined solutions). Based on the experimental results, cementation of these metals is characterized and discussed. The importance of cyanide concentration in cementation efficiency and the effect of mercury and its co-precipitation onto zinc are also discussed.

Jan 1, 1997

By Tugba Kami?oglu

Hydromagnesite (Mg5(CO3).(OH)2.4H20), one of the sedimentary deposits in Salda Lake Basin, is developed under the control of active tectonics regime. Since the occurrence and deposition mechanism of hydromagnesite are unstable under atmospheric conditions, in order to evaluate the precipitation process, systematic host rock, lake water (surface, 20m, 40m, 60m) and hydromagnesite sampling were carried out. Macro, micro, XRD and chemical investigations were done in detail. Not only the results and formation and crystallization mechanism but also hydromagnesite's St values were evaluated. Main resources could be ultramaficmafic surrounding rocks for hydromagnesite formations. However, hydromagnesite development is considered in different phases, because it has showed various characteristics in Kayadibi and Köpekcayin areas. In Kayadibi area Huntide-Dolomite-Aragonite-Hydromagnesite paragenesis has been realized. Hydromagnesite has also formed in Köpekcayiri area, large amount of hyrdomagnesite occurrences and levels various are noticeable. Actual position of hydromagresite levels exhibits tectonic influences in and around the lake. Therefore, the levels seems to exhibit secondary formation properties. In addition, the formations are being still maintained sedimentation as products of a peripheral deposition phases. Resolving and redifferentiation sedimentation processes probably improve in periods of lake water chemistry especially Ca/Mg proportional changes, and also SI variations indicate the mentioned precipitation mechanism. Similarly, side and into the lake hydromagnesite is stored different levels and ultramafics-mafics rocks fallow indicated stages. It is postulated that hydromagnesite formation, which is existed by result of determined developments and multiphase sedimentation, could be originated from probable crack zones on the lake bottom.

Jan 1, 2005

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

By A. W. Laughlin

Analytical costs are a major part of exploration programs in developing nations which may lack adequate laboratories. Laser-Induced Breakdown Spectroscopy (LIBS), a variant of atomic emission spectroscopy, can reduce exploration analytical costs and can provide the analytical results in <1 minute. CPI is now marketing battery-powered, backpack mounted analyzers, using LIBS to analyze for many elements of interest to the explorationist. LIBS is well suited to the analysis of elements in industrial minerals. Limits of detection in ppm for some of these are: Li-1, Be-2, Na-100, B-33, Sr-10, Ba-300, Cs-1, K-500, Fe-500, Mg-500, and Ti-500.

Jan 1, 1999

By K. K. Bhattacharyya

In the Gulf Coast area lignite deposits occur in Texas, Louisiana, Arkansas, Mississippi and Alabama. Lignite has been mined in Texas since the early 1800&apos;s reaching a production of over 900,000 metric tons (1 million short tons) in 1910. With the availability of inexpensive oil and gas, production fall to as low as 16,000 metric tons (18,000 short tons) by 1950 (Henry, 1976). With the advent of the oil and gas shortage in early 1970, lignite production began to increase again. The purpose of this paper is to discuss the geotechnical considerations of mining lignite in the Gulf Coast area, particularly Texas and Louisiana. Lignite deposition occurs in unconsolidated sand, silt and clay environments. Extensive sand units saturated with water may be present within the potential mining depths. This paper describes the geotechnical considerations for designing a surface mine in this geographical area. These factors include geology, hydrology, mining method, and equipment utilization.

Jan 1, 1982

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system&apos;s point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By Dae S. Young, Eleonora Widzyk-Capehart

A quantitative estimation of the size distribution of rock fragments is extremely important in mining, metallurgy and other geotechnical fields. This paper presents a new approach to the analysis of fragmentation. The method combines the practicality of digital image processing of the rock surface with the theoretical volume calculations based on the principles and laws of fractal geometry. The final volumetric distribution curve is compared with the results from traditional sieving indicating close agreement.

Jan 1, 1996

By W. C. Bagby

The Dee disseminated gold deposit is the northernmost mine in the Carlin gold belt. We analyzed soil samples £ran undisturbed areas overlying the deposit to determine the usefulness of soil geochemistry in identifying ore zones. The depth of sampling ranged from 12 to 14 inches, depending on soil development. The -80 mesh fraction was analyzed by atomic absorption for Au, As, Sb, Hg, and T1 and by semiquantitative spectrographic analysis for Ag. Highly anomalous Au, Kg, As, Ag, and Sb are most closely associated with ore zones whereas T1 is more broadly dispersed. Hg is the only element that identifies deep ore.

Jan 1, 1984

By Sukumar Bandopadhyay

A present dominant problem is that of high downtime of the longwall shearer used in the coal production process. The means by which this problem can be overcome are many, but one of, the most important ones is that the-use of an expert system can reduce diagnostic and repair time. In this paper, a fault-diagnostic expert system model is presented. Specifically, the diagnostic architecture of the longwall shearer expert system and its use for diagnostic reasoning are discussed.

Jan 1, 1989

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By V. Nenov

The study is based on the so called METASEP process which includes selective sorption of heavy metals by special bonding agents (BA), separation of boding agents from the water by means of microfiltration and/or flotation and regenerating the loaded bonding agents, leading to a metal concentrate for reuse or discharge. The bonding abilities of different bonding agents suitable for application in METASEP process were evaluated. Two groups of BA are studied, namely: chelating ion exchange resins and water soluble oligomers. The group of ion exchange resins studied includes eight organic resins, mostly chelating cation exchangers and representatives of conventional strong and weak cation exchangers. The resins with iminodiacetic and aminomethyl phosphoric acid groups showed highest affinity towards several heavy metals. The study of resin particle size showed that this parameter is a key factor influencing the kinetics of heavy metal sorption. The group of water soluble oligomers (WSO) includes polyvinyl alcohol, carboxyl-methyl-cellulose, polyvinylethylenimin and pectin. The Metal-WSO complexes were separated by Ultra Filtration. The effect of Metal-WSO mole ratio and pH was studied. Depending on the operational conditions the heavy metal retention varies within 68-99%. It was shown that regardless of pH and mole ratio Metal-WSO, separation of certain ion from the metal mixture is not possible.

Jan 1, 2006

By Jr. Winters

The United States continues to be the largest producer and consumer of copper in the world. Table 1 on the following page shows several production statistics for 1974, the most recent year which the non-communist world copper industry might consider a good year, and for 1976 and 1977. In 1974 an estimated 24 percent of the non-communist world&apos;s newly mined copper was mined in the United States, and. 87 to 89 percent of that was from the western porphyry coppers. In 1976 U. S. new mine production was down to 22 percent of the non-communist world&apos;s newly mined copper, and the percentage of U. S. new mine production supplied by the porphyry coppers had risen to 89 to 91 percent. In 1977 the statistics remained the same as in 1976. U. S. porphyry copper production represented about 65 percent of U. S. refined copper consumption in 1974, rose to 75 percent in 1976, and dropped back to 61 percent in 1977 as imports of foreign copper into the United States began to swell.

Jan 1, 1978

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By F. C. Turin, T. L. Friend, A. G. Mayton, J. S. Jaspal, W. J. Wiehagen

This paper describes the serious injuries that have occurred to bulldozer operators working at domestic coal, metal and nonmetal mines in the United States. A serious injury is defined as one that results in either a fatality or in lost work time. Examined were 873 injury records compiled by the Mine Safety and Health Administration (MSHA). The time period covered was 1988 through 1997. These injuries resulted in 18 fatalities and 31,866 lost work days. All of these injuries occurred to dozer operators while they were performing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Jolts and jars accounted, for 604 or 70% of the serious injuries to bulldozer operators, and jolts and jars accounted for 75% of the workdays lost. Vertical jars comprised the largest set (354 incidents) of jolting and jarring injuries. In more than half of these incidents, the operator was backing up the dozer. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fallover or rollover, seven out of 17 of the operators were killed. This study finds that further reductions in injury risk would require more widespread use of seat belts; consideration (and maintenance) of the seat and seat suspension systems that might reduce injury risk from jolts and jars; research interventions to assess the effect of alternative engineering designs to dampen or isolate the effects of shock and vibration; and continued attention to skilled performance, i.e., the integration of hazard awareness, recognition and response with dozer operational skills.

Jan 1, 2003

By A. Cordonnier, Ch. Obry, R. Evrard

In spite of the large annual expenditures and the vast field of activity covered, it cannot be said that many new grinding machines have actually come to light and modified the existing market for more than half a century. Manufacturers have mainly made advances in increasing machine sizes, efficiency and reliability, and in machine automation. The relatively recent emergence of roller presses is the only exception to this homogenisation of machine ranges. The development of roller presses in pregrinding has shown the advantages of compression grinding over the ball mill from the power consumption point of view. But classical roller presses still have maintenance problems due to the high grinding pressure. The FCB Research Centre has carried out much work in this field and in particular has studied the advantages of this process in pregrinding and integral grinding. These researches lead to the development of two new compression grinding machines. The first one, HOROMILL®, presented for the first time on the 8th European symposium on comminution at Stockholm, finds its application in the field of fine to very fine grinding in dry process. The second one, RHODAX®, presented at INTERMAT in Paris, covers the field of secondary and tertiary crushing and the first stage of grinding for most of the minerals in dry or wet process. Its high reduction factor permits to do with only one machine the work realised today with two or three crushing/milling stages. These two complementary machines offer a wide range of combination summarised on [Figure 1].

Jan 1, 1995