Search Documents

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By Keith Heasley

In many practical situation where the LaModel program in used to analyze the mechanical response and failure of the mining environment, there are very few actual field measurement from the site available for deriving the appropriate input parameters. For coping with this typical lack of field data, this paper presents some recommended calibration techniques derived from on an in-depth understanding of the laminated model formulation and from many years of experience applying LaModel to practical situations. For each of the critical input parameters (rock mass stiffness, gob stiffness and coal strength) in LaModel, a specific calibration technique is recommended and presented along with the justification for the technique and some appropriate derivations/equations for assistance. It is hoped that this frank discussion of recommended calibration techniques can help novice LaModel user develop better models and can initiate a discussion among rock mechanics experts on how to improve upon the presented techniques.

Jan 1, 2008

By Ming-Gao Qian

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced normally.

Jan 1, 1992

By K. H. Brandt

A standard planning system for the development of roadways was adopted for German coal mines based on the results of geotechnical and rockmechanical investigations. Its goal is to provide for sufficient support systems under conditions of multiple seam mining at great depth. The report points out the required determination of geotechnical parameters and the basis for achieving a high level of planning reliability and resulting high performance in roadway development and longwall mining. The instrumentation and the planning procedure for selecting the support design most appropriate for the geotechnical conditions are described and demonstrated by examples.

Jan 1, 2004

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008

By Gennaro G. Marino

Documented case histories of surface ground movements from mine subsidence were utilized to help determine when the initial collapse of the overburden occurred above longwall panels. By studying this relationship between initial movement at the surface and the amount of face advance, the least-complex conditions exist for empirically assessing the span capacity of the overburden. The objective of this work was to obtain a better understanding of the overburden response to longwall mining. This knowledge will give a better insight on the long-term effects that different overburden types have on the stability and the subsidence potential of room and pillar mines, as well as, the influence of the overburden on subsidence over longwall panels. Theory on the overburden span capacity was developed and correlated to field observations. Data were used on the overburden lithology, depth, width, and face advance of the panel, and the subsidence conditions that were noted on the surface. The subsidence measured on the surface was used to determine when complete failure in the overburden rock had occurred. According to spans predicted by theory and the subsidence measured in the field, the competent lower units failed at a face advance less than when significant subsidence was observed on the surface. In each case studied, there were competent lower beds; however, the full overburden weight was not sustained to the point of subsidence. The best correlation with the surface movement was found with the most shallow, competent bed. Elastic plate solutions with various support conditions were found to best monitor the surface subsidence of these upper roof units.

Jan 1, 1988

By Xinzhi Du

Coal strength is essential to analyze the stability of excavation in coal. It is well known that the strength of coal tested in the laboratory is size-dependent, and different size specimens will produce different strength. Many researchers have studied the uniaxial compressive strength of coal and developed a number of empirical formulae to describe the strength variation with specimen size. According to a comprehensive data base that includes most of the laboratory testing results in the last century in U.S. and South Africa, the size effect and shape effect were reviewed and analyzed. The results show that different groups of coal specimens have different size effect on the compressive strength. The critical size for the size effect from the data analysis is about 40 in. The shape (W/H) of the specimens has a large effect on the compressive strength. The pillar strength formulae obtained from the data regression have a larger strength than all other existing formulae. Most pillar strength formulae have their own place in coal pillar design field. In order to analyze the difference of those formulae, twelve design formulae have been selected to compare using the Pittsburgh coal seam. The intention is not to determine the preferred formulae, but only to compare them, and see how do the W/H ratio, width, length, angle, cross-section area and effective width affect different pillar strength formulae?

Jan 1, 2008

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By Stephen Iverson

The National Institute for Occupational Safety and Health (NIOSH) is currently performing research to help mine operators minimize the amount of loose or damaged rock surrounding a blasted opening. Improperly designed blast rounds can result in excessive wall rock damage that may reduce the rock mass competency and increase ground support requirements. Unnecessary blast damage can cause many safety and operational concerns including an increased potential for injury from rock falls and other hazards resulting from sub-optimal blast designs. This paper focuses on the ground control and safety implications of blast damage in underground mines. A reduction in rock quality due to blasting can increase the amount of ground support required. Case study data collected by NIOSH in underground metal mines during standard drill and blast production rounds included blast vibration monitoring, detailed three-dimensional laser scanning of the as-built excavation, and geotechnical mapping of development headings.

Jan 1, 2007

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By Ali Naeimipour

Availability of accurate geological information about the rock mass surrounding a tunnel or mine working is the key to enhance and optimize the required ground support measures. Various approaches have been used to obtain data on ground conditions, including the possibility of characterizing the ground while drilling for roof bolts, by the Measurement While Drilling (MWD) system, via optical, sonic and acoustic televiewers, and using various types of gamma probes. While there are many different systems for characterizing the ground in longer, larger-diameter holes drilled downward, the options for using probes and logging systems in short, small-diameter holes drilled in horizontal or an upward direction are very limited. This paper will present the results of recent field tests using optical televiewer (OPTV) to analyze the joints and voids in boreholes drilled in different directions. The studies show that OPTV is a promising tool; however, getting a good quality image from the upward drill holes still need to be studied. Meanwhile, estimated in-situ strength of the intact rock is needed to complement the jointing pattern for rock mass classification. For this purpose, preliminary steps for the development of a borehole scratcher to estimate rock strength will be discussed in this paper.

Jan 1, 2014

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By John A. Rusnak

"This paper discusses the variation of coal strength based on the megascopic coal lithotypes for Central Appalachian high-volatile A coal beds. The composition of coal beds is complex and variable, depending on the depositional environment associated with original plant material, inflow of clastic material, and water level fluctuations in the original swamp/mire environment. Thus, different types of coal and sediment are formed within each coal bed. These differences in coal composition were first classified by Marie Stopes, a paleobotanist, in 1919. The classic coal megascopic lithotypes are vitrain, clarain, and durain, which correspond to bright, bright banded, and dull coal, respectively. Stopes also identified that the lithotype fusain, which is mineral charcoal, has no inherent strength and can act as a plane of discontinuity. In this study, two other coal-bed lithologies are also considered—bone and carbonaceous shale. This makes for a comprehensive suite of coal-bed stratigraphic components apart from rock partings. A total of 1,000 uniaxial compressive strength (UCS) and 440 indirect tensile strength (ITS) tests were conducted on cores from southern West Virginia that were specifically logged and described using the megascopic coal lithotype nomenclature. Statistical analysis is presented showing the results for each lithotype group with mechanical properties correlated to the lithotype. Previous studies have analyzed the mechanical breakage properties associated with coal lithotypes, which correlate well with these results. However, coal rank does appear to be a contributing factor, and this study is confined to only high-volatile A bituminous rank. Application of these results would be well suited to a rock mass classification system to address coal pillar rib stability. This would allow for rib support design and implementation to consider relative coal strength by visual observation of the seam stratigraphy through ongoing observations within a mine. Changes in seam composition can be readily identified, allowing the adjustment in rib support design. Another application would be for the determination of numerical modeling inputs based on detailed seam stratigraphy. However, these results, even with the standard strength reduction criteria, may not be applicable to currently accepted empirical coal pillar design procedures."

Jan 1, 2017

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

By Mark G. Colwell, Russell Frith

"An Analytical Model for Coal Mine Roof Reinforcement (AMCMRR) has been developed. AMCMRR utilizes a Factor of Safety (FOS) approach, which is commonly used in all forms of engineering. The starting point in the development of AMCMRR was an existing analytical roof behavior and roof support design methodology/model, originally developed by Colwell. This technique was used successfully in the Australian underground coal industry for roof support evaluation and design prior to and during the course of the research project, and when used, it was essentially calibrated on a site by site basis.It has long been recognized that bolts and longer tendons can modify the behavior and load bearing capacity of the reinforced roof via the concept of beam building. The break-through in developing AMCMRR was combining the original analytical model with a comprehensive database (associated with Australian collieries) to effectively quantify this reinforcing effect, and this in turn provided the ""platform"" by which this analytical model can be calibrated for the entire Australian underground coal industry.This paper focuses on the application and use of AMCMRR and the analyses undertaken to quantify the reinforcement beam building offers to the immediate roof. Furthermore, this paper demonstrates that a combined empirical and analytical approach is currently the most practical way of developing credible geotechnical design tools for the Australian or any other underground coal industry.BACKGROUNDBy the start of 2006 the ALTS (Analysis of Longwall Tailgate Serviceability-Colwell et al., 2003) and ADRS (Analysis and Design of Rib Support-Colwell, 2006) design methodologies were being routinely and widely used within the Australian underground coal industry. As a result of their success, Colwell Geotechnical Services commenced a research project entitled, ""The Future Development and Integration of ALTS & ADRS for Improved Underground Roadway Design. "" The project (which became known as the ALTS 2006 Project) was funded directly by several of the major coal producers as well as individual Australian collieries."

Jan 1, 2010

By Richard E. Bischke

Computer assisted finite element model analysis, originally developed to study stress distributions in aircraft, has been modified into a versatile mining program, that can be used to assist the engineer with predictions of mine subsidence. International Exploration, Inc. has developed an in-house finite element model program which incorporates a multitude of factors influencing mine subsidence such as mine design, physical rock properties, structure, faults, joints and topography. Finite element analysis of a mine model can mathematically determine the magnitude and direction of the principal stresses within each of the elements forming the model. By comparing the calculated in-situ stresses to the actual rock strengths, high risk regions within a mine can be identified. These potentially unstable regions of the mine can be allowed to fail within the model and the resultant stress redistribution and element movement calculated. Thus, the effects of the mine collapse at the surface can be predicted for the purpose of determining the potential damage, if any, that could occur to surface structures from deep mine failure. Stabilization materials can also be mathematically inserted into the model to design and analyze the effectiveness of subsidence prevention programs. Two examples are presented of the finite element program being used to predict mine subsidence at substantially different geologic and mining provinces in Pennsylvania.

Jan 1, 1984

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006