Search Documents

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By Bret E. Leisemann

The geomechanical environment in which highwall mining must operate represents a hybrid between surface and underground operations. Mine design must take into consideration the complexities associated with unsupported spans, pillars with extreme aspect ratios and the instability related to the interaction between coal extraction and the highwall stability. The rock mass adjacent to the highwall, and for a significant distance in, is affected by lateral stress relief and blast damage. This paper describes a rigorous site investigation program aimed at providing some of the input parameters for the design of highwall mining layouts at the Moura Mine and focuses upon defining the nature and extent of the relaxed zone behind the highwall. The combination of borehole imaging and C factor analysis allows delineation of blast damage and relaxation of the rock mass immediately adjacent to the highwall excavation, as well as the more subtle relaxation effects deeper into the rock mass. This has led to the formulation of a proposed geomechanical model for the relaxed zone for direct input into highwall instability analysis and mine design.

Jan 1, 1993

By Jonathan P. Furniss

The paper describes a range of laboratory tests undertaken on full column resin anchored glass fibre rockbolt systems, to assess all aspects of their performance. Laboratory instrumentation has been developed for the accurate study of strain transferral from the Glass Fibre Reinforced Plastic (GRF') bolt, through the surrounding resin annulus, and into the rock. Experience in laboratory testing to the new British Standard on glass fibre rockbolting is discussed. A critical comparison is made of the influencing parameters affecting . underground rockbolted roadway performance to the parameters assessed by BS 7861 : Part 1 The work has been co-funded by MA1 Systems UK Ltd. who supply GRP rockbolt components to the British coal mining industry, mainly for the reinforcement of coal ribsides. In rockbolting, glass fibre has a number of useful * qualities which are discussed in the paper. These properties, make the product more suitable than steel in certain applications, both in mines, and other engineering structures such as tunnels, soil stabilisation, and coastal defences.

Jan 1, 1997

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017

By Wei Wu

A new bench blast design method and its realization with the assistance of the computer is introduced. The basic design principle is to define a rhomb cell, called fully-fractured zone, through a series of full scale bench crater tests and apply this geometric pattern in multi-hole, multi-row blast design. To illustrate the design method, the optimization process and assessment of blast performance are presented in the context of a case study.

Jan 1, 1992

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016

By Kresho Galovich

Quinsam Coal Mine located in Vancouver Island, BC, Canada is mining the No. 1 coal seam at the 2 North/3 North mine and the No. 3 coal seam at 4 South Mine. This paper describes its geology and structure, mining and processing, development and depillaring practices as well as methods of roof supports under various geological conditions.

Jan 1, 2005

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By Adam Mackenzie, Dan Payne, Yass-Marie Rutty

"Historically, the Crinum mine has experienced significant falls of ground when longwall production slowed to prepare for recovery in weak roof areas. These conditions continue through the recovery process and result in both safety concerns and delays. When mine plans and exploration revealed that most of the mine's future longwall recoveries were located in weak roof areas, a decision was made to try pre-driven recovery roads as a solution to the problem. After completing eight pre-driven recovery roads with varying degrees of success and numerous lessons, the Crinum North mine now utilizes a modified Pre-driven Recovery Roadway (PDRR) to improve the longwall take-off process in weak roof areas. During mine development, a standard roadway is driven where the final recovery location of each longwall is planned. After the installation of secondary support, the PDRR is backfilled with a cement-flyash mix to provide support to the roof, and confinement to the ribs and floor of the roadway. The method has been refined over the last four years to provide greater strata stability and improved operational and safety performance compared with conventional take-offs at Crinum, and has resulted in a site record of longwall relocation in 11.5 days (pull mesh to picks in coal). This paper describes the evolution of the PDRRs from Crinum East to Crinum North, including lessons from initial attempts and changes to the secondary support regime, the operational approach during the final stages of retreat, the backfill strategy and plans for the future.INTRODUCTIONThe Crinum mine is the underground component of BHP Billiton Mitsubishi Alliance's (BMA) Gregory Crinum mine, located northeast of Emerald, Queensland (Figure 1).The Crinum mine has a history of roof control problems coming into and during longwall recoveries. Weak roof, combined with the slow mining, which is a consequence of preparing for equipment recovery, pulling mesh (which also creates tip-to-face issues), and the lengthy bolt-up process, often results in loss of immediate roof and subsequent roof falls. In fact, approximately 50% of the first 13 longwall recoveries (which were at depths of 180 to 200m) experienced roof fall delays, the longest of which took four months to mine the last pillar and recover the longwall. This recurring problem prompted the mine to investigate options to reduce or eliminate the problem."

Jan 1, 2016

By Thomas M. Barczak

The performance characteristics of Mobile Roof Supports (MRS's) were evaluated through full-scale testing in the Strategic Structures Testing Laboratory at the National Institute for Occupational Safety and Health, Pittsburgh Research Center. Safety issues pertaining to the operation and design of these supports for pillar extraction during retreat mining are examined. A unique load frame, called the mine roof simulator, provided a realistic simulation of mining conditions by inducing vertical, horizontal, and lateral loading on the support. The purpose of these experiments was to determine the capabilities and limitations of the supports and to investigate factors that influence the measurement of loading and loading rate. An evaluation of the support design and load conditions that can cause support failure or loss of support capacity are discussed relative to the laboratory tests. In general, lateral loading perpendicular to the longitudinal axis of the canopy is most severe, although horizontal loading in the direction of the long axis of the canopy can also produce critical loading in some cases. The experiments indicate that both setting force and leg pressure measurements are influenced by the staging of the leg cylinders. The implications of these factors on load rate measurement are evaluated. A comparison of MRS capacity and stiffness characteristics is made to conventional timber supports.

Jan 1, 1997

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By Bob Coutts, Matt Martin, Dan Lynch, Dan Payne

"The Broadmeadow punch longwall coal mine in Central Queensland Australia has experienced significant highwall movement associated with the effect of longwall subsidence when the longwalls approach their final position close to the open-cut highwall. In response to this movement, Broadmeadow employed two types of broadscale highwall monitoring (radar and laser scanners) to provide full coverage measurement throughout three consecutive longwalls approaching the highwall. This was to attain a better understanding of the mechanism causing the movement and potentially enable prediction of instability. Results from the monitoring found the highwall is displaced to magnitudes unlike those typically measured in open-cut mining and in direct contrast with typical longwall subsidence behaviour.This paper discusses the ground movements measured, monitoring methods used, safety measures established, as well as theorising the failure mechanism. Recommendations are made for mine and pit designs for future punch longwall layouts. The paper shows how the movements measured are more aligned to some measurements made during stream valley closure studies previously presented at the ICGCM and challenge the mechanisms suggested by previous literature.BACKGROUNDThe mining of longwalls under or adjacent to large voids (e.g., stream valleys, escarpments, or cliffs) is commonly associated with heavily vegetated or steep surface areas. In areas of extreme topographic variance, access to traditional survey pegs and stations or even new radar or laser technologies is limited. In addition, seldom have the longwall layouts aligned themselves parallel or perpendicular to the surface feature, making interpretation of any available surface movement data more complicated.The punch longwall layout (Figure 1) is also quite uncommon (only undertaken at a small number of longwall mines in Australia) but creates the perfect configuration to enable a somewhat controlled study of the effect of longwall subsidence on a steeply dipping surface feature (an un-vegetated, evenly excavated open-cut highwall). The relatively recently developed radar and laser scanning technology has also enabled near continuous, real-time, sub-millimetre monitoring of a full 500m wide x 100m high highwall. Because the punch longwall enables access and a clear view, the technology could be easily deployed as compared to the highly vegetated and variable topography of stream valleys."

Jan 1, 2018

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By Robert Kimutis, Ke Yang, Yi Luo, Jianwei Cheng

"Surface subsidence processes, especially those associated with a longwall mining operations, could cause operational and/or safety problems to railroads. For railroads with normal amounts of traffic, both the limited time window between traffic and the limited space available make the efforts to return the railroad back to its original state nearly impossible. In order to ensure the safe operation of a subsiding railway, the partial lifting method has been developed and applied. This paper describes the principle and application of the method. A case of applying this method to mitigate subsidence effects on a long section of railway has been demonstrated.INTRODUCTIONMaintaining an operational railway as it is experiencing a longwall subsidence process is not an easy task. The subsidence process may induce sufficient strain and curvature to cause problems to the railroad structures. Localized subsidence-induced slope often is significantly larger than the permissible ruling gradient of 0.7% for a locomotive to haul a loaded train reliably. In order to ensure safe operation, it would be ideal to instantly lift the railroad track back to its original level as it is subsiding. However, it is often impractical to do so due to the limited time windows available between railway traffic and the available space on the railroad base.A partial lifting method has been developed to keep the railroad operational under such limitations. The subsiding railroad track is raised by only a determined, partial amount of the occurred subsidence at a given time. By making such a determined adjustment, the railroad track can be maintained on a smooth and operational profile, and the high strain and curvature on the railroad structures can be reduced as well. To define a smooth railroad track profile in a subsided section the following two conditions should be met: (1) the maximum railroad gradient should be less than the permissible ruling gradient, and (2) the recommended amount of adjustment should be able to be made by the repair crew within the available time windows between scheduled railway traffic.The subsidence effects on a long section of railroad over two longwall panels have been successfully mitigated using the partial lifting method. The railroad experienced a maximum subsidence 89 of about 5 .0 ft (1.5 m) with the average subsidence along the entire length being about 3.45 ft (1.05 m). However, the average adjustment due to lifting that was made along the entire length of the subsidence-influenced railway was only 0.5 ft (152 mm)."

Jan 1, 2010

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By Naj Aziz

n Australia, the common method of laboratory testing of bolt for load transfer capacity determination is by short encapsulation push testing. Some concerns are raised about the validity of the test methodology, as the method does not reflect on the actual load transfer characteristics of bolt in real field situation. Thus, laboratory testes were carried out to examine the load transfer mechanisms of bolts in both the push and pull conditions. Tests were conducted by shearing a short resin encapsulated bolt out of a cylindrical steel sleeve. Three types of bolts with different surface profile configurations were tested. The study was complemented with numerical simulation of the test methods. Irrespective of bolt type the average shear load and shear stress values were found to be greater in push test, and the displacement at peak shear load was greater in pull test. The average shear stifhess values were greater in push test. The numerical simulation of the bolts provided a clear understanding of the stresses and strains generated by different bolt profiles during both the pull and pull testing process, thus allowing a better appreciation of the load transfer mechanism process.

Jan 1, 2005

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990