Search Documents

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By P. Tsang

The mechanisms and functions of yield pillar are analyzed by employing finite element method that takes time dependent and plastic failure of rock into consideration. The design criteria for different geological conditions are discussed. The results provide further evidences that yield pillar design will improve floor or roof condition, especially when the floor and/or roof strata are weaker than the coal. Based on this study, the yield pillar size is determined for one cod1 mine located in southern West Virginia.

Jan 1, 1989

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By B. Tulu, D. Gearhart

A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia. Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry. Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation, stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site. During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading, while minor changes were detected in roof deformation. As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 30–50 ft of the instrumented locations. After reaching the peak loading at about two to three inches of roof sag, the cable bolts started to unload, and the load was transferred to the standing supports. The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed. The results were used to calibrate modeled cable bolt response to field data and to validate numerical modeling procedures that have been developed to evaluate entry support systems. It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location. The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.

Jan 1, 2017

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury ? occurs during recovery operations, Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action,Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the ? interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: ? Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By P. Oliver

Rockburst conditions were first encountered at Inco's Sudbury area operations in the mid 1930's when mining advanced to below the 610 m (2000 ft.) horizon. Now, mining is being carried out at depths down to 2130 m (7000 ft.) at Inco'a Creighton Mine. While rockburst potentials have increased with depth. improvements in mine planning, methods, support systems and developments in destressing have alleviated the condition to where it is less of a problem now than it was in the early years. Hang of the improvements were developed, of necessity. through observation and reasoning because these were the only tools available at the time. Now, we are making use of stress - measurements, numerical modelling and microseismic source location technology to - help further reduce rockburat hazards.

Jan 1, 1987

By S. J. Jung

A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.

Jan 1, 1989

By Behdeen Oraee

Constructing tunnels underground is generally described as a high-risk activity because conditions in the surrounding area tend to be unpredictable. This would and can create unique dangers in every situation. It is important to gain a deep understanding of the risks associated with tunneling in order to reduce the likelihood of their occurrence and severity of their consequences should they occur. For this to be achieved, different risks should first be evaluated and ranked according to their relative importance and criticality. The Amir Kabir tunnel is considered one of the most dangerous tunnels in Tehran, Iran, in terms of the risks involved in its excavation and their potential consequences. In particular, part T4 of the tunnel passes through a zone of different strata and also a compound of various soils. This paper studies part T4 of the Amir Kabir tunnel from a risk analysis and risk management point of view. In doing so, factors increasing total cost, causing delay in the project completion time, decreasing the operation rate and downgrading project quality were identified and ranked according to their importance using the aggregate primary index risk method. For this purpose, a comprehensive questionnaire was designed and completed by tunneling experts. By responding to the questionnaires, the experts determined the relative likelihood of occurrence of the studied factors and their potential consequences. As a result, the experts suggested several alternatives to reduce the risks involved in this particular study. Moreover, the experts completed new questionnaires whilst taking into account different alternatives. In the next step, the risks before and after applying the alternatives were compared. As a result of performing the said analyses, it was concluded first that the aggregate primary index risk is an effective tool in identifying the risks involved in such projects. Second, it was concluded that, by taking into account different alternatives when analyzing and ranking the risks, severity of the said risks can potentially be reduced. Also, by considering such matters when analyzing tunneling risks, the projects? efficiency can greatly increase as a result of reducing risks that threaten financial and human resources. The approach introduced in this paper, together with the methodology described, can be adopted by the mining design engineer in all similar situations. They will be of particular advantage in such methods as room and pillar mining, where the number of similar tunnels required is high.

Jan 1, 2014

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992