Search Documents

By Gregory M. Molinda

Difficult mining conditions in deep western U.S. Iongwalls have necessitated the use of novel tailgate support systems. Extreme ground movement in these yielding gate systems has caused operators to utilize secondary support systems which match yield and strength characteristics with expected ground reaction. Other benefits include ventilation and safety gains, as well as lower costs. Recently, the use of novel support has been tried at longwall mines in other U.S. coal basins. One of the main considerations is the capability of the support to maintain an adequate airway for gob ventilation in gassy eastern coal mines. In one large Pennsylvania mine working the Pittsburgh seam, a number of support configurations were monitored over a 2,300 ft tailgate test area. The test included 4-pt wood cribs, Link-N-Lock cribs, Propsetter yieldable posts, cable trusses, and vertical cable bolts. Ground reaction, and thus support performance, was documented by roof sag and convergence instruments, ventilation measurements, and photographs. Various combinations of standing support and cable truss and vertical cable bolts provided adequate support for ventilation and safe escape. A cribless configuration consisting of only cable trusses and vertical cable bolts was inadequate to provide inby gob ventilation to the next open crosscut. Instrument ground movement data and visual documentation are presented.

Jan 1, 1997

By David Newman

The Southern Appalachian coalfield has a long history of coal bumps that are attributable to a unique combination of topography, geology, and multiple seam mining. The high pillar stresses that generate a coal bump result from: i. mountainous topography where the overburden commonly exceeds 1,500 feet beneath ridges, ii. multiple seam mining, iii. thin interburden between active and abandoned mines, iv. thick beds of competent sandstone and sandy shale strata throughout the stratigraphic section, v. strong coal seams, and vi. irregular pillar and mining geometry in older room-and¬pillar mines. Coal has been intensively mined for more than 100 years in Eastern Kentucky, Southwestern Virginia, and Southern West Virginia. As a result, it is commonplace to have abandoned mines above and/or below active operations. Therefore, those conditions that generate coal bumps will be more prevalent in the future, as underground mining continues in Southern Appalachia. The focus of this paper concerns two coal bumps that occurred in the Kellioka seam where both undermining and overmining had occurred. The purpose of the investigation is to determine the magnitude and distribution of vertical stress that initiated the bumps, to identify bump-prone areas in the unmined reserve, and to recommend pillar centers and mining layouts to avoid future bumps. The state of stress in three vertically adjacent seams was examined using the LAMODEL boundary element program. Large, detailed numerical models were constructed of both bump areas and of the remaining unmined reserve block. The results of the numerical analyses were compared with those obtained using analytical equations.

Jan 1, 2002

By Christopher Mark

The demographics and safety record of the pillar retreat segment of the U.S. coal industry was analyzed using statistics collected by the Mine Safety and Health Administration. Pillar recovery is practiced primarily by mines in Appalachia and the Midwest. Using 1993 data, the accident rates and productivity of a large sample of pillar re- mines were found to be similar to other room-and-pillar mines in the same geographic areas. Pillar recovery apparently accounts for about 10% of all U.S. underground production, but has been associated with about 25% of the mf and rib fatalities during 1989-96. However, of the 28 fatalities that were analyzed, only 4 occurred for which no citations were issued for violations of mining law. Nearly one- half of the fatal incidents occurred during the mining of the last lift or pushout. All four no-citation incidents occurred during the removal of the last lift during a "Christmas tree" extraction sequence.

Jan 1, 1997

By T. J. McMahon

This Bureau of Mines study describes the development of a large-scale, three-dimensional, finite-element model of a deep-vein Coeur d?Alene District mine. The three-dimensional model was prepared from combined digitized mine maps and generated levels that may also be analyzed as independent two-dimensional models. A comparison of the stress changes and displacements was made following a simulated vein excavation in both the three-dimensional and two-dimensional models. A one-cut excavation was simulated with the two-dimensional model and a multiple-cut excavation was simulated with the three-dimensional model. The compared results from the two analyses are discussed in terms of the inherent differences between the models.

Jan 1, 1989

By Greg Hendon

Longwall developments in the UK have historically consisted of single entry gate roads. Adjacent developments were separated from existing panels by large barrier pillars (designed of sufficient width to get away from the longwall abutments of the previous panel) or by small barriers driven in the shadow, or de-stressed zone, of the previous panel. Some 2nd panel tailgates were also driven skin to skin leaving no coal barrier between the newly driven entry and the heavily supported existing gateroad. With the developement and wide acceptance of fully bolted entries and the pressure to reduce production costs, alternatives to single entry drivage, particularly yield pillar developments, were examined. Through the Rock Mechanics Branch of British Coal, a cooperative study was begun with Jim Walter Resources, Inc., USA, (JWR) to look at the yield pillar alternative in detail. This study was to determine the feasibility of utilizing yield pillars in the UK and to determine, through monitoring, the possibility of reducing stable pillar widths at JWR. The study has included extensive monitoring of the yield-stable-yield pillar system at JWR No. 7 Mine and an underground trial of a two entry yield pillar test area at Welbeck Colliery in the UK. This paper describes results from the JWR study and the subsequent results of the first advancing yield pillar development in the UK at Welbeck Colliery.

Jan 1, 1995

By David Bartsch

The Ohio Valley Coal Company (Ohio Valley) has operated the Powhatan No. 6 Mine in Belmont County, Ohio since 1972. Ohio University owns a 455-acre research farm over a portion of the Ohio Valley reserve containing 51 acres of old-growth forest known as Dysart Woods. In 1988, when Ohio Valley applied for a new mining area for its first longwall located several miles away from Dysart Woods, Ohio University claimed that mining at that distance would lower the regional water table and kill the old trees. In response, Ohio Valley began to study potential impacts from longwall mining on hydrology, soil moisture, and tree growth. Early studies examined the impacts of longwall mining on hydrology, soil moisture, and tree growth directly over mined areas compared to woodlots that were not undermined. A subsequent study examined tree-ring growth for a five-year period before and after longwall mining for several woodlots, some directly over panels and others at distances of up to 2000 ft away. No significant differences in growth rate associated with longwall mining were observed. New research was begun that compared longwall-mining impacts on groundwater hydrology, available soil moisture, and tree growth in two stands of mature trees located near Dysart Woods in order to confirm the earlier results. Using a test technique known as "Before-and-After-Controlled-Impact-Pairs," data was collected from one woodlot (test) that was undermined and from another (control) that was not undermined. Data collection began several years prior to longwall mining and has continued for several years after mining. The data for the test site shows that although the shallow and deep groundwater levels were affected by longwall mining, the soil moisture, vigor rating, or the growth rate of trees did not decline significantly compared to the control site where there were hydrologic impacts. The study shows that there are no known significant impacts to trees from longwall mining. The results of these studies were used by Ohio Valley to obtain State approval to longwall to within 300 ft of Dysart Woods

Jan 1, 2005

By Xu Linsheng

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including modelling.

Jan 1, 1992

By Buddhima Indraratna

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks.

Jan 1, 1992

By Yanfa Gao

Clusters of underground openings were developed around the shaft bottom of Tangshan Mine. They were deep and located in soft rock strata. After development, those openings have been subjected to considerable deformation and damages. A combined supporting method including grouting and bolting, shotcrete lining and brickwork was used. This paper analyzing the theories on which this supporting method was based. A new theory called "Disturbed Creep" was developed for deformation prediction of openings surrounded by strata subjected to stresses close to limiting or failure strength. Keywords ground pressure, deep mine, soft rock, stability control

Jan 1, 2002

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks' operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

By Leslie Carver

The effects of longwall mine subsidence on water resources were studied at a West Virginia coal mine (mine Z) by Carver (1994). Data were obtained for 137 domestic supply wells and springs and 12 baseflow streams. Subsidence caused short-term dewatering (of a few days to weeks) of wells located on lower hillslopes and valleys, and long-term dewatering of hillslope and hilltop springs (with no recovery yet). New or increased spring discharge was observed at lower elevations. Unsubsided water supplies experienced no dewatering beyond a nearby panel's 27°-38° angle of dewatering influence zone. Subsidence from longwall mining beneath streams commonly reduced discharge when panel ages were less than two to three years. However, "normal" discharge was typically observed over panels greater than three years in age; such streams exhibited lower baseflow recession constants, moderated winter baseflow, and increased summer baseflow compared to unsubsided streams.

Jan 1, 1994

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By M. Ashraf Mahtab

A feature of interest in stability of excavations in domal salt is the phenomenon of gas outbursts which has occurred in five of the six mines in Louisiana salt domes. Gas outbursts are sudden erruptions of salt and gas from the face or roof of a mine opening. They are associated with anomalous zones in salt, depth of mining, and the method of excavation. Potential risks from gas outbursts include an unplanned connection to a reservoir of water or hydrocarbons and, possibly, a loss of the mine. It is proposed that a gas outburst is initiated by disking in biaxial compression and propagates by spalling of the cavity walls and further disking. The outburst is terminated by a combination of dilatancy hardening, increase in stress along the cavity axis, and enlargement of the cavity to the boundaries of the pressure pocket. Identification of burst- prone areas will require research into in situ measurement of material characteristics and further under- standing of the mechanism of gas outbursts. Shock blasting in advance of mining appears to be a promising technique for controlling gas outbursts.

Jan 1, 1981

By Dion Pastars

Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective, the system requires the mixing of the catalyst and mastic components of the resin, as well as shredding of the laminate cartridge that contains the resin. An unknown measure is the load transfer characteristics of a bolt where the resin is well mixed but remains encased in the cartridge (gloved). Laboratory and in situ field investigations have been undertaken to quantify the performance loss due to mixed gloved bolts. This work showed repeatable results, indicating serious performance loss of the gloved and mixed system, with load transfer approximately 10- 15% of a non-gloved system (MacGregor, 2004). The in situ testing has demonstrated the relationship between the adhesion qualities of the resin and the mechanical interlock generated by radial confinement with progressively increasing tensile load. Effective load transfer is defined by the ability of the system to sustain shear stress on the bolt hole wall.

Jan 1, 2005

By Syd Peng

In designing a proper roof support system, one must know the features of roof geology in advance of mining. The drilling parameters obtained during normal roof bolt installation cycle can provide a large amount of information on the roof geology when properly interpreted. It is also an economic way for identifying the geological features of the roof. This research develops a method for predicting the roof geology based on the drilling parameters obtained during roof bolting operation. From the results of a series of laboratory and underground tests, feed pressure is found to be a good indicator for identifying the voids/fractures and estimating the roof rock strength. This paper describes the method for determining quantitatively the location and the size of void/fracture and estimating the roof rock strength from the drilling parameters of roof bolter.

Jan 1, 2005

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By W. G. Pariseau

A new approach to the direct inclusion of the effects of joints and geologic structure in rock mechanics analyses is applied to an elastic analysis of stability of a Lucky Friday undercut and 4111 longwall stope (WL) using the finite element method (FW). The approach is base+ on the concept of equivalent properties of a heterogeneous test volume, but does not depend on the assumption that a test volume is a representative volume element. Comparison with conventional FW results show greater variability in fields of stress, strain, displacement, safety factor and energy densities. Stability requires a knowledge of rock mass strengths as well as elastic moduli.

Jan 1, 1989

By Jim Sandford

The South Bulga Colliery longwall operation, owned and operated by Cyprus Coal Australia. Oakbridge Pty. Ltd., and located near Singleton, NSW, is currently operating under an average 80-ft-thick (24-nt) sandstone unit residing immediately above the coal seam, resulting in sudden and severe face weightings. To date, nine severe weightings have occurred at the property (within Panels 3, 4. and 5), three of which resulted in face closures accompanied by significant equipment damage and several weeks of downtime. The remaining six events nearly resulted in face closures, incurring single-pass vertical convergence of up to 8 in (200 mm) along the pan line. In an effort to mitigate and/or eliminate the occurrence of these severe weighting events, mine management has established an in-house program to immediately address the geotechnical and operational mechanisms underlying rapid weightings, as well as specific measures to mitigate these events on future panels. In support of this in-house effort. NSA Engineering Pty. Ltd., is assisting the engineering staff at South Bulga in developing a more aggressive face monitoring program. The aim of this program is to provide weighting occurrence predictions sufficiently ahead of time to ensure that operational controls are optimized prior to attempting to mine through potential weighting areas. This paper reviews the occurrence of weightings to date at the South Bulga Colliery as well as the latest developments in shield monitoring technologies to forecast these events in near-real time.

Jan 1, 1999