Search Documents

By N. C. Saxena

Subsidence investigations in Indian coalfields have led to development of relationships between subsidence movement parameters and defining of safe limits of subsidence movements for surface properties. The maximum subsidence over caved workings was generally not more than 60% of extraction thickness underground while in case of hydraulically sand stowed workings it was generally not more than 5%. The relationships have been useful in extraction of more than 7-million tonne of coal from underneath and in the vicinity of surface properties.

Jan 1, 1988

By Dennis R. Dolinar

The U.S. Bureau of Mines has modeled yield pillars to determine the effects of reinforcement techniques on pillar performance. Model pillars with width-to-height (w/h) ratios ranging from one to four were reinforced using advanced lateral support systems. To evaluate reinforcement and pillar performance, the model pillars were strained up to 18.6 pct in compression. The results show that the reinforcement had a significant effect on the postfailure characteristics of the pillar but had only a small effect on it's maximum failure strength. Pillar residual strengths increased up to 10 times, while the energy capacity increased by a factor of three depending on the reinforcement method. At maximum deformation, the residual strengths of several types of reinforced specimens exceeded the maximum compressive strength up to 2.5 times and resulted in an increasing positive postfailure stiffness. Test results, data analysis, and application of the results to underground mining are discussed.

Jan 1, 1993

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By S. M. Matthews

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ monitoring of behaviour has been carried out to confirm the mechanisms involved.

Jan 1, 1992

By Khaled Morsy

This study presents a typical stress-strain model for coal material using the available in-situ and laboratory tests data conducted on coal. This model can be used as a basic coal model in finite element applications The effects of pillar width-to-height ratio and the confining pressure have been considered in this model. The extended Drucker-Prager model with mobilized friction angle was found to be very successful in simulating the proposed model.

Jan 1, 2001

By C. W. Bollier

In recent years, Peabody Coal Company has enjoyed a great amount of success using roof trussing as a secondary support system. Since 1975, over 180,000 trusses have been installed in 12 different Peabody mines with varying geological conditions. Projections from Peabody, and throughout the mining industry, indicate a continuous growth in the trussing principle for roof control. Peabody's primary supplier has sold over 1,000,000 trusses to 50 different mines throughout the country. (1) Roof trusses provide an improved means of controlling difficult roof conditions which, in turn, improves worker safety and mine production. Since the original development of the truss, (2) the only major modification to the trussing procedure has been the addition of the resin point anchor system in the mid-70's. The resin point anchor was the catalyst needed to provide a reliable anchor and create acceptance of the roof truss by both management and labor. Peabody began using trusses in their mines in 1975. For the first few years, most of the truss effort was geared toward determining proper anchorage, spacing, and gathering historical data. In recent years, Peabody's activities have centered on the development of improving trussing procedures. Through monitoring and trussing activities, a number of areas of improvement have been found.

Jan 1, 1982

By Anthony T. Iannachione

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures. Microseismic activity associated with these roof falls occurs in distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fall can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

Jan 1, 2001

By Larry Stolarczyk

The mining industry would benefit greatly by imaging geologic conditions well in advance of mining. In layered deposits such as coal, trona, quartz, and potash, natural waveguides form and enable electromagnetic seam waves to travel great distances. In the early 1980s, the Radio Imaging Method (RIM) was developed to capitalize on electromagnetic seam wave propagation in the assessments of seam conditions in longwall panels. The initial applications of RIM tomography and comparisons to in-mine mapping of geologic conditions proved that faults, paleochannels, and rapidly thinning coal could be detected and imaged with seam waves. This paper describes the application of electromagnetic seam waves in mapping the margins of a paleochannel crossing a longwall panel and the interesting possibility of adopting the newly developed Full Wave Inversion Code (FWIC) )Newman 1995) to significantly improve imaging resolution. When tomography images are combined with ground control science, a significant reduction in cost, roof fall potential, and waste rock in underground mining may be realized.

Jan 1, 1999

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By James G. Schotsch

Unmapped abandoned mines are hazards for under¬ground mines, surface mines and surface structures. The Radio Imaging Method (RIM) provides a cross borehole technique to remotely detect abandoned mine works. RIM was used at the Buck Creek Mine, an underground coal mine, to determine the extent of unmapped mine works. The information provided by the RIM survey assisted the mine planners in developing their mine.

Jan 1, 1990

By M. Terry Hoch

This paper presents information on low-coal ATRS systems that are now in use. A study was conducted consisting of an in-mine evaluation of ATRS- equipped roof bolters capable of bolting in seams below 42 inches. Machine manufacturers, MSHA personnel, and bolter operators were asked to assist in reviewing the operation of various low- coal ATRS systems. Features of each system are outlined and operational problems and limitations of each are analyzed. Specific applications, such as ATRS-equipped bolters designed for use with auger-type miners, are also examined.

Jan 1, 1988

By Kikro Matsui

Longwall mining 1s more productive in comparison to other methods but requires particular conditions for its effective use This paper relates to longwall roof instability at Ikeshima Colliery In order to make clear the cause of the longwall roof instability, scientific investigation in terms of geomechanical factors and longwall support system was planned and carried out

Jan 1, 1997

By Marek J. Mrugala

Coal strength based on scaled uniaxial compressive strength from the laboratory and back calculations from in-mine observations of pillar stability indicate that material strength scaling rules are open to debate. Analyses presented indicate that the application of scaling factors lower than 0.5 provide a better correlation with field observations of pillar stability.

Jan 1, 1989

In this paper, the plastic increment theory was applied in a 2-D finite element model, and a generalized Von Mises yielding criterion adopted to simulate the progressive failure of coal pillars. Extensive underground monitoring was conducted and the data compared with the computer model, yielding promising results. Three different longwall entry layouts, including a stable (s-s) pillar system, a yield-stable-yield (y-s-y) pillar system and a yield (y-y) pillar system, were investigated using the model developed. The yield-stable-yield system was considered to be the best of the designs studied in the case. A comprehensive parametric analysis was also performed. The triaxial factor and Poisson's ratio were found to be the most important material parameters affecting pillar yielding.

Jan 1, 1988

By John W. Fredland

Conducting mining operations under a body of Water can create hazardous conditions for miners. The potential for a sudden inrush must be considered and abnormal ground control conditions can be encountered. This paper synopsizes the factors which mine operators should take into account when evaluating whether an inrush may occur. It addresses the applicable Federal regulations and discusses some items which coal operators should consider in applying for a permit, Through collecting and analyzing the pertinent information, the likelihood of encountering problems can be judged. Through proper mine planning, the potential for creating hazardous conditions can be mitigated.

Jan 1, 1982

By John C. Stankus

At the 19th International Conference on Ground Control in Mining, a paper was presented detailing new types of Jennmar INSTáL tensionable cable bolts (Stankus and Taylor, 2000). Since that time, significant testing and trials of the various types of tensionable cable bolts have been conducted. Several MSHA districts and state regulatory agencies have now approved these systems as primary support This paper will detail the use of tensionable cable bolts as primary support at two longwall mines in Virginia (MSHA District 5).

Jan 1, 2001

By Michael Alber

Coal resource extraction reaches higher depth of overburden and rockbursts as well as associated seismic events appear to become an additional problem to he addressed by ground control engineers. For example, German coal mines approach a depth of overburden of some 1400 m (4200 ft). Certain strata at those depths and associated high stresses may react upon resource extraction and subsequent deformation by violent release of strain energy, termed rodcbursts. Rock mechanics tests on numerous rock types have been conducted and three types of brittle rock behavior were classified. This paper describes different types of rock behavior in uniaxial compression and discusses a possible classification of rock with respect to their likelihood of violent response upon loading.

Jan 1, 2004

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001