Search Documents

By Seung-Chul Lee

Transparent conducting tin(1V) oxide thin films have been studies and developed for the electrode materials of solar cell substrate. Fabrication of tin oxide thin films by sol-gel method is process development of lower cost photovoltaic solar cell system. The research is focused on the establishment of process condition and development of precursor. The precursor solution was made of tin isopropoxide dissolved in isopropyl alcohol. The hydrolysis rate was controlled by addition of triethanolamine. Dip and spin coating technique were applied to coat tin oxide on borosilicate glass. The resistivity of the thin film was lower than 0.18-cm and the transmittance is higher than 90% in a visible range.

Jan 1, 1999

By L. Klinger, T. Werber, LA Levin, A Katsman

"The process of catastrophic carburization known as ""metal dusting"", whereby a solid metallic material is converted into fine particles in a carburizing atmosphere, was analyzed. It was shown that this conversion is the result of plastic deformation and subsequent fracture accompanying diffusional phase formation in the near-surface layer. The process is controlled by internal stresses arising during phase transformation. Competition between stress generation and relaxation may result in the attaining the ultimate strength in the near-surface layer and its fracture. Such a mechanism of metal disintegration may occur in a certain temperature interval depending on the kinetic and geometrical parameters of the system - the diffusivities of the alloy's components, the ratio between specific volumes of the new and the old phases, and the ultimate plastic strain. The temperature interval for disintegration of carbon steel, the rate of disintegration, and the period of the disintegration cycle, were evaluated and compared with experimental data. IntroductionCatastrophic carburization, known as ""metal dusting"", consists in conversion of a solid metallic material into fine particles. The process occurs in a carburizing atmosphere at elevated temperatures. The corrosion product, usually named ""coke"", consists of metallic particles dispersed in a loose carbon matrix. Under industrial conditions metal dusting takes place, for example, in a gas mixture of CO and H2 or in hydrocarbon environments. Steels, nickel- and cobalt alloys are susceptible to this kind of wastage in the temperature range 400-800°.A mechanism of metal dusting in steels was proposed by Hochman [1] and later developed by Grabke and coworkers [2-5]. According to the proposed model, the process consists of the following reaction steps:"

Jan 1, 1996

By D. J. Brennan

A techno-economic study is in progress, examining process and product options for treating smelter gases containing various concentrations of sulphur dioxide. Key contenders have been examined within an Australian context using the following criteria: * Markets for products * Capital Costs * Operating Costs * Waste streams generated Product options considered thus far are sulphuric acid, sulphur, calcium sulphite and gypsum. The development of an appropriate overall framework for evaluating process and product options is discussed and findings thus far presented. The emerging techno-economic study offers promise as a constructive guide to future policy decisions by industry and government.

Jan 1, 1994

By Feng Chen, Lirong Chen, Yufeng Guo, Wenjie Weng, Tao Jiang

"In this paper, the carbonthermal reduction behavior and the influencing factors of Panzhihua ilmenite under the condition of carbon-burdened were systematically investigated. The results show that the ilmenite forms into titanium nitride during the reduction process at 1200 °C under the condition of carbon-burdened. Carbon-burdened is beneficial to the reduction of iron oxide, but less favorable for the growth of iron grain.IntroductionThe titanium ferrous resources are very rich in Panzhihua-xichang area, accounting for about 38.85% of the world's proved reserves [1]. However, TiO2 grade of this kind of ilmenite is low and calcium magnesium content is high, it generally requires preconcentration to titanium-rich material—titanium slag or synthetic rutile.Chlorination process is an advanced method for production of titanium dioxide, which should takes high quality titanium-rich material with low content of calcium and magnesium as raw materials (the content of MgO and CaO are less than 1.0%). Ilmenite in Panxi area, however, contains high calcium and magnesium; it is not suitable as a raw material for chloride process. Methods of producing titanium-rich materials which have been applied in industry are electric smelting, various acid leaching and reduction rust [2-5]. There still exist some problems such as CaO and MgO removed not thoroughly, low resource utilization, high energy consumption and environmental pollution."

Jan 1, 2012

By Juergen Antrekowitsch, Stephan R. Steinacker

The main aim of the electric furnace treatment in the primary copper industry is the reduction of valuable metals such as zinc, lead or copper itself. On the one hand legal restrictions for the further use of the treated slag are constantly getting stricter while on the other every type of loss in the oxidic phase leads to economic disadvantages. In order to fully understand and to improve the process, kinetics during the reduction play an essential role. In the first part, this paper highlights the theoretical background of the reduction process, while the following chapters present experimental aspects and results from laboratory scale trials at the Montanuniversitaet Leoben. In addition, the comparison between the chemical reaction and the diffusion model plays a continuously important role. By investigating the reducibility of electric furnace slag, process adaptions and ameliorations are developed.

Jan 1, 2016

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Yutaka Saito

"Effect of moisture content must be fully understood for controlling the granule compaction of ceramics. It changes the mechanical behavior of spray-dried granules applied for compaction process, and governs the structure and properties of .ceramics. To understand the time-dependent change in processing, the kinetics was examined for change of moisture content for granules placed in a die and the pressed compacts also. The results were explained in terms of apparent moisture diffusion coefficients. They varied non-linearly with the PVA content in the granules. The results were explained through the non-uniform PVA distribution in the granules.IntroductionMoisture must be controlled in compaction process to produce the green compacts having uniform structure. It affects glass transition temperature of binder and thus the deformation behavior of powder granules under an applied stress. Several studies [1-7] have clarified the effect of moisture content on the compaction behavior of granules and the structure of resultant compacts for both die pressing and cold isostatic pressing (CIP) of pre-formed compacts. In these studies, the moisture contents in the system were equilibrated with the humidity in the atmosphere before compaction. In practice, however, the moisture content in the system may vary with time if the relative humidity of surrounding atmosphere is different from what the granules were equilibrated previously. This is very likely case in real production processes. However, the kinetics of moisture change in the granules as well as in the pre-formed powder compacts have not been well studied. For controlling the microstructure in a system, it is necessary to fully understand the kinetics of moisture change and its relevance to packing structure of powders."

Jan 1, 2000

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Viscosities of FeO-SiO2-V2O3-CaO-P2O5 slags have been measured at the temperature range of 1673 K to 1773 K (1400°C to 1500°C). This investigated system represents the major components of basic vanadium slag that is an important intermediate product of a novel vanadium extracting process, in which removal of phosphorus and extraction of vanadium can be achieved from the vanadium-containing hot metal simultaneously. It was found that higher CaO/SiO2 ratio resulted in lower viscosity in the composition range of interest. Also, the viscosities increase with the increasing P2O5 concentration. The varying viscosities can be attributed to the modification in complexity and polymerization of the slag network. The variation of apparent activation energies are in tune with the viscosity measurements. The results of this work revealed the effect of CaO/SiO2 and P2O5 on the viscous properties of FeO-SiO2- V2O3-CaO-P2O5 slags and therefore provide the theoretical foundation for the control of the coupling de-P and V-extraction process.

Jan 1, 2016

By Qingbo Yu, Qin Qin, Junxiang Liu

"Dry-granulation is a new process of molten blast furnace slag treatment and air is used as heat exchange medium. There are some shortages: poor effectiveness of granulation, high air-slag ratio and high energy consumption, which are the obstacles to popularize dry-granulation. Based on rotary cup atomization, the technique of recovering waste heat of molten blast furnace slag through waste heat boiler producing high pressure steam is exploited. The molten blast furnace slag is granulated to uniform small slag granules with high temperature, and slag granules pour into the waste heat boiler. It could produce steam, obtained in first row and second row tubes, when descending velocity of slag granules equaled 1.1mm/s and the Reynolds number equaled 7100. The application of the system for recovering waste heat from high temperature molten blast furnace slag has a significant meaning.IntroductionBlast furnace slag is one kind of solid waste in iron making process, which is discharged at the temperature range from 1723 to 1923K. In China, there was 0.162 billion tons of slag discharged in 2009, and the energy contained in the slag is equivalent to the energy in 9.4 million tons of coal equivalent. The sensible heat of molten slag is a very valuable waste heat source, so it is worthwhile to recover the sensible heat. At present, the molten slag is treated by a water quenching method. But in this process, the sensible heat is not recovered, moreover, an amount of water is consumed and harmful waste gas is discharged into the environment. Due to the considerations of energy conversation and environmental protection, the iron making industry pays close attention to dry-granulation, which is useful to obtain more benefits [1-4]. The sensible heat is recovered and an amount of water is saved by the method of dry-granulation. The amorphous content of slag granules obtained from dry-granulation is over 95% [5, 6], so the slag granules can be used as a perfect raw material for cement [7, 8].In the late 1970s, the Sumitomo Metal Industries, Ltd. and the Ishikawajima-Harima Heavy Industries, Ltd. jointly undertook the research of rotary drum granulation. This method has several disadvantages: the processing capacity and efficiency are low, and it is not adoptive to operate continuously in production [9]. From 1980, Nippon Steel, NKK, Kawasaki Steel, Kobe Steel, Sumitomo Metal Industries and Nisshin Steel were engaged on air granulation, and the experiments were operated for 6 years on the blast furnace in Nippon Steel. In the process of air granulation, there was great power consumption. The complexity of structure and the great floor space of the air granulation device caused high cost of investment. In 1986, Ukraine exploited a new method of heat recovery referring to the technology of Continuous Casting and Rolling [10]."

Jan 1, 2011

By Kenji Monden

"The creep properties of tin-based lead-free solders Sn3.0AgO.5Cu and SnO.7CuO.1Ni and lead solders 10Sn90Pb and 50Sn50Pb were investigated at temperatures between 298 K and 398 K. The creep-rupture time decreases with increasing initial stress and temperature. The analysis of the solder creep curves uses the Omega method. The creep rate E is expressed by following formula: 1n ? = 1n ?0 + O?, where ?0 and O are experimentally determined. The parameter Eo increases with increasing initial stress and temperature. The activation energy for ?0 is 108 kJ/mol for Sn3.0Ag0.5Cu and 85 kJ/mol for SnO.7CuO.INi. These energies suggest that the lattice diffusion of tin is dominant. The energy of 1OSn90Pb is 37 kJ/mol and that of 50Sn50Pb is 67 kJ/mol. The creep-rupture time is calculated using the parameters, ?0 and O. The calculated creep-rupture time is in good agreement with the measured creep-rupture time.IntroductionLead-free solders are replacing traditional tin-lead solders as part of a major trend toward protecting the earth's environment. However, tin-lead solders are currently needed for a high temperature range. Since creep is the main deformation mechanism in solder joints, understanding a constitutive model for creep and examining creep data for solders are important for reliability analysis of solder joints. A steady-state creep equation is generally used for solders [1,2], and it supposes that the secondary-, or minimum-, creep rate occupies the entire creep life. However, secondary creep accounts for only about 15 % to 40 % of the entire creep life for solders. Thus, the equation may not represent the entire creep life."

Jan 1, 2012

By Chenhui Liu, Ka-ma Huang, Hong-ying Xia, Bingguo Liu, Hua Chen, Jinhui Peng, Libo Zhang

"The rising popularity of microwave heating in mineral processing has fuelled the need for knowledge concerning dielectric properties of minerals. Dielectric property and microwave absorption property of anthracite were measured over a temperature range of 20-100°C at 2.45GHz by using an open-ended coaxial sensor measurement system. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of anthracite are highly dependent on temperature and frequency. At frequency of 2.45GHz frequency used in microwave metallurgy, anthracite is suitable for reducing agent to achieve fast elevation of temperature then returning to original state. The research will be helpful in explaining the thermal running of microwave dielectric heating the anthracite.IntroductionThe application of microwave heating in minerals processing and treatment has recently attracted great interest from the metallurgical industry. Compared with conventional heating methods, the advantages of microwave heating include rapid and selective heating, uniform distribution, high efficiency, fast on and off switching as well as flexible and modular design[l-3]. As a result of these advantages, microwave heating has been applied in a variety of mineral processing and extractive metallurgy, such as microwave-assisted ore grinding, microwave heating for carbothermic reduction and acid leaching of ilmenite ore, microwave drying, microwave-assisted roasting and smelting of sulfide concentrate, microwave-assisted spent carbon regeneration and microwave-assisted waste management [ 4-6]. Though the application of microwave heating in the metallurgical industry is promising, further studies on the interaction between microwave radiation and minerals and its effects are highly desired to develop innovative techniques for minerals processing and ore treatment using microwave heating [7]."

Jan 1, 2013

By M. I. Kalashnikova

The leaching of metal nickel in copper sulfate solutions is investigated. It is established, that irre-spective of presence or absence of chloride-ion and oxidizer (oxygen) in system process can be divided into three stages, characterizing by restoration and oxidation of metals with formation of metal copper and cuprite and differing in the speeds of sedimentation of copper and transition of nickel into solution. At the initial stage of process along with allocation of metal copper it is be-sieged cuprite, that results in excess of speed of sedimentation of copper in comparison with dis-solution of nickel. At the second stage speed of transition of nickel into solution falls practically to zero, and sedimentation of copper proceeds on reaction of interaction of metal copper with copper sulfate solutions with cuprite formation. During the final period speed of transition of nickel into solution exceeds speed of sedimentation of copper due to course of reaction of resto-ration of cuprite up to metal. Influence of an ion of chloride and oxidizer on formation of various phases is revealed. It is established, that presence of an oxidizer results in increase in a share of cuprite in a deposit. With increase of the maintenance of chloride-ion speed of metal copper allo-cation essentially grows even at presence of an oxidizer in system.

Jan 1, 2006

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

Copper and gangue mineralogy constitute the most critical parameters for the hydrometallurgical processing and cost-efficient extraction of copper. Minor changes in copper-, rock-, or alteration mineralogy can severely impact the comminution efficiency, curing, agglomeration, acid consumption, copper extraction and PLS impurity loading. Further, copper leach operations, particularly in the southwestern United States, are increasingly challenged by a combination of low grades and semi-refractory copper. This paper discusses the metallurgical and economical benefits of continuous mineralogical analyses in order to establish and operate a mineralogical data base in copper leach operations. Troubleshooting for copper extraction, integration of process mineralogy into production forecasting, and process optimization will be illustrated with operational experiences from Chile and the United States.

Jan 1, 1999

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012

By Carlos A. Ferreira, Betina Hansen, Marco A. S. Rodrigues, Marcela P. Proença

"Nowadays, the concern with the reduction of industrial pollution has motivated researchers to found out new technologies for treatment of industrial waste. The clean technologies, as electrodialysis, are capable of treating these residues, minimizing the impacts when they are discarded directly on the environment. Membranes of SPS/HIPS, PAniCSA/SPS/HIPS, SPAN/SPS/HIPS were developed using chemical mixture method. Membranes were characterized by Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA) and Scanning Electronic Microscopy (SEM). Membranes were submitted to electrical polarization and to electrodialysis at NaCl and KCl solutions, in order to determine ionic transport through the membranes. Results were compared with commercial membranes. The average percent extraction for Na+ ions obtained by membrane was beyond 20%.IntroductionThe high environmental impact caused by the galvanoplastic industries represents today a world concern(1). In the galvanoplasty, thin metallic layers are deposited on metallic surfaces(2) through chemical methods or electrochemical process. This industrial process presents some disadvantages that limit its utilization, as the generation of toxic effluents containing concentrations of heavy metals usually above the limits allowed for his release in receiving bodies(1), the production of galvanic sludge which is considered hazardous waste and that is very difficult to treat, beyond the high consumption of water (3).Stimulated by the development of new ion-exchanged membranes with high selectivity, lower electrical resistance, and improved thermal, chemical and mechanical properties, the use of electrodialysis in the wastewater treatment has recently gained a broader interest(5). The electrodialysis (ED) is a mass separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution(5). The technique permits the recovery and the reutilization of the waste products from the industrial process, avoiding the discharge of them on the environmental (acting as clean technology)."

Jan 1, 2008

By Yuri Gelfgat

"This paper presents some results of the investigation of the steady magnetic field influence on hydrodynamics and heat/mass transfer in processes of semiconductor single crystal growth (Si, Ge, InSn). The investigation employed mathematical and physical simulation techniques of relevant processes and full-scale experiments on growth facilities. A number of additional MHD phenomena have been found generated in the melt due to the rearrangement of flow pattern, the formation of specific convective cells, and the origin of MHD boundary and shift layer.IntroductionMagnetohydrodynamic (MHD) means of creating forces by contact-free methods in liquid conducting media have been widely used in the production of volume semiconducting single crystals. The goal of this method is to control convective transfer processes in the melt volume and on the crystallization front [1-3]. This is due to the sufficiently high conductivity of semiconductor melts (s = 104 /106 O1m-1 ) and an obvious relationship between the hydrodynamics in the melt and at interfaces and the conditions of formation of single crystals and their quality [ 1].All types of MHD effects rest upon the generation of volume electromagnetic forces in the melt by various means as well as on the possibility to direct them arbitrary in space and to adjust easily their absolute values. Fig. l presents different means how to implement MHD phenomena during single crystal growth. It should be emphasized that in all the modifications given in Fig. l additional energy introduced into the melt cannot influence directly the crystallization process since it is incomparable to the energy of molecular forces. Both the influence and efficiency of MHD means are determined solely by the change of motion, heat and mass transfer characteristics."

Jan 1, 1998

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By M. Save, N. Menad

"This paper gives the overview of different alternatives to recycle the following wastes: slag, dusts, wastes of electric and electronic equipment (WEEE) and auto shredder residues (ASR). Based on modified Bogue calculations, steelmaking slags were combined in order to produce a belite-rich clinker activated with sulphoaluminate. The EAF dusts containing significant amount of metals can be recycled in different ways: The carbothermal treatment and INTECT process are reported. The results obtained from the model of Auto Shredder Residue injection into blast furnace show that ASR can be used as reducing agent in the BF process if certain conditions are met. The particle size of this material must be controlled to ensure optimal gasification of the material in raceway. The non-ferrous contents may affect the pig iron quality, which is difficult to rectify at a later point. It seems the pyrolysis is the most attractive process to handle ASR. The BRGM flow sheet of WEEE treatment is also reported.I. Introduction The activities of human been may generate wastes and by their accumulation during several years, these wastes may have an impact on the environment and on the human health. These wastes can be generated in the forms of solid, liquid and gas. A variety of industrial wastes can be recycled for use as products. There are three ways in which industrial waste recycling occurs: at the facility itself (on-site recycling), at commercial facilities that gather waste streams from several companies (off-site recycling), and at a company that uses as inputs in its production process the waste products of another company. The industries producing iron and steel may generate different solid wastes which are classified in three main categories: 1. Ferrous material (mainly dusts and sludges from gas cleaning), 2. Slags (these by-products are generated from different process stages), 3. Others by-products (including refractories and material generated from engineering activities). According to this review, the most quantity of the metallurgical wastes is deposed. Currently, the public opinion opposes the creation of new sites. This leads to the growth of the waste disposal costs. Such situation reduces the enterprise competitiveness and decreases their market share on regional and/or national and/or world scales. In these conditions, the economical activities can be decreased leading probably to social problems. The problem of wastes and/or by-products can be treated on three levels:"

Jan 1, 2008