Search Documents

By H. Hirayama, T. Okura, O. Kato

"Saganoseki Smelter & Refinery, one of the largest copper smelters in the world, has the annual capacity of 300,000 metric tons in copper content with two flash furnaces, six Pierce-Smith type converters, two anode furnaces, four acid plants, three tank houses and perfect pollution control system.Coping with the many severe conditions surrounding the copper industry in the last decade, Saganoseki Smelter has kept performing the stable operation, while enhancing the smelting capacity and developing new technologies such as the hydrometallurgical treating of converter dust recovered at electric precipitators. Especially in the operation of flash furnaces, which are of Nippon Mining's conversion type using hot air in a temperature of l,000ºC some technological improvements and complete operation control factors have approved the concentrate feed rate to reach to 2,200 tons a day for a flash furnace.Reported in this paper are the production control design for copper smelting process, and the operation control scheme of the flash furnace following the brief review of the characteristic of Saganoseki Smelter's process and some improvements. Copper Smelting ProcessDescriptions of major unit operations and general specifications of the copper smelting facilities are summarized in Table 1, and the present flowsheet of the copper smelting is described in Figure 1 (1,2).Outputs and raw materials treated in the last five years are shown in Table 2, in which concentrate includes powder copper scrap which amounts to 3 to 4% of concentrate.A full operation was performed for a period of one month, for both one flash furnace operation and for two flash furnace operation. With one furnace operation, 19,200 tons of copper were produced. With the two furnace operation, 84,000 tons of concentrates were charged and 33,500 tons of anode (net 28,600 tons of copper) were produced.The actual production level, however, has been kept at 80 to 90% of the full capacity because of low copper price, tight market of copper concentrate or fall of net demand in Japan."

Jan 1, 1989

By Chu Bo-Yi

"This paper contains a comparison of creep-feed and shallow-cut grinding on ceramics with both neat oil and water-based grinding fluids. When a water-based grinding fluid was used in creep-feed grinding on ceramics the vertical forces and specific energies increased markedly fast with result that the wheel surface was damaged seriously. Creep-feed grinding on ceramics with neat oil not only produced much lower grinding forces and specific energies but also resulted in the wheel remaining in good condition and minimizing damage to the ground surface. This finding may lead to a deeper understanding of the behaviors of grinding fluids in grinding processes both on ceramics and metal as well.1. IntroductionAs advanced ceramics are obtaining more and more applications in the technical area, some machining processes are needed after the sintering to reach the accuracy and finish required by components. Because of higher hardness and brittle behaviors of modem ceramic many researches have been done in order to improve grinding efficiency and surface quality.In the grinding metals the concept of creep-feed grinding has been developed in industry as a real alternative to the normal method of shallow-cut grinding. In addition to the general economic advantages, dimensional accuracy and surface integrity are invariable improved using the creep-feed grinding technique.In grinding ceramics former studies have done many works on both creep-feed and shallow-cut grinding on ceramics with water-based grinding fluids since the water-based were thought to be better coolants than neat oil in most tests of grinding metals[l]. It was suggested that the specific grinding energies of ceramics are markedly higher in creep-feed grinding. The grinding force increases vary rapidly with time in the creep-feed case. In other words, so-called speed stroke grinding with high workpiece speed is considered more suitable for improving the grinding efficiency [2][3]."

Jan 1, 1998

By D. Zhao

High temperature deformation characteristics of austenitic 304L, and martensitic 410 and 416 stainless steels were investigated by conducting compression tests over a wide range of temperatures and strain rates (950-1250 C and 0.001-20 s-1). Flow behaviors of the three alloys were characterized. Optical metallography was performed to determine the as-deformed microstructures. The flow behaviors were related to microstructural phenomena during high temperature deformation. Dynamic recrystallization was responsible for the flow softening. Both dynamic and static recrystallization were operating, and the recrystallized grain size increased with increasing temperature and decreasing strain rate. Strain rate sensitivity was found to increased with increasing temperature and decreasing strain rate. No defects such as cracking and shear bands were observed at those test conditions. Preferred processing conditions can be selected by considering as-deformed microstructure and strain rate sensitivity.

Jan 1, 1994

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By Milan Lj. Stamatovic

The hydrometallurgical recovery of zinc from recycled blast furnace dust from a steel plant (Smederevo Metallurgical Company, Yugoslavia) was investigated. The dust contained 22% Fe, 17% Zn and 0.2% Pb. X-Ray diffractometry showed that the main components were hematite and magnetite, in combination with zinc oxide. Individual particles were generally spherical and ranged in size from 10 to 150 microns; 63% were less than 33 microns in diameter. An effective hydrometallurgical approach proved to be by caustic leaching and electrowinning. Recovery of zinc in the form of zinc powder was over 90%; this material can be used for the cementation of impurities in the conventional hydrometallurgical process for zinc production.

Jan 1, 1994

By R. J. McClincy

The potential techniques for the direct smelting of copper sulfide concentrates to blister copper were evaluated from the standpoint of commercial application. Many existing smelters are adaptable to direct smelting practice but only with improved control of metallurgical performance. Modified and innovative procedures for slag cleaning and metal refining, prerequisites to direct smelting, are presented and discussed. The ability to smelt directly to blister copper using existing equipment and eliminating the need to convert matte offers ,significant advantages to traditional smelting practice from the viewpoint of cost, 'S02 control, and process simplicity.

Jan 1, 1983

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk's present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By B. Yalamanchili

Gerdau Ameristeel Beaumont presents its systematic approach for upgrade decisions that has developed over 30 years of ongoing capital projects for quality and cost improvements. This system serves to identify product needs, select process improvement strategies, justify them, and assist multi-department communications and decision-making. This is illustrated with Beaumont mills? last Stelmor upgrade and leads to a discussion of the need to consider Life Cycles of both products and technologies as we move to answer the challenges of the future.

Jan 1, 2006

By Jae-Ho. Lee

Mercury is a toxic contaminant encountered in the extraction of gold from mercury-containing ores. It is found in the leach solution of CIP circuits and in the cathodes of the electrolyte cells used to electrodeposit the gold. The research conducted has examined the potential for selective removal of mercury from synthetic Au-Hg-CN electrolytes containing only gold, only mercury, and both gold and mercury. Cyclic voltammograms were obtained for mercury- coated copper electrodes with these cyanide electrolytes. Exchange current densities were determined from the voltammograms in the low overpotential region. Laboratory scale batch- electrolysis at constant current was also conducted for the electrolytes containing only mercury and both mercury and gold, at 20 and 50°C and from which the kinetic behavior associated with the process was analyzed. The surface of cathode before and after electrolysis was also characterized and a copper mercury intermetallic (CyHg,) was identified. Gold codeposited with mercury during the later stages of electrolysis. The results of this work corroborate that the mercury-amalgam copper electrode offers a viable electrochemical technique for the selective removal of mercury, however a high-surface-area cathode-cell would have to be utilized to provide for the desired selectivity.

Jan 1, 1994

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to to7 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By Paykan Safe

Computational Fluid Dynamic (CFD) modeling provides a powerful tool to assist with the design of ventilation and fume control systems in smelters and other high temperature metallurgical facilities. For this paper, this tool has been used to analyze the off-gas flow patterns exiting the mouth of a Peirce-Smith converter into a water-cooled hood and drop out box. The effects of various process and physical plant design parameters on process gas and fume capture and potential build up on the converter hoods was examined, and the optimum design and operating parameters were determined.

Jan 1, 2000

By Nozomu Uchida, Uematsu Keizo, Daisuke Shouji

"Grain orientated microstructure was developed for the improvement of ceramic characteristics. Novel polarized light microscopy was developed to examine the grain orientation quantitatively. The degree of grain orientation was estimated from the retardation determined with a Berek compensator. The method was essential to determine a minor grain orientation, which could not be analyzed by means of conventional X-ray measurements. The data were favorably related to ceramics characteristics. The comparis of the ceramics with various degree of orientation was very important to explain the change of ceramic characteristics with processing.IntroductionMicrostructure with grain orientation has a high potential for greatly improving characteristics of ceramic. However, there has been strong restriction on processing and material for developing this structure. It has been crucial to apply forming methods involving high shear such as injection molding1). Grains must have an elongated shape.In recent years, much attention has been paid on the effect of high magnetic field on diamagnetic materials2)3)4), Many ceramic materials are known to be diamagnetic. High magnetic field has a high potential to orient grains. The principal driving force for grain orientation is the magnetic anisotropy of material, which is generated by non-cubic crystal symmetr5). This method of grain orientation is not restricted by grain shape, and can be applied to all materials having non-cubic crystal structure.This study uses alumina as raw materials, and produces alumina ceramics with orientated grain in high magnetic field (10T). Alumina has a magnetic anisotropy due to hexagonal crystal structure. The degree of grain orientation in the green and sintered bodies will be examined and their relevance to magnetic field will be discussed."

Jan 1, 2000

By James D. Navratil

Ferrites have been used to separate a wide range of substances such as dissolved metal species, particulate matter, and organic and biological materials; they have been used almost exclusively for metal waste treatment applications. The versatility of the ferrite waste treatment technique is evident in the wide variety of application methods. Furthermore, ferrites can be used to remove selected impurities in feed solutions containing metal products requiring purification. A brief overview of ferrite properties and recent applications for metal recovery and waste processing will be presented.

Jan 1, 1990

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO = Zn(g) + CO2 This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction does not occur at an appreciable rate, as is expected from thennodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide coneentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By W. F. Ranson, R. C. Progelhof

"I. THE PROBLEM: MANUFACTURING PRODUCTIVITYThe 1985 President's Commission [I] on Industrial Competitiveness found compelling evidence of the declining economic position of the United States in world markets. The annual rate of increase in the United States productivity is approximately one-seventh that of our major trading partners over the last decade: profit levels in manufacturing investments are below those of the mid-1960's; an increasingly negative trade balance since 1971; and a sharp decline in the United States share of world trade in manufactured goods for more than two decades. A particularly dramatic example of the shifting economic balance is the fact that Japanese productivity growth has been five times greater than that of this country since 1960. In face, Japan's productivity now exceeds that of the United States in such critical industries as steel, transportation equipment, electronics and electrical machinery.American employees have experienced the competitive consequences of this nation's lagging industrial performance. Between 1980 and 1984 alone, the population of non-farm employees engaged in manufacturing dropped from 22.4% to 20.6%. This reduction in manufacturing must be arrested.Commissions RecommendationsThe comprehensive set of recommendations offered by the President's Commission recognized the nation's ""key competitive advantages"", technology and human resources, and calls for their strengthening. Particular emphasis is placed on manufacturing technology and the fact that this country does not translate research into new technologies rapidly and fully.""Perhaps the most glaring deficiency in America's technological capabilities has been our failure to devote enough attention to manufacturing or 'process' technology. It does us little good to design state-of-the-art products if within a short time our foreign competitors can manufacture them more cheaply. The United States has failed to apply its own technologies to manufacturing. Robotics automation and statistical quality control were all first developed in the United States but in recent years they have been more effectively applied elsewhere""."

Jan 1, 1988

By Richard D. Hagni

Reflected light microscopy is routinely applied to the study of ore minerals and textures in polished sections prepared from a wide variety of ore specimens. With the increasing interest in environmental problems, the important role of the reflected light microscope in the precise phase identifications and the determination of the textural relationships between those phases needs to be recognized. Among other environmental applications, the microscope has been applied to the recognition of lead smelter particles from remote collect sites in Missouri and those particles have been compared to dust particles from specific localities at the nearby lead sinter plant and lead blast furnace. Dust from a secondary copper refinery has been studied for its mineralogy. Soils in the vicinity of a Missouri lead smelter have been studied for their mineralogy in preparation to the clean up of those soils. Electric arc furnace (EAF) dusts, recently classified as hazardous waste by the EPA, have been examined for their mineralogy and textural intergrowth in order to better evaluate proposed metallurgical treatment procedures to render the dust non-hazardous. The initial products from experimental metallurgical treatment of EAF dusts also have been studied to aid in determining the effectiveness of those treatment procedures. Refractory gold sulfides that have been roasted in the presence of lime to retain environmental objectionable sulfur and arsenic while recovering the gold have been studied by RLM to determine their mineralogy, porosity, and permeability for cyanide leach solutions. These case histories illustrate the applicability of ore microscopy to the study of problems related to environmental concerns.

Jan 1, 1995

By Klaus-Markus Peters, Robert M. Cravens, James G. Hemrick

"Degradation of refractories in molten aluminum applications leads to energy inefficiencies, both in terms of increased energy consumption during use as well as due to frequent and premature production shutdowns. Therefore, the ability to enhance and extend the performance of refractory systems will improve the energy efficiency through out the service life. TCON_ ceramic composite materials are being produced via a collaboration between Fireline TCON, Inc. and Rex Materials Group. These materials were found to be extremely resistant to erosion and corrosion by molten aluminum alloys during an evaluation funded by the U.S. Department of Energy and it was concluded that they positively impact the performance of refractory systems. These findings were subsequently verified by field tests. Data will be presented on how TCON shapes are used to significantly improve the thermal management of molten aluminum contact applications and extend the performance of such refractory systems.IntroductionThe production of molten aluminum creates aggressive environments for processing equipment, thereby requiring refractory materials to contain the aluminum during melting, transfer, treatment, and casting operations. Degradation of these refractories not only causes issues with reduced product quality and production yields, but also increases heat losses as the insulative properties of the refractories are compromised. Furthermore, in addition to disrupting production output, refractory failures lead to further impacts upon energy efficiency as large amounts of energy are lost during the cooling and subsequent reheating of the equipment as the refractory linings are repaired or replaced.The need for improved refractory materials is recognized throughout the industry. A joint U.S. Department of Energy and industrial workshop held in 2000 on applications for advanced ceramics in aluminum production [1] noted that refractory materials used in melt processing equipment have many limitations. The workshop report noted that these issues may be addressed by using advanced ceramics, but new materials must be cost effective when compared to current refractory materials. Also, in 2005 the Canadian aluminum industry produced a technology roadmap [2] having the goal of identifying and bridging gaps between current technological resources in the industry and future requirements. One of the areas identified as being crucial to the future of the industry was the need for improved molten aluminum-resistant materials."

Jan 1, 2009

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.