Search Documents

By David C. Lynch

FeCl3 particulate of 10 to 100 um in diameter was reacted with radicals produced in an oxygen plasma at pressures between 1 to 20 Torr. The particulate, in a fluidized bed, was positioned above the plasma to avoid over heating the oxide product which is known to lead to crust and clinker formation[ 1 ]. Reaction between the iron chloride and the gas phase occurred at temperatures between 66 and 226 °C. Oxygen radicals react with the surface material to a depth of approximately 2.5 4m. Surface material, analyzed with a x-ray technique, indicates that the maximum amount of FeCl3 reacted on a weight basis was found to be approximately 67%. More typically, 40 to 50 wt% of the chloride was reacted within 30 minutes to 1 hour.

Jan 1, 1996

By C. A. Landolt

Inco pioneered the use of tonnage oxygen in non ferrous metallurgy when it commissioned the first .industrial oxygen flash smelting process for the treatment of copper concentrates in the early fifties. This technological innovation was followed by other applications of technical oxygen. Inco is currently implementing a Sulfur Dioxide Abatement Program designed to reduce S02 emissions from the smelter by 60% in 1994. The new flowsheet includes new equipment for the oxygen flash smelting of Cu-Ni concentrates and for flash conversion of chalcocite. Oxygen smelting and converting technology will lead to a substantial decrease in use of fossil fuels and to generation of high strength S02 off gases suitable for efficient fixation in a new acid plant.

Jan 1, 1992

By Zhong g. Shui-ping

A new type Pb-Ag (0.8wt%)-Bi (0~5.0wt %) alloy used as anode in electrowinning of zinc from sulphuric acid electrolytes was prepared. The electrochemical properties of this ternary lead alloys have been tested and compared with those of Pb-Ag (0.8wt %) anodes used in industry. Results show the anodic overpotential decreases with the increasing of Bi content in the alloys. When the content of Bi was 1.0 wt% and 5.0 wt%, the anodic overpotential is about 40?50 mV and 60?80 mV lower than that of Pb-Ag (0.8wt %) alloy, respectively. The formation of oxide layers on the surface of these alloys was traced by LSV methods and the composition of the anodic oxide layers was characterized by XRD and SEM analysis. The surface layer on the two type anodes examined is mainly composed of a?PbO2 and ß?PbO2. But different structure of the surface layer was observed, Pb-Ag (0.8wt%)-Bi (1.0wt %) has a more fine-grained structure as compared to Pb-Ag (0.8wt %). But the film on Pb-Ag (0.8wt%)-Bi (3.0wt %) alloy is rather friable, cracked and not tightly attached to the anode.

Jan 1, 2008

By P. Stantke

In recent years the CollaMat process has been used successfully worldwide in a number of copper electrorefining tankhouses as an instrument for measuring the glue concentration and optimizing cathode quality. Owing to its measuring principles the CollaMat can be used not just for measuring the concentration of active glue but also the activity of other substances, which have an impact similar to glue on the copper deposition. In SX-EW plants guar is frequently used instead of glue as a levelling additive. In our laboratory the effect (activity) and the decomposition rate of guar in copper electrolyte was examined. As expected, the results show that guar has an effect similar to glue on the copper deposition. However, at the same temperature, a greater quantity of guar is required to achieve the same results. As with glue, the decomposition rate (due to hydrolysis) of guar is strongly dependent on the temperature. Therefore, in practice, its on-line monitoring is necessary to guarantee the same guar activity at any time.

Jan 1, 1999

By Mark C. Bronson

The feasibility of several pyrochemical approaches-for separating non-radioactive constituents from ICPP HLW calcine were examined. The removal of aluminum as AICI3 from aluminia calcine was successfully demonstrated. The examination of pyrochemical processes to remove non-radioactive constituents, primarily aluminium, zirconium, calcium and fluorine, from zirconia calcine showed that fluorine removal was required in order to chlorinate the calcine. A molten calcium chloride wash, a calcium reduction, and. a sulfuric acid treatment were examined as possible zirconia calcine pretreatment options for fluorine removal. Fluorine removal from simulated ICPP zirconia calcine was demonstrated by both a CaCl2 wash method and a sulfuric acid treatment method. X-ray fluorescence analysis indicated that greater than 97% of the fluorine can be removed by either method. Fluorine removal by a calcium reduction using an alloying agent, zinc, or a calcium reduction using, a filtration separation were also demonstrated, but the efficiencies of fluorine removal were considerably less ranging from 50 to 90%. Regeneration of CaCl2 from the salt and oxide residues of the CaCl2 wash experiments was also demonstrated 'by an aqueous dissolution method. From the salt residue, 85% or more of the CaCl2 was recovered and contained little if any CaF2 or CaO. From the oxide residue close to 100% of the CaC12 was recovered. Because of the overall success of the CaCI2 wash, it was determined to be the preferred fluorine removal process. The sulfuric acid treatment to remove fluorine is effective, but the proposed overall flowsheet has not' been adequately demonstrated.

Jan 1, 1995

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By Ashok D. Dalvi

Production of nickel from laterite ores has occurred for over 100 years beginning with processing of garnieritic ores from New Caledonia. However, until now the world nickel supply has been predominantly from sulfide sources. Going forward, the authors project that the production of nickel from sulfide ores will remain more or less constant. Most of the expansion in nickel production capacity over the next ten years will come from processing of laterite ores. Thus the capital and operating costs of new laterite projects will have significant impact on the nickel supply and therefore price. The authors have reviewed the history and capital and operating costs of various recent laterite projects and capital and operating costs of these projects and those "on the drawing board". The authors have also evaluated the risk associated with such projects. The paper will discuss the impact of this and the recent history on the future development of laterite nickel projects.

Jan 1, 2004

By A. F. Usov

"The use of the Electric Pulse Discharge method of materials destruction (EP) for disintegration of materials in an industrial-waste processing are examined. The principles and Experience of the development device of EP-disintegration have been described, the technological efficiency of disintegration of industrial minerals estimated.IntroductionThe Russian scientists have proposed and comprehensively studied the electric pulse (EP) technique which is applied in ores and materials disintegration [1, 2 ]. The different aspects of the problem have been presented by the authors in papers at many international congresses [3-6]. Recently the technique is intensively developed in many countries, and various disintegration installations are exhibited.Crashing and disintegration of ores by EP-method is characterized by high selectiveness of destruction. It provides better disclosure of mineral grains and prevent it from destruction. EPmethod reduces slurry formation. All this provides better mineral extraction at ore beneficiation and improves concentrate quality. It also prevents the product from polluting with equipment metal, inwall and grinding equipment material. The possibility to change the character of dynamic loading allows controlling grain-size composition and getting small-size product in contrast to mechanical method of crashing.The product of EP-crashing is characterized by less toughness and greater specific surface area of grains since the new surface is formed at splitting and chinks extension. The product is of high sorption and reactivity in chemical changes. Open grains of mineral spots correspond to their natural condition and it is of great importance for studying mineral.The principles of the development deviceLong-term studies of the technique carried out by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute ""Mekhanobr"" (S.Pertersburg), made it possible to substantiate principles of the disintegration installations design, make exploratory stands and technological installations to carry out pilot tests and operations under production conditions. The construction design of disintegrating installations depends on many technological and physical factors. Of all the technological factors, the most significant one is to preserve the liberated product because it is the peculiarity of the EPdisintegration to have high selectivity of disintegration. The preservation of the mono-mineral product liberated from the rock mass means that this product is not overgrinding, which causes the loss of the product with slime in processing, and that the initial natural form of the mineral inclusion is also preserved because it is the size and the integrity of crystals that determines its cost value (precious minerals). On the one hand, it is provided by a stage disintegration technique, with the product classified after each stage, and, on the other hand, by selection of specific conditions of electric breakdown, which ensure high performance of electric breakdown and effective disintegration of material fragments, with the useful mineral inclusions preserved intact, with its size considerably exceeding the discharge gap. These conditions are provided by the appropriate geometry of electrodes, the discharge gap and the screen size due to the material’s nature and grain size."

Jan 1, 2008

By Yoshiaki Suzuki

Since 1973, Saganoseki Smelter & Refinery had operated two flash smelting furnaces together to produce 330,000 mtpy of copper. However, in 1990's, economical situation required the smelter more increased productivity to remain competitive. The program, to integrate two flash furnaces into one was carried out maintaining the same production. Modifications were done on the pneumatic concentrate drying system, concentrate feeding system, concentrate burner and furnace cooling system, etc. to double the, furnace throughput. A new large cryogenic oxygen plant was constructed replacing two old plants. Single flash smelting furnace operation has started in March 1996. This paper describes about details of modifications and operational results.

Jan 1, 1998

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

The carbon composite brick is a new refractory used in blast furnace hearth and bottom. It caused wide attention due to its high thermal conductivity and low erosion by molten iron. In this paper, chemical constituents, SEM-EDS and X-ray diffraction were carried out in order to understand reaction mechanisms. A series of experiments of oxidation resistance characteristics were made. The oxidation mechanisms of carbon composite bricks in the presence of air were analyzed. According to the analysis on many experimental results, the oxidation process of carbon composite bricks under different temperatures were controlled by different mechanisms. In the condition of high temperature, SiO2 as oxidation product hindered the diffusion of O2, and reduced the oxidation loss of graphite in the internal.

Jan 1, 2015

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Halvor Dalaker, Pål Tetlie

The decomposition of methane has been studied experimentally in contact with various oxides at elevated temperatures. For each oxide, the temperature at which the cracking starts has been determined. No correlation was found to exist between the temperature for the onset of cracking for a given oxide and the affinity for carbon of the oxide's metallic component. In terms of potential for using methane as a reducing agent, calculations are presented that indicate that the suitability of an oxide for such reduction depends on the desired methane+oxide reaction being more energetically favourable than the methane+methane=ethylene/acetylene reactions.

Jan 1, 2014

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By Toshihiro Tanaka

The information on viscosity and surface tension of molten slag is indispensable to design new refining procedures in ferrous and non-ferrous processes. For example, the authors have tried to develop "Capillary Refining" to remove impurities in liquid metals by applying capillary absorption of molten slag with those impurities into solid fluxes which have a lot of small capillary tubes. It is necessary to adjust the above physico-chemical properties to adequate conditions on the capillary penetration. In the present paper, we discuss our recent trial to predict surface tension and viscosity of molten slag in multi-component systems. We have derived a thermodynamic model to predict the surface tension of molten slag by using ionic size, molar volume and surface tension of pure components. In addition, we have applied neural network computation to evaluate the viscosity of molten slag. We found good agreement of the calculated results with experimental values of the surface tension as well as the viscosity in various slag systems.

Jan 1, 2006

By Godwin M. Beene

Large scale mining operations started in Zambia in 1913 and rapidly expanded during the post 1930 period with the opening of several mining and processing plants on the present Zambian Copperbelt. As a consequence of poor tailings dumps design methods at the start of the mines, and in view of stringent Government Legislation pertaining to environment in the recent years, Nkana Mine has developed a unique method of dump construction at its current tailings depository, Tailings Dam 15A. This method has enabled the revegetation of the dump retaining walls while construction is still in progress, a situation which was not possible on the older dumps. Cowdung has proved to be a superior fertilizer for providing plant nutrients on the tailings. The new method of dump walls construction and walls rainwater runoff drainage system has almost eliminated tendency of gully formation which is common on older dumps, as rainfall on the Zambian Copperbelt comes in intense thunderstorms. The decanted water from the dump is discharged to the natural environment in a controlled fashion after ensuring that it meets the Zambian Government Statutory requirements.

Jan 1, 1999

The concepts of capacity and basicity have proved extremely useful in dealing with a wide range of solute species in metallurgical slags, and as a result have been widely applied. These two concepts are reviewed, and it is suggested that the Lewis approach to basicity has much to commend it. In some cases, it appears that the term capacity has been used without due consideration being given to the nature of the solution being formed, or even to whether a true solution was being formed at all. This paper proposes a rigorous definition of capacity, based on the true nature of the solution process in slags and glasses, and briefly reviews the repercussions of this approach on data available in the literature and the limitations which it may impose on future investigations in this area.

Jan 1, 1994

By P. J. Moor

Britannia Refined Metals Ltd. was built in 1931 to refine the lead bullion produced at the Mt. Isa mine in Queensland, Australia. Several periods of expansion and development have taken place over the intervening years, leading to major increases in the refining capacity for both lead and silver. A plant for treating recycled lead-acid batteries was added in 1976. This was redeveloped in the early 1990's to utilise Isasmelt technology for the smelting operations. Most recently the No. 2 refinery kettle floor was extended to enable it to process lead bullion produced from two Imperial Smelting Furnaces (ISF), at Britannia Zinc Ltd. in Avonmouth, England and at MIM Hüttenwerke in Duisburg, Germany. This expansion included the provision of a plant for the hygienic handling of drosses and skims. This paper briefly describes the present primary refining operations and gives an update on the most recent developments in the process metallurgy and operating practices that have taken place.

Jan 1, 2000

By R. G. Reddy

The oxidation kinetics of A13Ti intermetallics have been studied at the temperature range of 850°C to 100O0C in pure dry oxygen. The oxygen diffusion rates were investigated using TGA method. Parabolic rate constants were calculated. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction. A continuous A120, scales with a little TiO2(rutile) were formed on the intermetallic surface. The A13Ti intermetallic exhibited excellent oxidation resistance among the Ti-Al base intermetallics.

Jan 1, 1997

By T. J. Weitz, J. E. Micheletti

"Pegasus Gold's Beal Mountain Mine is located near the Continental Divide, SW Montana. Conventional surface mining utilizes crushing, heap-leaching, carbon absorption/desorption, electrowinning and refining to produce approximately 60,000 oz gold annually. A leach pad sits at 2,300 meters (7,500 ft) elevation. Winters are long and cold with average snow accumulations ofl-2 meters; temperatures fall below minus 40'C and wind chill temperatures below 70°C. The Beal Mountain staff has developed special tools and procedures for burying drip emitter lines, and managing the heap and process solutions to allow for uninterrupted gold recovery during the winter season. Management of water balance and spring runoff is critical to the operations' success, due to mountainous terrain, high precipitation and proximity to a fishery and elk herd. The mine has an extensive network of land application disposal (LAD) and stormwater control systems to assure environmental protection and regulatory compliance.ABSTRACT ONLY"

Jan 1, 1997