Search Documents

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By John V. Beall

GOING west from Denver on Route 6, the direct road to Grand Junction, one gets the first glimpse of mining a few miles east of Denver near Idaho Springs where the workings of defunct gold mines are visible on the sides of mountains along the highway. One enterprising company is turning a profit by showing tourists through the mine and mill and then selling them gold samples on the way out. We have always known that mining people are ingenious, but this proves it. About five and a half hours fast driving west from Denver brings one to Rifle, Colo., which is the site of the oil shale mine, retorting plant, and refinery of the U. S. Bureau of Mines. As you drive up to the mine, you can see a portal high on the face of the cliff in front of you where the mine surface plant literally hangs by its toenails. Below, the retorting plant and refinery gleam in the sunlight. Up at the mine, Fred Wright will show you how the oil shale is extracted in two benches (a third bench would be used for commercial mining) by the room-and-pillar method. In mining the top level, an underground crew of thirteen men have been able to produce 1500 tons of shale in each eight-hour shift. To do this, the mine is thoroughly mechanized. The mining method is de- scribed in the September issue of Mining Engineering.

Jan 1, 1949

By John V. Beall

Since the U. S. Metals Refining Co. works was established, around the turn of the century, near the town which is now called Carteret, N. J., it has grown to be a major producer of refined copper and the main source of that special brand known as "oxygen-free high-conductivity copper." Owing to the complex metallurgical problems arising from handling a variety of raw materials such as copper concentrate from Matahambre, Cuba, copper and brass scrap from the New York area, and domestic blister copper, the organization is geared from top management down through its 2000 employes to maintain a high degree of flexibility in plant operation. The Company is a subsidiary of The American Metal Co. Charges for the smelter furnaces, one reverberatory furnace and one blast furnace, are made up in. bedding bins so that they may be tailored to the production of a constant grade of blister copper. The reverberatory furnace smelts the .sulphide charge, which may be a blend of ten different materials but principally the Cuban concentrate, and the matte from the process is poured into a converter. This reverberatory is 80 by 20 ft, silica lined with a slag bottom, fired by pulverized coal, and continuously side-charged from the top by bottom-dump cars which keep the side walls covered. It produces a 40 to 50 per cent copper matte. The fuel-charge ratio is 4.35 tons of solid charge per ton of coal. The furnace has a capacity of 10,000 tons of charge per month and produces from 5000 to 6000 tons of slag per month which must be disposed of. About 5000 tons of converter slag is produced monthly and returned molten to the reverberatory furnace. The converter gases go through a spray chamber to a Cottrell precipitator and thence to the flue system. Smoke from the

Jan 1, 1948

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

By S. Uludag

Spontaneous combustion of coal has been studied by laboratory techniques using an apparatus in a small-scale laboratory testing. Coal?s inherent characteristics can be measured using Differential Thermal Analysis (DTA) and Crossing Point Temperature (CPT) methods. The DTA curve obtained after testing is compared with actual inherent moisture and its effect on spontaneous combustion has been investigated. It has been found that the Wits-Ehac Index increases as the inherent moisture of the sample increases. Therefore it can be deduced that liability to spontaneous combustion increases with increased inherent moisture. In addition, volatiles have a catalytic affect on self heating immediately after the inherent moisture is reduced. This is identified as stage two in the thermogram. The inherent moisture has a cooling effect during the initial stages of testing and is visible in the DTA thermogram. In addition, while an increase in carbon content means an increase in Wits-Ehac Index value, an ash content decreases the likelihood of on spontaneous combustion. Keywords: Spontaneous Combustion, Differential Thermal Analysis, Crossing Point Temperature, Moisture, Coal, Laboratory Testing.

Jan 1, 2007

By Luis Yacher

Proccesing plants currently have sophisticated regulation and control systems and there also systems of managment of the quality and laboratory variables, for the mine-plant transport managment, mineralogical extraction, characterization, maintenance managment were desgined to support specific operational business functions: to operate, maintain, control quality, manage the fleet, etc. The vision of systems dedicated to supporting specific business functions contradicts what is nowadays an integrated business operation, esenctially multidisciplinary and it which the managment and supervision process require access to heterogeneus information sources regarding their regarding their origin and managment system. The consecuence of ongoing pressure for operational excellence is the need of more "fine-lunning"of the processes must be adressed in a synchronized way. Hence, the need arises of restating the issue of operation and related information, for which a new conceptual and techonological focus is proposed aimed at the objetive of operational excellence.

Sep 19, 2006

By E. Rezazadeh Azar

Dump trucks are the main mean for hauling earth material within and outside of the construction and open-pit mining jobsites. The real-time monitoring of the material transportation trips is beneficial for proactive equipment management, volume estimation, and productivity measurement. The traditional manual observation is tedious, non-real-time, and expensive; therefore remote sensing technologies, namely GPS and RFID, have been employed for this reason. Ordinary construction videos are another costeffective alternative to monitor dirt loading and hauling operations in real-time. A vision-based system has been developed to recognize and count hauling trips. This system has three modules including object detection, tracking, and action recognition. This system processes videos taken from access roads in which it recognizes dump trucks and then tracks them throughout the viewfinder. The action recognition module is designed to reject false alarms and also terminate tracking. This way, the system is able to count the number of hauling trips and also record the time between each trip. Several state of the art computer vision algorithms were employed to develop this system. Some of these algorithms were modified using spatiotemporal information to minimize the inherent errors of the vision-based methods. The experimental results showed considerable performance of the system for practical application in the construction and mining sectors.

Aug 1, 2013

By Steven J. Schafrik, Michael Karmis, Zacharias Agioutantis

3-D or pseudo 3-D visualization of orebodies and mining related processes such as loading and tramming, are now commonly used by the mining industry. An approach is presented that can aid the engineer in creating the visualizations necessary for accurate presentations for use in public relations, safety training, production projections, reclamation plans, etc. It is shown that the creation of such digital representations of mining environments are independent of the mining package used to create the original mine design. Once a proper model has been created, any view of the areas is possible. These views can be taken from any number of stationary points or entered into an animation showing the progress of a mining construction. The paper focuses on the presentation of the steps used to accomplish the visualization and an example is for a quarry fill placement project.

Jan 1, 2002

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.

By Frederick H. Williams

THE object of this paper is to bring to the attention of those members of the Institute who are interested in the subject, a method for the estimation of manganese, which has been frequently used in the laboratory of the Vulcan Steel Works during the last eight months, and which is deemed worthy of more general use. It is simply an adaptation of well-known processes, for the purpose of determining this element in pig iron and steel. In general, the method consists in precipitating the manganese as binoxide, dissolving in dilute sulphuric acid in the presence of an excess of a standardized solution of oxalic acid, and titrating the remainder of the oxalic acid left unoxidized with permanganate of potash. For this method, therefore,. two standardized solutions are needed, viz., a permanganate solution and an oxalic acid solution. The permanganate solution is made so that 1 c.c. is equivalent to 1 mgr. of iron. By using so weak a solution and keeping the bulk of the solution to be titrated down to 75 c.c. or a little less, the accuracy of the process is greatly increased, since the final reaction is almost if not quite as sharp as if a stronger solution were used. The oxalic acid' may be of almost any strength, but if made so that 1 c.c. requires 3 c.c. of the permanganate to oxidize it, it will auswer well. The process is then, as follows : from 1 to 2 grams of pig iron or steel are dissolved in 40 to 50 c.c. of concentrated nitric acid with the aid of heat. As soon as solution is effected, in the case of steel, add gradually and cautiously, the solution being kept boiling, sufficient pulverized chlorate of potash to precipitate the manganese as binoxide. Two grams will be a great abundance. In the me of pig iron, first remove the carbon and silica by filtering the solution through asbestos and washing with concentrated nitric acid. Filter the strong acid solution in which the binoxide has been precipitated, through asbestos with the aid. of the filter pump. When it has entirely passed through wash well with water. Blow the contents: of the funnel into the beaker in which the precipitation was made and rinse the funnel with a little water.

Jan 1, 1882

By Henry Howe

FIG. 1 shows a volute aging break which developed spontaneously in a hardened and tempered steel helmet between 19 and 38 days after it had been tested ballistically. A similar break, shown in Fig. 2, developed spontaneously in a similar helmet about 40 days after the ballistic testing. In this case the rupture occurred abruptly and with a loud report. The path of rupture in this second case, though much the less regular, is the more interesting of the FIG. 1. FIG. 2. two, in that it is an approximation to two parallel volutes centered at the point of impact of the projectile, just below D. Several weeks later, after the photograph for Fig. 1 was taken, a similar doubling of the volute crack occurred in this helmet, starting from the end of the eyelash crack near A and spreading thence to the left contra-clockwise for about ½ in. The negatives from which these pictures are made have not been touched up in any way, save writing the letters on them. In both cases the trajectory of the bullet was normal to the initial surface at the point of impact, and in both the helmet passed the ballistic

Jan 2, 1919

By K. R. Miller

Thunder Basin Coal Company has two mines located in the southern portion of the Powder River Basin. 60-90 km southeast of Gillette, Wyoming. The mines are principally located on federal coal leases acquired in the late-1960's. Development plans for the Black Thunder Mine focused on dragline stripping, but environmental considerations during the mid-1970's made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lying with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age and the deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21 m thick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

MANY members of the National Societies died in service overseas during the World War. No memorial to these engineers has been set up but a unique and interesting suggestion has been made. While Edward Dean Adams, Fellow of the American Society of Civil Engineers, and Associate of the Ameri-can Institute of Electrical Engineers, ,vas in Belgium last June as delegate of the National Societies, En-gineering Foundation, and Engineering Societies

Jan 12, 1927

By Harold S. King

TWO summers ago I had the privilege of visiting No. 18 colliery at Glace Bay. Underground, we travelled along the haulage-way behind a powerful electric locomotive. The motor in this locomotive began to smoke badly and a carbon tetrachloride type of extinguisher was used several times during the trip. At the time, I noted a strong odour of phosgene. On my return to Sydney, I spoke to Mr. Harold Gordon, Assistant to the General Manager of the Dominion Steel and Coal Corporation, and warned him of the danger of using this type of fire extinguisher in confined spaces, since it is a well known chemical fact that phosgene, a dangerously toxic gas, is formed by the decomposition of carbon tetrachloride. This danger does not seem to be widely recognized, so it seems advisable that a more general warning be published. Attention was first drawn to the danger by the death of two men in the United States Navy Department subsequent to breathing fumes from carbon tetrachloride used in a fire, and when an employee of the Bureau of Mines also was overcome while fighting a fire with carbon tetrachloride liquid. These accidents led to an investigation of the decomposition products of carbon tetrachloride by a group of workers in the Research Laboratory of the Pittsburgh Experimental Station, U.S. Bureau of Mines, the results of which were published in the October, 1920, number of the Journal of the .Franklin Institute (1). Their experiments were conducted by two methods. The first consisted in applying the liquids to actual fires and -to hot metal in a closed room of 1,000 feet capacity, where the gaseous products, mixed with air, could be retained and analyzed. The second method was to pass the vapour:s in air through heated tubes of iron or quartz, where the humidity of the air and the temperature could be controlled.

Jan 1, 1939

By Robert Glass Cleland

FROM the time of its organization down to 1917, a period of more than eighty years, Phelps, Dodge & Co. was seldom involved in what could be called a major labor difficulty. Behind this remarkable record lay both a philosophy and its practical application. The philosophy was an attitude toward society called the Golden Rule. That philosophy had been a living principle in the lives of the founders of the company, Anson Phelps, Daniel James, and William E. Dodge. Their successors, William E. Dodge, Jr., and Daniel Willis James, accepted the same philosophy. Dr. James Douglas governed his life by it. All of these men and their families had given tangible expression to that conviction in benefactions of great magnitude and variety-churches, hospitals, educational institutions, libraries, missionary undertakings, and other organizations for human betterment, such as the Young Men's and Young Women's Christian Associations, and the development of model communities about their mills and factories. According to the best standards of their generation, they had sought to improve the condition of labor,

Jan 1, 1952

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Dan Mancuso

This case study is an example of how Encyle/Texas, Inc. (a subsidiary of ASARCO) responded to various socio-economic forces by converting an idle zinc hydrometallurgical refinery into a metals recycling facility. The facility accepts metal-laden process waste streams and produces various "synthetic ores" which are sold back to industry. Acceptance and reactions by industrial, political, economical and regulatory interests towards the project are also discussed.

Jan 1, 1992

By C J. Moran

Given that the mining industry is committed to sustainable development principles and that Australia is experiencing changes to the regulatory environment that aim to modernise the water sector and encourage adoption of consistent approaches, there is a well defined need for the Australian minerals industry to develop a water accounting framework. This requires: key terms and definitions for water metrics for use in the Australian minerals industry that is consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current requirements were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (water loss through evaporation is an example). The adopted terms and definitions dictated model development, with the conclusion that a systems approach was the most effective calculation process. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and can be adopted as the first step towards developing national water accounts for the Australian Minerals Industry.

Jan 1, 2009

By R. J. Cocks

Water auditing and water efficient practices are evolving as the quantitative tools for water balance reporting in the mining and minerals processing sector. This paper was written to describe the process of water auditing in a gold mining environment. It will contribute towards building an appropriate water management framework for The Cooperative Research Centre (CRC) for sustainable resource processing (CSRP). The research assists with the assessment of water balances in mining and hydrometallurgical processes and provides, on the ground, steady-state data for ongoing probabilistic modeling underway at most of Newmont?s gold mine operations. Five Newmont case study mine sites including the Tanami Granites Goldmine are central to this PhD water project study. The function of the Tanami-Granites water audit exercise was to measure a controlled flow of various water quality types and set a framework to establish further research for water efficiencies and water conservation in mining.

Jan 1, 2009