Search Documents

By Anthony Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. In this sense, the paper point out the GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. GIS’s proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Aug 25, 2002

By B. Tolwinski

Long-Term Open Pit Scheduler or L-TOPS is a new software package for evaluating, planning, and design of open pit mines. L-TOPS transforms geological, economic, and technical information about a mineral deposit into a detailed mining schedule that maximizes economic efficiency without neglecting the practical requirements of mining operations. L-TOPS has been customized for integration with Placer Dome Inc.'s existing in-house resource/reserve optimization software to function as a primary tool for property acquisition studies and for the designing of mines for feasibility studies. This pa-per presents an overview of L-TOPS and reports on its application to Placer Pacific's (Placer Dome's Australian affiliate) Mt. Rawdon project.

Jan 1, 1996

By A von Johannides, G J. van Hout, L F

In the past various systems have been used to plan the extraction of ore from block cave operations. These systems have varied from rather sophisticated models with empirical ægravity flowÆ rules applied to the very rudimentary models where only the recorded mined tonnageÆs have been accounted for against the available resource. The normal requirement of these models has been to only plan the movement of ground through the drawpoints. Little cognisance has been taken of the other parameters that affect the total mining operations. The intended purpose of the linear program planning system is to not only include the management, resource availability and geotechnical constraints, but to also include the mining rules. The paper will discuss the various constraints that have been considered, and attempt to illustrate where the system better serves the production system than previous ones. A brief technical discussion on the linear programming system is included.

Jan 1, 2000

By Anders Erlandsson

"The crude ores from the LKAB mines are sorted and refined into a number of products. As there are a number of different plants the flow of material is often complex.in connection with studies of a proposed extensive investment program it was necessary to get a good measure of the changes which would be caused in the total profit by the different possible investments. A linear programming model was set up to accomplish this, and to cover the consequential effects on the production system. The objective function of the model maximized the total profit, taking into account restrictions in materials balances, blending conditions, production capacities and market. The changes in total profit resulting from the different investment alternatives, together with investment and fixed costs, were used in a series of investment analyses. The application has proved to be very successful and the results come very near to what was expected."

Jan 1, 2014

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By D J. Thobaven

Project financing challenges caused by declining commodity prices have heightened the need to improve project metrics such as minimising capital payback and maximising net present value (NPV). Khnaiguiyah Mining Company (KMC) recognised the need to improve early cash flows at their Khnaiguiyah zinc-copper project after initial studies showed the project could not provide the desired financial outcomes necessary to compete for investment dollars in the current market.A significant improvement to the project cash flow in early years was realised through simultaneous optimisation of cut-off grade, mining sequence and strategic stockpiling. This improvement was achieved by accelerating mining in the pits, stockpiling lower value material and feeding higher value material directly to the plant. The schedule required higher mining and stockpile capacities than the sequential mine plan although minimal change occurred in the definition of ore and waste as measured by tonnes and grade. The practicality of the strategic schedule was demonstrated by implementation in the production plan with excellent conformance.CITATION:Thobaven, D J, 2014. An application of simultaneous optimisation – improving the payback period of a zinc-copper open cut project, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G. O. Prickett, P. Somasundaran

An application of the statistical and computer techniques in basic mineral processing research is illustrated by means of a case history involving the study of starch adsorption on calcite. Multi-factorial experimental designs and computer techniques were used for determining the effect of different system variables, such as solution pH, sodium oleate concentration and starch concentration, and to obtain a mathematical model of the response. Response maps enabled the investigators to see the effects clearly and to predict the results of changes in factor levels within the design region. Use of time-shared computers and plotters made data processing and analysis efficient and relatively inexpensive.

Jan 1, 1973

By R. Maurice King

In the operation of today's large scale ore-processing mills, it is extremely important to have some way of making an objective evalu¬ation of the performance of the available flotation reagents. Attempts to do this may often result in inconclusive findings since the magnitude of the difference in the mill results for any two reagents is apt to be quite small compared to the variability introduced by the process and 'the analytical procedures used to measure them. In cases where two reagents give vastly; different mill results, evaluation becomes a simple matter and as such deserves no further attention here. A question of primary concern, however, is how a mill can go about evaluating the performance of two reagents which may, for example, give a difference of only 0.001% copper in the-tailings or of 0.2% in copper recovery. The casual observer may feel that such small differences may be of little importance, but in a mill-whose daily tonnage is between 30 and 40 thousand, these differences could mean a substantial savings. Before the presentation of an actual example of a reagent testing scheme designed for just this-purpose, perhaps a few minutes should be devoted to a review of some statistical methodology to be used later in the discussion.

Jan 1, 1964

Principal component analysis of the variation of Cu, Ni, Zn, Pb, Mn, and Cr in a control group of 96 samples of surface ironstone from the Yilgarn Block, Western Australia, was used to derive a simple graphical method, based on only Cu, Ni, and Cr, for discriminating between massive nickel gossans and other ironstones.When the graph was tested by plotting 400 control samples, it failed to correctly classify only nine out of 176 gossans and 11 out of 224 other ironstones.

Jan 1, 1974

By Gordon Lewis

A complex mixture of hydrated reaction products is obtained from hydrothermally treated refractory cements and castable concretes. TGA can be used both to identify the product phases in the mixture and to determine a quantitative relationship among the phases. When reacted mixtures contain compounds that decompose simultaneously, or nearly so, additional assumptions must be introduced in order to develop a quantitative phase analysis. It is the purpose of this paper to examine some of these assumptions and to demonstrate their application, particularly to refractory cement systems.

Jan 1, 1982

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By W Russell

The Hercudet Non-Electric Delay Blasting Cap System provides a means of achieving greater flexibility in the use of delays, using totally enclosed gas detonation circuits which eliminate the concussive effects of detonating cord trunklines in the confinement of access tunnels beneath pillars of ore. This is an account of one such pillar blast.

Jan 1, 1985

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925

By M. Yavuz

Decision Making (DM) can be defined as a selection process of the best one among the alternatives sets in order to obtain goal, and mostly has an uncertain situation [7]. Every mining engineer is subjected to a number of mining DM problems in daily mining operations. In reality, all stages of mining have its own DM problems. Most of time, engineers do not use scientific methods for DM problems. These problems can mostly be solved by the engineers according to their past experiences and practical studies. Mining engineers often use their intuition in DM process. Experience and intuition have been central to DM because of the frequent lack of quantitative data including geology, grade distribution and ground condition, as well as environmental, social and economic factors [8]. In decision process, linguistic variables become in question and decision makers may not know how these variables are computed [9]. So, the DM process may be qualitative, quantitative or combination of the two. The problem structuring and analysis process is conceptualized in Figure 1 [8]. The qualitative analysis is based primarily on the judgment, knowledge and experience of an expert (or team of experts). In a quantitative analysis, the focus is on facts and the data associated with a problem and a mathematical formulation that encompasses the objectives, variables and constraints of the particular problem. The quantitative analysis has traditionally been the subject of operation research and management science [8].

Jan 1, 2008

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

Conventional hand drawn isopach maps of the cover of the Bulli Seam are too eomplex for use in the delineation of large domains of similar cover. Isopach maps prepared from trend surfaces fitted to the cover data are much simpler in form and so provide a convenient method of delineating broad domains of similar cover.

Jan 1, 1968

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By John R. Koehler

Available barrier pillar design methods do not adequately account for overburden caving characteristics, the timing and magnitude of associated load transfers, the occurrence of unusual geologic features, or the effects of multiple-panel/multiple-seam mining. To address this problem, the Bureau of Mines, in cooperation with Cyprus Plateau Mining Corporation, conducted a barrier pillar study in a multiple-seam mine setting. Insufficient barrier width resulted in excessive load transfer to an adjacent/underlying section. Consequent entry and pillar deterioration resulted in the section being prematurely abandoned. This paper proposes an approach based on in situ measurements, which includes mine-specific loading conditions in the barrier design process.

Jan 1, 1989