Search Documents

The design of the grinding section is discussed and details are given of the equipment installed for the autogenous grinding of ores from the C.S.A. mine at Cobar.The first section of the concentrator commenced treating ore in June, 1965 and operating experience and maintenance requirements since that time are outlined.

Jan 1, 1969

By J. V. Byrnark, R. W. von Bitter

The Hibbing Taconite Co. concentrator flowsheet, which is noted for its simplicity, uses single- stage autogenous grinding coupled with two stages of magnetic separation and two stages of size classification to produce a magnetite concentrate. This paper discusses the pilot-plant development of single-stage grinding, the commercial mill grinding performance, and mill liner development. Process innovation discussion includes process control computer implementation, size classification improvements, mill speed changes, magnetic separator improvements, and quality control innovations.

Jan 1, 1987

By J. V. Bymark

It is the intent of this paper to discuss the autogenous grinding circuit at Hibbing Taconite. The scope of the presentation includes; a brief history, the process flowsheet and the steps taken to improve mill productivity, availability and metallurgical performance. Hibbing Taconite is located near the center of the Mesabi Range in Northern Minnesota 100 miles from the Canadian border and 80 miles north of the Lake Superior Port Cities of Duluth and Superior. A 105 mile railroad connects us with the port of Superior, Wisconsin, where our pellets are loaded into lake carriers for lower lake destinations. It is worthy to mention the Mesabi Range's most famous landmark which is immediately to the south of our mine area. This is the Hull Rust Mahoning Mine which operated until the mid-1970's producing more than 700 million tons of red ore between 1893 and 1973.

Jan 1, 1985

By Olav K1omstad1ien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, is the raw material for the Rana Mines which is a division of the state owned steel mill A/S Norsk Jernverk. Activities for the exploitation of the orebodies were commenced in 1902 by the English Dunderland Iron Ore Company. During its operating period the company constructed a total of two large scale concentrating plants. The activities were strongly marked by technical problems and labor disputes. Thus actual production was limited to the years 1904-1908, 1928-1931 and 1937-1939. During these periods a total of 1.9 million tons of crude ore was mined and 0.6 million tons of concentrates produced for export. The present plant commenced operations in late fall of 1964. Up to and including 1976 about 26.6 million tons of crude have been put through the concentrating plant and about 10.7 million tons of concentrate produced.

Jan 1, 1978

By Olav Klomstadlien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, are the raw material base for Rana Mines, a division of the state-owned A/S Norsk Jernverk steel mill. The iron bearing minerals are magnetite and specular hematite. The magnetite/hematite ratio varies considerably both within each deposit and from one deposit to another. The ore bodies that lend themselves to mining have generally a thickness of 30-60 m grading 30-35% Fe and 0.15-0.25% P. The grain size varies from 0.05 to 2.5 mm. The fine grained ores are hard while the coarse grained ores are soft and easy to grind. The A/S Norsk Jernverk steel mill operates both a sinter and a pellet plant, and this necessitates production of two types of concentrates. The present flowsheet is shown in [Fig. 1]. The crude ore from the pits is crushed in a 1.07-m gyratory crusher with an open side setting of 12.7 cm. The crusher product is transported by rail to the concentrator located 25 km from the mines. The ore is fed by twelve 1.22 X 1.83 m vibratory feeders onto conveyor belts which carry the ore to a surge bin ahead of the autogenous mills. The feed rate is automatically adjusted to maintain a set power load at a level suitable for the ore type being processed. The mills operate in closed circuit with twelve dual-drum screens equipped with a 0.8-mm screen cloth. Oversize is returned by gravity to the mill feed while undersize flows to the gravity separation section which consists of Humphrey spirals in three stages. The ores are very heterogenous and analysis may vary quite considerably. The quantitative need for concentrate in the steel mill may also change rapidly. The process in the concentrator must therefore be easily changed, and consequently alternative process lines have been established. This is indicated with the dotted lines in the flowsheet. Apatite is removed by flotation by fatty acids to give a final sinter concentrate of 63% Fe and 0.020% P or less. Pellet concentrate contains about 65% Fe and less than 0.020% P. The fineness is about 1500 Blain.

Jan 1, 1981

By Henry E. Swanson

In the early 1960's the Company, then named the United States Smelting Refining and Mining Company, was drilling the Continental ore body located near Fierro, New Mexico. Reserves of underground ore of sufficient quantity were indicated to build a mill. At the same time some ore from the Continental No. 1 mine was being milled at the Company's Bullfrog Mill, formerly a lead-zinc mill. The copper ore in comparison to the lead-zinc ores was very hard, abrasive, and heavy. These factors pointed out the possibility and attractiveness of autogenous grinding. While prior to this some study had been given to autogenous grinding, no large scale tests had been made. Such a program was carried out and from the pilot plant data the following was established: 1. Grinding of the ore by autogenous means could be accomplished. 2. This could be done in one stage; however, not at a satisfactory tonnage throughput rate. Thus, the use of a secondary unit has been employed. 3. Grinding in the secondary unit could be done by pebbles generated in the primary unit. This resulted in the scheme whereby the ore would be ground 100% autogenously. 4. Liberation of the copper minerals was excellent so that good recovery at a satisfactory concentrate grade would be obtainable.

Jan 1, 1976

By Gary F. Rajala, Bruce R. Greenwood

INTRODUCTION The Empire Mine is an iron ore mining, concentrating and pelletizing facility operated by The Cleveland-Cliffs Iron Company in the Upper Peninsula of Michigan. Owners of the mine are Inland Steel, LTV Steel, Wheeling-Pittsburgh Steel and Cleveland-Cliff s. The orebody is a fine-grained, low grade iron formation with magnetite as the primary constituent. Also present are iron carbonates, iron silicates, chert, hematite, goethite and quartz. The original six concentrating lines were started in late 1963. Successive expansions of ten lines in 1967, five lines in 1974 and 3 lines in 1979 have resulted in Empire reaching a present annual capacity of 8.0 million long tons of pellets. The Empire flowsheet was developed over several years of laboratory bench testing, pilot plant testing and testing of a full-scale primary autogenous grinding circuit. Since the original flowsheet was established, modifications have been made based on pilot plant and full-scale plant tests. The present flowsheet for three sections of the concentrator consists of one stage of crushing, two stages of closed circuit autogenous grinding, two stages of magnetic separation, one stage of hydraulic concentration and two stages of flotation (rougher and scavenger). The flowsheet for the fourth section of the concentrator (Empire 4) is the same as the first three sections, except a crusher has been added to crush excess pebbles. The Empire 4 flowsheet appears in the at- tached figure. PRIMARY GRINDING CIRCUIT FLOWSHEET Empire has a total of 24 individual grinding lines. However, at the present time, Line 1 is not being used for processing crude ore. The primary mill on Line 1 is now grinding flux stone for fluxed pellet production and the secondary mill is being used as a ball mill to grind rougher flotation tailings prior to a scavenger flotation circuit.

Jan 1, 1992

By Robert R. Turner, Arthur R. MacPherson

This chapter reviews the steps which should be taken from the time it is decided to consider autogenous grinding in the development of a new ore deposit or the expansion of an existing plant up until the purchase of the new autogenous mills. In this case the term autogenous includes semi -autogenous, secondary pebble mills, and lump milling as well as fully autogenous grinding systems. Also, both wet and dry grinding alternatives have been included. Before the test program it must be decided how many bulk samples are required to properly assess the autogenous grinding possibilities of the deposit. Also, a decision must be made on where and how the samples are to be ground i.e. pilot mill at site or in established location, wet and or dry grinding, etc. In the test program itself, certain fundamental data must be obtained. The testing should include enough work to determine whether fully autogenous or semi-autogenous grinding should be used and what type produces best power efficiency. Also, all the other pertinent data should be collected such as power; tonnages; feed, charge, and product sizing; circulating loads, etc. If a secondary mill is required to produce a final grind the decision on whether a pebble or ball mill should be used may require additional test work. Finally, the concentration of the mineral may play an important part in selection of the circuit and should become a part of the final testing once the grinding has been established.

Jan 1, 1978

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By Johann F. Kerl

Autogenous batch grinding tests were performed in laboratory-scale tumbling mills with magnetite, limestone, and sandstone pebbles. The influence of pebble size, feed size, mill speed and loading, and grinding time on the fineness of grinding was investigated. Comparisons were made with the results from ball mill grinding experiments.

Jan 1, 1972

By Stevenson C. H, Lynch A. J

The reasons for choosing autogenous grinding for the new Warrego concentrator of Peko Mines N.L. are discussed and the ores to be treated in the concentrator are described. The mill was designed on the basis of pilot tests carried out at Cobar and the performance of the mill has been most satisfactory both in its metallurgical and mechanical aspects. An empirical technique has been developed to predict mill performance for change in feed rate or feed size and a mathematical model of the mill is being developed for simulation and control work. The weight and size distribution of the mill load was determined at one set of operating conditions for use in the mill model.

Jan 1, 1974

By J. E. Danoczi

ABSTRACT A diamond processing plant is being designed for the Star–Orion South diamond project in central Saskatchewan. Key to the plant is diamond liberation, which occurs in the comminution section and is the process of breaking up kimberlite rock as gently as possible to minimize diamond damage, particularly in larger, high-value diamonds. Kimberlite from the crater area of a volcanic pipe is generally softer than kimberlite from the diatreme zone. Softer kimberlite, comprising the majority of Star– Orion South deposits, can be readily broken up using abrasion and attrition by autogenous grinding mills, the preferred comminution method for minimizing diamond damage.

Jan 1, 2013

By W. D. Bachman

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from Kennecott Copper Corporation's Chino mine. The efficiency with which the various samples could be ground was found to vary over an extremely wide range, even among samples taken from different locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale non-homogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully.

Jan 1, 1970

In the four articles presented on the following pages, a panel of comminution experts offer readers the benefit of their experience with autogenous grinding and forecast some of the future developments to be expected in this fast-growing field. The articles are based on an AIME panel discussion in which the authors participated.

Jan 1, 1970

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By James E. Wennen

The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.

Jan 1, 2012

By Dennis L. Murr, James E. Wennen

"The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.INTRODUCTIONIn the past 30 years or so, autogenous grinding and semi-autogenous grinding have been the comminution technologies of choice for most mining and mineral processing operations. These technologies saved both capital and operating expenses associated with the installation and operation of multi-stage crushing and screening plants required for conventional rod mill – ball mill circuits. However, SAG and AG are inherently inefficient in terms of energy consumption, especially for very hard ores. In cases of hard ore, changing characteristics of rock fed to the mills causes wide fluctuations in mill capacity, which contributes to the inefficiency. Rising electric power costs make this the most expensive unit operation used in the extraction of valuable minerals from an ore. The objective of the concept discussed here is to reduce the energy consumption in AG grinding for hard ore and eliminate the use of large-diameter steel grinding balls that are required for SAG grinding"

Jan 1, 2012

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By Bond. F. C.

Introduction Although autogenous grinding applications date back to the early years of mineral processing when tumbling-type mills were first used, there has been a renewed interest in this type of grinding over the past few decades. A review of the historical aspects of autogenous grinding is provided which follows the development of the various types of mills and processes. Wet and dry grinding operations using either autogenous or semiautogenous mills, including the Aerofall mill, are described. Em¬phasis has been placed on the test work required to evaluate the feasibility of using autogenous or semiautogenous grinding for a spe¬cific application. The factors which must be considered to establish the appropriate design criteria for these types of grinding circuits are discussed in detail. Successful application of these grinding circuits results from a thorough test program, a careful analysis of the test results, and a practical engineering approach to the design of the process flowsheet and milling equipment. Certain pebble milling applications, where the pebbles consist of the ore or rock itself, can be classified as autogenous pebble mill grinding, or better known as ore-pebble mill grinding. In the generic sense, pebble milling includes those grinding operations using a tum¬bling mill in which the grinding media consists of various types of pebbles, either ore or other pebbles, instead of metal balls. Conse¬quently, this subject is covered separately in Chapter 5, Pebble Mills. Operating data from many of the installations located throughout the world are included in this chapter. Our appreciation is extended to those companies who contributed this important information. History of Autogenous Grinding F. C. BOND Autogenous grinding, the grinding of ore by itself rather than by special metallic or nonmetallic grinding bodies distinct from the ore, has an old and honorable place in the art of mineral processing. It antedates the use of the rod mill and is only a few years younger than the development of the continuously fed rotating tumbling mill in which it is accomplished. Its history71, 72 is inextricably bound up with that of gold mining. Every important early development of autogenous grinding took place on ores of gold, except in one case of silver ore. In common with many other features of modern mineral processing, autogenous grinding would have been greatly retarded if the winning of gold had been so small a part of mining in the past as it is today. Gold unlocked the secrets of rock-on-rock grinding. In years past gold ores were crushed in stamp batteries and then flowed over copper plates covered with mercury which amalgamated the gold. The McArthur Forrest cyanide process for the dissolution of gold in a dilute alkaline cyanide solution appeared in 1890. With finer grinding it recovered more gold than could be won by amalgama¬tion alone. The first response was to stamp in cyanide solution and finer mesh screens guarding the stamp discharge. However, the fine screens greatly restricted the tonnage stamped, and they wore out rapidly. Rotating tumbling mills70, 73 were the obvious choice to grind the coarse product from stamps. Many of these were Gates tube mills; more than 1,000 of these were sold between 1907 and 1913. They were made in 6, 51h, and 5 ft diam, with lengths of 20 and 22 ft. The 5 x 22-ft size was the most popular. The term tube mill did not refer to the mill shape, but included all tumbling mills using grinding pebbles. The flint or chert rocks found along the coasts of Denmark and Normandy are probably the most durable and resistant to abrasive and tumbling wear of any on earth. They were much used in the early tube mills. The early linings were all silex or Danish flint blocks, cemented into place with portland cement. Local hard stones or cast iron blocks were also used later. The cast iron liners carried lifters and were not bolted to the shell, but were held in a tight circle against it by steel wedges hammered home between them. The first ribbed metal liners designed to hold grinding pebbles pounded into them by the mill action were developed at El Oro, Mexico, about 1905. These and the Forbes, Komata, and Tonopah types, as well as the Osborne type developed in South Africa within about five years, were very successful in reducing liner wear. They sometimes lasted two years or more, and equalled or exceeded the life of silex lining at a lower cost. Some of the types were patented. The pioneer name recorded in the history of autogenous grinding is that of Kenneth L. Graham. In 1907 at the Geldenhuis Deep Ltd. mine near Johannesburg, he ran a comparative test on two tube mills. One mill used pieces of the common gold ore, or banket, and the other used the customary imported Danish pebbles as grinding media. He published the first account of autogenous grinding.'' In a test lasting 81 days the ore pebbles showed a definite saving over the Danish pebbles. Graham's historic paper also describes the invention of B. Chew of the Crown Deep Mines of the first trammel to be attached to a grinding mill discharge. The first known account of autogenous grind¬ing printed outside of South Africa was the description of the Graham test in Mining and Scientific Press's The use of grate- vs. overflow¬discharge was also described at this time." The news of this successful test appears to have had immediate effect, for by the end of 1908 the number of tube mills on the Rand had increased from 72 to 120.76 Presumably, most of these mills were now using autogenous grinding. The ore was principally a hard conglomerate of quartz peb¬bles cemented by silica, and was eminently suitable for use as a grind¬ing media. It is unfortunate that in South Africa the new autogenous process continued to be called by its old name of pebble milling, since the name does not distinguish between grinding with ore and grinding with extraneous pebbles. For increased clarity the former is called rock pebble milling. The first historical stage in the development was what is now designated as secondary autogenous grinding, or rock pebble milling. It consists of grinding a feed all passing 'A in. or finer with ore pebbles about 2 to 4 in. in diameter. The next stage to develop was that now called intermediate autogenous grinding, where larger amounts of larger pebbles about 5 in. in size were used to grind ore which had been crushed to about rod mill feed size or somewhat finer. It was developed on the Rand and in other places where coarse stamp screens were used to increase mill tonnage. In many cases the early secondary and intermediate autogenous mills have now been replaced by conventional ball mills and rod mill-ball mill circuits, with the object of further increasing grinding capacity. The third stage to develop is designated as wet primary autogenous grinding, in which run-of-mine ore or a primary crusher product is all fed to the autogenous mill together. It developed many years later indepen¬dently in the United States and in South Africa. The fourth and most recent stage is that of dry primary autogenous grinding, which developed in the United States and Canada. All four stages originated in gold mining. The first use of commercial autogenous grinding outside of the Rand apparently took place five years later in 1912 at the Santa Gertrudis gold mine at Pachuca, 55 miles northeast of Mexico City. This was followed closely by an installation at Goldfields, Nevada, in 1914-1915. The first name associated with autogenous grinding

Jan 1, 1985

By J. Donnelly, A. V. Deev

Substitution of coal and coke by renewable carbon (charcoal) is a low-risk and low-capital path to 50% or more reduction in net CO2 emissions by the steel industry. However, the high cost of charcoal and its low availability in most countries are barriers for the implementation of this approach. Development of an efficient wood carbonisation technology (slow pyrolysis) capable of producing large-volumes of charcoal from low-cost wood feed (e.g. wood wastes or forest residues) is an essential step towards the use of renewable carbon by the iron and steel industry. This paper provides a summary of the progress made over several years of R&D covering: (1) development and piloting of a new energy efficient slow pyrolysis process for production of charcoal from woody biomass at a competitive cost to the PCI coal, (2) techno-economic evaluation of the process. The main feature of the process is that the material undergoing pyrolysis is heated spontaneously without the supply of heat or air to the reactor. This makes it possible to carbonize large volumes of small-sized wood (e.g. wastes and residues) in a single reactor unit and capture high calorific value pyrolysis by-products

Jan 1, 2015