Search Documents

By J. E. Tiffany

FOR blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flame make their use safer than that of non-permissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless. The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.1 This paper contains a description of the methods worked out subsequently in another mine in that district.

Jan 1, 1928

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By S A. Steyn, I P. Douglas

Duvha Opencast is a large South African dragline operation supplying coal to the Duvha Power Station which is operated by Eskom, the state power utility. For Duvha to remain competitive with other collieries, it has proved necessary to continuously examine and investigate methods of reducing costs. With explosives representing a major portion of the total working costs, blasting is an obvious area of investigation.

Jan 1, 1991

By Kenneth Medearis

There is considerable evidence that more rational damage criteria need to be generated with regard to low-rise structures subjected to blasting vibrations. There is not sufficient basis for specifying a maximum ground particle velocity damage criterion such as 2 inches/second. A peak ground velocity guideline does not currently take into account a number of significant parameters, including the predominant frequencies of the ground motion excitation and the structure being excited. Although a number of states have adopted, or are adopting, maximum particle velocity criteria, such criteria have been ruled inadequate in certain legal decisions affecting blasting operations. The development of more rational damage criteria is thus of significant importance.

Jan 1, 1978

By Calvin J. Konya

Precision Blasting has designed easy to use, yet, highly powerful databases for storage and retrieval of blasting data. Three different Databases are available for blasting data management. The Vibration Data Management is a complete vibration record keeping system. The Blasting Data Management will record the information from the blasting report as well as the vibration data. The Explosives Inventory Control makes the control of explosives and initiators quick and easy.

Jan 1, 1991

By C. L. Barron, M. L. Smith, K. A. Prisbrey

SAG mill throughput is often a bottleneck to increasing plant productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility, which is also related to the rock fragmentation that is achieved by blasting. The relationship between the size distribution and fragility of the feed and the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1994

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1993

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By John E. Wiegand

This study will discuss the AMAX Coal Co., Penndiana Pipeline Project, which was conducted in conjunction with the following parties: AMAX Coal Industries, (U.S.B.O.M.) United States Bureau of Mines, (I.D.O.R.) Indiana Division of Reclamation, Ohio Valley Pipeline, Inc., New Mexico Tech, and ourselves, VIBRONICS, INC., Evansville, Indiana. The purpose of this study was to find a safe vibration level for active gas transmission pipelines near surface coal operations.

Jan 1, 1994

By Lewis L. Oriard

INTRODUCTION In recent years, there has been a trend in the direction of larger drilling equipment and larger diameter blastholes. Although this change has improved the efficiencies and reduced the costs in many operations, it has increased the potential for damage to underground openings. In addition, in many instances one now finds more sophisticated delicate instruments, automated control facilities, and a large variety of structures in proximity to blasting activity. The combined effect of larger-scale blasting activity and its proximity to various features of interest is such that there is an increased need for a more refined analysis of blasting effects and their control. BLASTING EFFECTS ON ROCK SURFACES The Breakage Mechanism In order to develop techniques for controlled blasting, one must first understand the features of the mechanisms by which blasting causes rock breakage to occur. These features have not been easy to demonstrate, mostly due to the difficulty in making tests and observations at the high stress levels and short time durations involved. When an explosive charge is detonated, the material surrounding the charge is subjected to a nearly instantaneous, very high pressure [on the order of 1.4 to 13.8 GPa (0.2 to 2.0 X 106 psi), depending on the explosive]. If the charge is coupled to "average" rock, this pressure will pulverize the surrounding rock for a distance on the order of 1 to 3 charge radii in hard rock, and to a greater distance in softer rock (this is also dependent on the type of explosive). As the pressure wave passes into the rock, high tangential stresses cause radial cracks to appear, and the nearly discontinuous radial stress zones gen¬erated by the shock front may cause tangential cracks to appear. The extent of these cracks depends on the energy available in the explosive, how quickly the energy is transmitted to the rock, and the strength properties of the rock. The discontinuous shock front is quickly dis¬sipated, but the expanding gases generate a longer-acting pressure. A compressive pulse travels to the nearest face or internal rock boundary where it is reflected in tension. The tensile strengths of most rocks are roughly 40 to %o of their compressive strengths, so the rock may now fail in tension whereas it may have been able to support the diminished compressive phase without failure. The ten¬sile deflection typically produces a failure described as tensile slabbing or scabbing. Laboratory experiments and field experience have pretty well established that several mechanisms are involved. These include (1) the classical case of tensile parallel slabbing when the pressure pulse is reflected at a free surface; (2) failure under quasi-static compressive loading (the shape is normally irregular due to discontinuities in the rock); (3) radial cracking under the action of tangential stresses at the periphery of the expanding pressure pulse; (4) peripheral cracking at the discontinuous shock front which is quickly dissipated; and (5) additional mass shifting due to the venting of the explosive gases. The first three items have received much attention in the laboratory and the literature. The complex effects of gas venting are difficult to test in the laboratory because of the difficulty in reproducing the many weak planes and discontinuities typical of most field conditions, which play such a prominent role in determining the behavior of the rock mass subjected to blasting. Unfortunately, gas venting effects can be pro¬jected to significant distances under certain field conditions, and are sometimes difficult to control. It is not unusual for gas venting to be the overriding factor in determining the final geometric shape and physical condition of the finished excavation. Sources of Damage For the purposes of this discussion, damage includes not only the breaking and rupturing of rock beyond the desired limits of excavation but also an unwanted loosening, dislocation, and disturbance of the rock mass the integrity of which one wishes to preserve (such as mine pillars, underground openings, etc.). The sources of damage include, of course, all those physical features of the rock breakage mechanism. Each of these effects must be limited to the desired zone of breakage and excavation if the integrity of the remaining rock mass is to remain undiminished. The primary zone of rock breakage usually can be controlled in the normal process of field experimentation to determine proper charge sizes and location for primary excavation. However, it frequently happens that there is damage from sources which are more difficult to account for in the design process, which are often overlooked. These are (1) the overbreak due to poor drilling control, (2) dislocation of rock (mass shifting) due to venting of explosive gases, and (3) loosening or dislocation due to the influence of seismic waves (ground vibrations). CONTROL OF ROCK BREAKAGE Importance of Geometry In studying the rock mass and blasting design con¬siderations, it is important to keep in mind the geometric relationships among charge size, shape, and position, and the physical features of the rock mass to be preserved. The features of principal interest are the external shape and position of the rock mass relative to blasting, and the position and attitude of any weak planes in the rock mass. The Sequence of Blasting and Excavation Events Unfortunately, there are too many times when the task of preserving delicate rock is considered hopeless, and because of this attitude, no further effort is ex¬pended towards caution or control. In such cases there is often a failure to recognize the importance of the se¬quence of the procedures. Attention to this can greatly reduce unwanted effects at minimum cost. Perimeter Control The requirements for perimeter control are highly dependent on the special needs of each particular proj¬ect. The desirable degree of control is a highly variable

Jan 1, 1982

By L. L. Oriard

INTRODUCTION In order to make effective plans for the control of blasting effects, it is necessary to understand a few basic principles relating to the behavior of explosives. For the purposes of discussing this behavior, it is convenient to divide blasting effects into two zones. The first zone is the non-elastic zone in close proximity to the explosive charge where rupturing of the rock occurs. For this zone, our discussion will be oriented towards the factors which affect the rock breakage, and the means of controlling the limits of this breakage. The second zone is that zone more remote from the charge location where elastic vibrations are transmitted through the surrounding medium. In this zone, we are interested in the factors affecting vibration intensity, and the means of controlling the intensity so that no damage is done to structures, utilities, or excavated slopes. It has been easier to gather data in the elastic zone, because the stress levels are lower and time durations are longer. The instrumentation for obtaining data in this zone can be less rugged and less sophisticated. Consequently, more information of ad empirical nature has been gathered. In the non-elastic zone, there has been more dependence on theory, fewer measurements, and more questioning of the validity of the measurements. In spite of these questions, there has been an encouraging advancement in knowledge in recent years, both theoretical and empirical, of the effects that take place close to the source of an explosion. When discussing the problems encountered in rock excavation, we can simplify the terminology by referring to the physical phenomena encountered in the non-elastic zone as a problem in "over-break". The phenomena in the elastic zone could be called "vibration effects". Although there is some interdependence between the two, it is possible to control the rock breakage to neat surfaces and still have very high vibration levels. Similarly, it is possible to control the vibrations to moderate levels and still have a great deal of overbreak. THE ROCK BREAKAGE ZONE First, let us discuss the effects in that zone close to the blast source that we might call the non-elastic zone. This is the zone of cratering, breakage, rupturing, and fracturing. These effects will vary with the site conditions, and a meaningful, specific analysis could

Jan 1, 1972

By David S. Shatzer, Michael R. Purcell

Current world events have demonstrated the use of commercial vehicles, other unconventional modes of transportation and unusual materials as explosives or incendiary weapons, affecting commerce, disrupting cities and even entire societies. Since the implementation of the Organized Crime Control act of 1970 the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has been investigating and studying explosives and incendiary devices and their related effects.

Jan 1, 2004

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By C. Pelley, S. Kelebek, P. D. Katsabanish, M. Pollanen

A series of small scale tests have been conducted to evaluate the effect of blasting on the grinding resistance of rocks. The samples consisted of homogeneous blocks of granodiorite and limestone while blasting was performed using single and multi hole configurations. Grinding resistance was evaluated using relative ball mill tests, rod mill tests and the SAG Performance Index test (SPI) developed by Minnovex. It was shown that the grinding resistance was affected by blasting. However the effect depended on the final product size. In the case of the coarse grained granodiorite, a negligible effect was observed for grinding below the natural grain size of the rock, while the fine grained limestone exhibited more significant changes, in the range of 13-16%. Grinding of granodiorite in the coarse size range indicated a general reduction of its work indices, as evidenced by the results obtained from the ball mill, the rod mill and the SPI tests.

Jan 1, 2004

By D T. Froedge

Before this study was started, literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast-induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet.

Jan 1, 1983

By N L. Thomas

Hole size affects many factors which directly influence fragmentation in the muckpile and hence, the cost effectiveness of the entire operation. These factors include production capability, explosives and accessories efficiency and usage and drilling accuracy. In addition, hole size should be chosen to suit the geological conditions. The paper concludes that the optimum hole size is generally the largest that can be used commensurate with production and environmental considerations.

Jan 1, 1986

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024