Search Documents

By Eric N. Baklanoff

A major problem whose importance touches the entire underdeveloped world is how to reconcile the demands of nationalism with the requirements of the international economy. Chile's copper industry presents a study of how one such accommodation has been slowly, if precariously, evolved. The dependence of a low-income country on the international economy presents, on the one hand, opportunities for speeding up the rate of development and, on the other, imposes a set of constraints on national behavior. Nationalism may be indispensable in motivating low-income countries to bear the economic costs and absorb the social changes involved in modernization, but it may also inhibit the acceleration of economic growth by its failure to come to terms with the international economy. Nationalism is a two-edged sword. An outstanding feature of Chile's economy since the mid-1920s has been its considerable dependence on the export of a single primary commodity- copper. Moreover, the affiliates of two US.-owned firms-the Anaconda Co. and the Kennecott Copper Corp.-have dominated Chile's copper industry, a fact which from time to time has posed conflict between that nation's long-range economic opportunities and more immediate political realities.

Jan 8, 1968

By David S. Graham, Paul J. Axtell

Crosshole Sonic Logging (CSL) non-destructive integrity testing identified anomalous readings near the base of a 6.5-foot diameter drilled shaft rock socket. The anomaly was confirmed to be a defect by subsequent coring and core hole camera inspection. A large void and exposed rebar were visually observed in one of the core hole camera inspections. The center of the shaft was then excavated initially with 3-foot diameter tooling and subsequently with 4-foot diameter tooling as part of the remedial actions to address the defect. While excavating with 3-foot diameter tooling, the shaft defect was not encountered. Excavation with 4-foot diameter tooling revealed the defect, a significant void around the majority of the shaft circumference. The void extended radially from the circumference of the 4-foot diameter excavation to beyond the reinforcement cage to the exposed wall of the rock socket around approximately 80 percent of the shaft circumference. CSL results and observations made during remedial shaft investigation and excavation are in good agreement. The shaft defect, located primarily outside of the reinforcement cage, was effectively identified by CSL testing. Although the defect was confirmed by investigative coring, the remedial excavation demonstrates how the investigative coring could have easily missed the defect. This paper shows how CSL results compare to physical observations made during a rare opportunity to characterize the full extent and nature of a drilled shaft defect originally identified as an anomaly by CSL testing. INTRODUCTION The case history presented here pertains to a drilled shaft for a multi-shaft bridge pier in the Midwestern United States. However, the observations presented in this paper are not a result of unique site conditions or the particulars of the project. The lessons learned from this case history are applicable to almost any drilled shaft constructed in the wet. The overall length of the subject shaft is 22 feet including approximately 12 feet of permanently cased, 7-foot diameter shaft extending to bedrock and approximately 10 feet of uncased, 6.5-foot diameter rock socket. The shaft is designed to resist axial and lateral loads and considers the contributions of side and base resistance in the axial design. Six, 2-inch diameter steel Crosshole Sonic Logging (CSL) tubes are include in the shaft. The bedrock at the shaft location includes beds of sandstone, shale, and limestone. The shaft was drilled using conventional drilling equipment and tooling, and water was used as the drilling fluid. Conventional drilled shaft concrete appropriate for underwater tremie-placement was placed via a 10-inch diameter open hopper tremie.

Jan 1, 2019

By Roberto Folchi

This note deals about the controlled demolition work for the dismantling of an industrial structure in San Seplocro, Italy. The structure to be demolished, the FLOWERS SILOS, consisted in a multilevel reinforced concrete frame supporting r.c. silos and steel silos. This was standing near civil buildings and was adjoining a warehouse that had to be safeguarded for being renewed.

Jan 1, 1994

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Amr M. Sallam

In recent years, with the increase of the number of high-rise buildings that are proposed and being built in Central Florida especially in Downtown Orlando, Augered Pressure Grouted Displacement (APGD) piles became a pronounced foundation option. The APGD pile is a bored displacement pile that does not result in drilling spoil. APGD piles are mostly suited for loose to medium granular soils and slightly silty/clayey sandy materials, such as those encountered in Central Florida. The case history presented in this paper involves the APGD piles recommended for a 35-story mixed-use condominium in Downtown Orlando. The subsoil condition was typical for the region; that is loose to medium fine sands underlain by thin layer of plastic sandy clays and plastic clays followed by mixed clayey sands and sandy clays with phosphates and traces of shells transitioned to the weathered limestone. Four APGD test piles were installed and were, statically, tested. Three of the tested piles failed to support the design load. Analysis of load test results showed that the bottom half of the test piles, below the plastic clay deposits, was not effective, which was attributed to structural deficiency resulted from possible pile necking due, in our opinion, to the increase of the porewater pressure within the plastic clays. Three additional test piles were constructed with modified reinforcement cage; that is to extend beyond the plastic clays with tighter stirrups. The additional test piles were, statnamically, tested and were able to sustain the design loads. The construction of the APGD piles through subsoil conditions similar to those of Downtown Orlando, where plastic clayey deposits are encountered, should account for the high porewater pressures that mostly will be developed within the plastic clay, hence, may cause pile necking. Extending the cage to penetrate through and pass the plastic clays reduced the necking potential and improved the test piles performance.

Jan 1, 2006

By Tracy Brettmann

A new method for estimating ground vibrations caused by pile driving was developed as a result of a vibration monitoring program performed for a large pile driving project. The method is accurate, rational and theoretically based starting with energy actually transmitted to the pile (not the rated or operating hammer energy). This energy is then assumed to be transmitted to the soil in the form of surface waves that attenuate from both geometric and material damping. The main input parameters for this method include the energy transmitted to the pile and the dynamic properties of the soil (wave velocity, material damping, and unit weight). In this study we concurrently measured both: (1) pile driving of 14-in.-square, 65-ft-long precast concrete piles with a Pile Driving Analyzer?, and (2) vibration levels at various distances away from the piles during driving. A geotechnical study for the site was also performed that included measurement of the dynamic soil properties using both crosshole and seismic cone testing. This paper presents the data obtained from the study and compares the results to the values estimated using this new method. Vibrations from pile driving is a serious matter that impacts virtually every pile driving project. It is important that accurate methods for estimating ground vibrations be available to engineers and contractors.

Jan 1, 1999

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

By R. V. Huff

An in-situ leaching technology was developed for copper oxide minerals at the Van Dyke deposit at Miami, Arizona. This paper discusses the process developed and the activities that occurred. Specifically, the activities of well installation, deposit data acquisition, leach testing and equipment development are reviewed. Installation and operation of the test facility are described.

Jan 1, 1988

By Norbert Patzelt

The high-pressure grinding roll was introduced about 10 years ago and has established itself in many applications. Most of these machines are used in grinding circuits in the cement industry. A few operate in conventional mineral-processing plants. Polysius has sold more than 350 Polycoms worldwide. An exception is diamond-ore processing in South Africa and Australia. This type of grinding system increases diamond liberation and reduces the capital costs for the downstream processing plant. There are several reasons why high-pressure grinding rolls have not been used more extensively in the mining industry: - The mining industry adheres to conventional grinding technology and regional preference for certain comminution circuits. - Design, scale-up and flowsheet assessment procedures are viewed as being immature and reduce confidence in the potential application of the technology. - Downstream process benefits are unproven on a plant scale.

Jan 1, 1995

By Pierre-Louis Migairou

After a period of development and experimentation ranging over 20 years, electronic detonators have now come to maturity and are becoming the first choice in many diverse applications like tunnelling, civil works, demolition works, quarrying, large scale open pit mining and underground mining. This paper demonstrates the versatility of electronic initiation systems by detailing a number of case studies in several applications as different as their geographical locations, and gives specific reasons explaining the popularity of electronics in each case.

Jan 1, 2009

By Lee R. Buhagiar

As a result of the increased seismic risk and the highly variable geology of Christchurch, finding costeffective foundation solutions has been a challenge for the Canterbury rebuild. The soil profile in Christchurch comprises both terrestrial (Springston Formation) and marine (Christchurch Formation) alluvial deposits with a high groundwater table. The result is a highly variable and interbedded soil profile which is prone to liquefaction and static settlement. Vibro-replacement stone columns are very effective in mitigating liquefaction in clean sand. However, the author’s experience has shown that vibro-replacement stone columns are also effective for treating silty and soft soil layers. Vibroreplacement stone columns can be used to treat these soft soils by increasing the composite soil stiffness and providing a load transfer path to the underlying dense soils. Another challenge encountered in the Canterbury rebuild is the cost of redevelopment of brownfield sites with contaminated fill. The costs of disposing this fill often make projects too expensive. Vibro-replacement stone columns have been used successfully to treat contaminated fill, providing a treated soil profile with uniform performance and reducing the cost of disposing of contaminated fill. This paper looks at several case studies in Christchurch, with highly variable soil profiles, where vibro-replacement stone columns have been used successfully to treat multiple soil layers, from contaminated fill to silty soils and soft and non-liquefiable silt.

Nov 1, 2022

By A R. Bye

The mining industry is facing some key challenges that provide a compelling case for geometallurgy initiatives. Over the last 30 years, the average grade of Australian orebodies being mined has halved while the waste removed to access the minerals has more than doubled. In the last eight years, the industry’s energy consumption has increased 70 per cent while multi-factored productivity has fallen 24 per cent. The paper documents a broad range of industry case studies which demonstrate strategies for gaining value from geometallurgy.The mining industry constantly faces the key questions of how significant ore variability is on mine valuation and how would knowledge of the variability change the mining schedule, mine to mill design and operation. Using case studies the paper describes the methods used for incorporating mineral extraction attributes into orebody models and their technical integration into daily operation as well as mine planning optimisation. While pit optimisation from a fully attributed geometallurgical model highlights areas of opportunity and risk it is shown that during the scheduling phase of mine planning that significant value can be added. The benefits from these projects included reducing geotechnical and environmental risk, improving mine to mill performance, option analysis and quantified cash flow risk. There is growing acceptance within the minerals industry that ‘realistically assumed modifying factors’ defined by a competent person/s are not sufficient to mitigate the risk of funding mining ventures. Geometallurgy is moving away from factored ore reserves to data-rich block models providing reliable information for mining, metallurgical and environmental considerations.

Sep 5, 2011

By I Neilsen, A Walker, A Hooper

Final landform planning in Deswik software was used to determine if integration into the mine plans could achieve better closure outcomes. Using the dump surface outputs from the Deswik Landform and Haulage Simulation (LHS) and the Reshape Landform tool, the project intended to:1.Review costs to achieve the final landform for several grade criteria scenarios;2.Quantify reshape volumes at several stages of the mines development with the objective to contribute to margin ranking inputs; and3.Identify rehabilitation cost reduction measures such as backfilling ramps and pits.CITATION:Neilsen, I, Walker, A and Hooper, A, 2018. Case studies for integrating rehabilitation planning with mine planning in strip mining, in Proceedings Life-of-Mine 2018, pp 93–95 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By S J. Loach

F-Series reconciliations are formal comparisons of estimates and measurements of ore quantity and quality made at pre-determined points along the mining value chain. F1 is the ratio of ‘Depleted Grade Control Ore/Depleted Long-term Model Ore’ and validates the models upon which Resource and Reserve statements are based. F2 is the ratio of ‘Produced Tonnes and Grade/Depleted Grade Control Ore (-) Changes in Pre-Crusher Stockpiles’ and validates that the ore tonnes and grade delineated in the pit are being accurately extracted and correctly delivered to the processing plant. These factors provide important corporate assurance for a mining company by providing quantitative feedback on model-predicted tonnes and block grade estimates. Since 2009, BHPs Western Australian Iron Ore F-Series reconciliations have been calculated in a single, centralised sequel-server database. This software routinely collates data regarding mineral resource block model depletions, grade control model depletions, pre-crusher stockpile inventories and production tonnes and grade measurements and then calculates F-Series factors for both tonnes and product quality. This paper will present case studies where reconciliation factors were used to identify improvement opportunities leading to projects that improved our models and subsequent forecasts of production tonnes and quality. In addition, it will show how reconciliation factors are tools that monitor control during periods of rapid change and provide feedback on the effectiveness of improvement projects.

Sep 18, 2023

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006