Search Documents

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By H. H. Power, Charles R. Houssiere

THE development of effective and dependable methods for drilling through the so-called "heaving-shale" horizons, particularly in the Gulf Coast area, is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Many mechanical remedies have been proposed and are in use in troublesome areas for combating heaving shale. However, in conducting a research program it was concluded that the physical and chemical properties of shales should be investigated, and the effect of added chemicals on such properties determined. As a preliminary step, the effect of chemicals on bentonitic suspensions was determined in accordance with recent contributions in the field of ceramics. The most plausible theoretical explanations for the behavior of the clay minerals involved are offered in the paper that follows. It is hoped that subsequent investigation of actual shale from troublesome wells will be aided by the initial work done on bentonitic suspensions of known composition. INTRODUCTION Formations variously designated as "heaving shale," "sloughing shale" and "caving shale" impede and may even preclude drilling of oil wells, particularly in certain parts of the Gulf Coast. In a previous paper1 it has been stated that the development of effective and dependable methods for drilling through these troublesome beds is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Since the attack on the heaving-shale problem by mechanical means was principally a matter of field investigation, it was concluded that a research program should be concerned with the physical and chemical properties of heaving shales, and the effect of added chemicals on such properties. It was realized that a study of shales required an advanced knowledge of the behavior of the individual clay minerals. A thorough review of the literature led the authors to the conclusion that very recent contributions2.3 in the field of ceramics furnished the most plausible theoretical explanations for the behavior of clay minerals. Accordingly, these fundamental ideas will be used in an attempt to explain the behavior of more complex systems whose composition and replaceable ions are known. In order to obtain comparable results it was deemed important to select an easily procurable clay of uniform characteristics. Accordingly, Wyoming bentonite, which is marketed under the name of "Volclay,"* was used for the preliminary investigations. The chemical analysis reported by the distribution is given as follows:

Jan 1, 1941

By P. Nicholls

PATENT records show that the attempt to improve the burning of fuel by mixture or pretreatment with chemicals dates back to the early years of the last century. By 1845 English and French patents had included the specific beneficiations of elimination or reduction of smoke, soot and clinker; reduction of the ashes; elimination of sulphur fumes; increase of the rate of burning; increase of the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 lb. or more per ton of fuel, but after 1860 the quantity was seldom more than 4 lb. There is no record of the extent to which these patents were commercialized, but after 1874 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many proprietary products were marketed under the general name of "fuel savers," the principal sales being in small packages for the use of householders; savings of from 10 to 40 per cent of the coal were promised. Starting with 1927, the use of proprietary or other mixtures of chemicals was extended to power plants and to treatment of coals at the mines, the claims of saving of fuel being subordinated to those of general improvement and, in particular, to reduction of clinkering. Such expectations are attractive and a number of companies experi-mented with or adopted the practice. There were reports of improved operation, but, apparently, few were confident enough that these improvements were due to the salts to publish the results of tests or their records of operation. There are no data on the yearly tonnage of coal treated but indirect reports suggest that it has been relatively large. Since its establishment in 1910, the U. S. Bureau of Mines has con-tinually received inquiries about these products. At the request of. other governmental departments it made tests in 1910, 1916 and 1930, using certain proprietary products applied according to the instructions of the vendors; these tests were made with eastern coals in domestic and

Jan 1, 1937

Alkaline leaching with sodium carbonate solution adjusted to pH 9·5 to 10·0 preferentially dissolves thorium from a mixture of rare earth and thorium hydroxides. Rare earth sodium carbonates form in the alkaline leaching stage.These are converted to rare earth oxides for use as optical and ophthalmic polishing agents. Quadrivalent cerium is extracted under similar alkaline leaching conditions.INTRODUCTIONAustralia has made significant contributions to mineral chemistry and mineral dressing. As often happens with an industrially immature country, research investigations often outstrip the ability or desire of commerce to exploit them. It is wrong to think exclusively in terms of export of raw materials. Imagination assists in developing world trends. The chemical utilization of mineral sands has interested a group of investigators, chiefly at the Commonwealth Scientific and Industrial Research Organization (C.S.I.R.O.) and, more recently, in the mining industry itself. From an international point of view the highlight of this work was Newnham's (1960) process for the separation of hafnium from zirconium. Earlier work at C.S.I.R.O. investigated the chlorination of rutile, zircon, and monazite. Assuming that titanium tetrachloride would be available in large quantities in the post war years, extensive work was done by Kraitzer, McTaggart, and Winter (1948) on organic compounds of titanium. This work led to the development of heat resistant paints, plastic compositions, and improved organic protective coatings that predated overseas work by up to seven years. (Post, Shiihara and Schwartz, 1961; Anon, 1955). Contributions were made to the production of refractory hard metals (Kraitzer, 1949; Kraitzer and Newnham, 1956). Pilkington and Wylie (1947) and Urie (1947) investigated the production of rare earths from monazite by an acid process.

Jan 1, 1963

By Cyrus W. Field

Chemical, mineralogical, and petrographic data have been obtained for suites of plutonic rock samples from the Guichon Creek Batholith of British Columbia and the Mineral-Iron Mountain-Sturgill Peak- Cuddy Mountain-Peck Mountain areas of western Idaho. Intrusions at these two geographically separate localities represent composite plutons ranging from early gabbro through quartz diorite to late grano- diorite and more silicic-alkalic phases. They are early Mesozoic (200 m.y.) in age, and contain porphyry-type mineralization in close spatial and temporal association with late-stage intrusions of porphyry, aplite, pegmatite, and (or) breccia. Country rocks are eugeo-synclinal assemblages of metasedimentary and metavolcanic greenstones of Permian, Triassic, and Jurassic age. The petrochemical evolution of these intrusions, and the effects of subsequent hydrothermal alteration and metallization, are illustrated by standard ternary diagrams of the major oxide and mineralogical data. Samples plotted on an AFM diagram suggest a calc-alkaline magma trend. However, their distributions on NKC and Qz-Kf-Pf diagram show well-defined trondhjemitic (Na20-rich) and tonalitic (quartz-rich) variants to this trend, which are similar in part to those reported for mineralized island arc plutons of the northern Caribbean and southwest Pacific, but which contrast markedly to those for continental plutons of the Bingham District, Boulder Batholith, districts of southern Arizona, and elsewhere.

Jan 1, 1975

By Michael S. Moats, Jan D. Miller, Wlodzimierz W. Zmierczak

"For many, hydrogen in a pure hydrogen economy would be like natural gas in today’s energy economy. Unfortunately, hydrogen’s physical properties are unsuited to the energy market’s requirements in terms of packaging, storage, transfer, and delivery. In this paper, a hybrid energy economy that packages hydrogen chemically on carbon atoms from various sources including recycled carbon dioxide is introduced and discussed. For this new hybrid energy economy to become a sustainable reality, the ability to recycle carbon dioxide and use hydrogen to create an appropriate energy product, such as dimethyl ether (DME), is needed. DME is recognized as a potential next generation, “beyond-petroleum”, environmentally benign commodity for energy storage and distribution. It is expected that to maximize the sustainability of the proposed hybrid energy economy, “green” hydrogen will be utilized. The “green” hydrogen would be created by the electrolysis of water powered by renewable energy sources, such as solar, wind or geothermal heat.IntroductionWith the growing concerns surrounding trends in global warming and increasing concentrations of “greenhouse” gases, such as CO2 and CH4, efforts to mitigate the emission of these gases from industrial sources are growing. With respect to CO2, the demonstrations of various capture and sequestration methods are underway around the world.The sequestration of CO2 is mainly focused on storing the gas underground or deep in the ocean. The Intergovernmental Panel on Climate Change (IPCC) estimates that 2000 Gtonnes of CO2 can be stored underground in depleted oilfields, un-minable coal beds and other geologic features [1]. Additionally CO2 may be stored at the bottom of the ocean. The lure of storing carbon dioxide in depleted oilfields or un-mineable coal seams is that an economic benefit (enhanced oil or methane recovery) can offset the costs of gas capture, transportation and storage. Unfortunately, all of these storage methods have potential for the release of CO2 or CH4 back into atmosphere or creating environmental damage (mobilizing heavy metals, disrupting deep sea ecology)."

Jan 1, 2008

By Peter Brown

The present work involves the study of Chemical Vapor Deposition (CVD) of silicon carbide from the methyltrichlorosilane (MTS) - hydrogen system. A computer program, SOLGASMIX has been employed to calculate the equilibrium compositions of the gaseous and condensed phases in the MTS - H2 system. The results indicate the range of parameters such as temperature, pressure and species concentrations, required to deposit the single phase Sic under thermodynamic equilibrium conditions. A mathematical model for describing the transport phenomena and the rate of deposition of Sic onto a thin rod in a vertically-oriented hot-walled CVD reactor has been developed. Exper iments were conducted using the same operating conditions as those used in the model in order to validate the mathematical predictions. The predicted rates of deposition were found to be in good agreement with those obtained experimentally. The model can be used to study the effects of various operating parameters on the rate of Sic deposition on a fiber.

Jan 1, 1992

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Y. K. Rao

Relatively pure crystalline lead sulfate (PbSO4) can be produced by chemical vapor transport from an impure source such as the lead-acid battery paste or the roast-ore-leach-residue from a hy¬drometallurgical process-route. In a closed-reactor, transport of matter is induced by a tempera¬ture-gradient and the steady-state transfer rate can be calculated using the data on the standard free energies of formation for the species present and the pertinent binary diffusion coefficients. The present work focusses on chemical vapor transport in a tubular reactor (1.4-cm inner diameter x 10-cm long) with the source- and deposition-ends held at 850°C (T,) and 750°C (Td), respectively; PbC12(g) is the 'solvent' or 'transport agent' and NiSO4(s) placed in the source-zone -serves to maintain a sufficiently high S0,-potential such that the stability of the lead sulfate species is ensured. For the purposes of analysis, the gas-phase in the reactor is assumed to consist of eight species: H2O, PbC12, SO3, SO2. O2 HO, C12, and PbC14. The reaction between C12(g) and PbSO4(s) in the high-temperature source-zone produces PbCl2, SO2, and 02; four more reaction-equilibria in the same zone yield other species. In the low-temperature deposition-zone, reaction equilibrium involving PbC12, H2O, and SO, leads to the nucleation and growth of PbSO4 crystals; three other reaction-equilibria occur in this zone. By employing the virtual equilibrium state for the end-zones and coupling it to the Stefan-Maxwell diffusion equations for each of the gas species, the respective partial pressures for these, in the source- and deposition-zones, are computed at steady-state. From these data, the molar fluxes of PbCl2. PbCl4, and so forth, are determined. Allowing for the transport-enhancing effects of thermal convection, the net transport rate of lead (or PbSO4) is duly calculated for specified initial conditions. The predicted rates show very good agreement with measured rate data reported in the literature [ V. Plies, T. Kohlmann and R. Gruehn: Z. anorg. allg. Chem, 568, 62 (1989)

Jan 1, 1995

By D S. Terekhov, N Victor, M F. OÆMeara

The current extraction method of the Platinum Group of Metals (PGM) from an ore concentrate and the subsequent separation of one PGM metal from another is a timeconsuming complicated multi-step process. The use of the Chemical Vapour Metal Refining (CVMR) process for the extraction and separation of PGMs is a simple and economical alternative. The paper covers the CVMR process, which is based on the formation of volatile metal compounds, followed by extraction and thermal decomposition into the pure metals and reagent gases. In the case of PGMs, CVMR does not use CO, and hence, the process is quite different from the carbonyl process previously attempted by a number of organisations and test facilities. CVMR extracts PGMs via synthesis of trifluorophosphine complexes at low pressures and low temperatures (80 to 100¦C). These two facts alone make the process highly economical, compared to other methods available. This paper presents a comparison between the process of extraction of PGMÆs and CVMR proprietary carbonyl process for the extraction of nickel and cobalt. In the carbonyl process, CVMR also uses very low pressures and temperatures, compared to those other processes currently use.

Jan 1, 2002

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By Kenneth J. Leib, Laurie Wirt, M. Alisa Mast

Chemical-constituent loads were determined for an alpine stream in southwestern Colorado that is affected by natural acid drainage from weathering of hydrothermally-altered rock and from acidic metal-rich discharge from abandoned mines. Base-flow loads were compared to storm-related loads using a tracer-dilution approach. A rainstom occurred during the tracer injection, providing the opportunity to measure metal loads before, during, and after storm runoff. Chemical-constituent loads during the storm increased by 1 to 2 orders of magnitude relative to base-flow conditions. The increase in loads was related to two distinct periods; (1) a flush of higher concentrations that occurred soon after rainfall began, and (2) the peak of storm runoff. The initial flush-having no measurable change in discharge--contained the highest loads of trace metals and dissolved iron. The chemical character of peak runoff was distinctly different, as evidenced by the highest loads of total and dissolved major elements and total iron.

Jan 1, 2000

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By R. Raitani

Five kaolin crudes from the state of Georgia in the U.S. were investigated for processability with chemically enhanced magnetic separation (CEMS) technologies developed by Cytec. The technologies used magnetic reagent alone or in conjunction with specialty chemicals to selectively agglomerate and magnetize the desired minerals (impurities) to be removed by the conventional magnetic separation equipment. All crudes indicated treatability using CEMS. Results indicated that CEMS technology could be applied to different kaolin crudes to obtain a product with titanium impurities less than 0.6% TiO2 from individual crudes. The features and benefits of the technologies were also reviewed.

Feb 1, 2012