Search Documents

By Wendell E. Dunn

INTRODUCTION The early history of the chloride process has been recorded in a chapter of a Bureau of Mines bulletin (9 by one of the inventors of a chloride process, Stewart Croasdale, who is famous for the Pohle- Croasdale Process. The earliest use of chlorine in metallurgy was in 1557 by Bartholome Medina. But apparently even earlier there was knowledge that salt could be used in gold and silver extraction because a treatise, de la Pyrotechnica, published in 1540 in Venice, asserted that silver could be obtained from its ores by a wet salt process. In 1609 a priest, Alonzo Barba, invented a process using a copper vessel and boiling a solution of salt to extract silver chloride ores. The copper vessel was, of course, one of the reactants. This led to the Kronke process introduced in Chile in 1860 which substituted cuprous chloride for the kettle. A major step was taken in Europe in the late 1700's to chloridize roasted silver ores in combination with amalgamation using iron to reduce the silver chloride. By 1843 the Augustan process was introduced. Ores were roasted with salt and leached with a saturated salt solution. The silver chlorides passed into solution from which silver was precipitated by copper. In 1848 sodium or calcium thiosulfate solution of silver chloride was suggested by Dr. John Percy, and the idea was applied in 1856 by Von Patera in Bohemia.

Jan 1, 1983

By T. Inami

The chlorine leach of the anode slime was studied in order to improve the treatment process at the Niihama Nickel Refinery. The anode slime originates from the nickel matte electrorefining and, contains 3-5% of nickel as sulfides. A comparative study has been conducted on the filter cake resulting from the sulfur filtration of the molten anode slime. The kinetic factors of the chlorine leach such as temperature, grain size were defined. Under the optimized condition, 70-80% of the nickel is recovered from the slime or filter cake. On the basis of these results, the chlorine leach process for the treatment of anode slime has been established. The leaching plant has been installed and successfully operated since 1986.

Jan 1, 1988

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

The author presents various procedures for the choice of dri-ving systems for mining, including the method of indeterminate Lagrange factors and linear programming.The possible application of the points-awarding method is demonstrated.It allows for taking into account both surd and commensurable characteristics of a driving system for mining. Also, the method of economic efficiency factors is outlined.All these methods make possible the best choice of a driving system, from the as-pect of electric energy saving. Two examples are given.

Jan 1, 1985

By FRANK RIEBERS

IN DISCUSSING the selection of a geophysical method, much of what the writer will say is applicable to any of the various methods and to their use in prospecting, whether for oil or for other minerals. Specifically, the writer's subject is the problem, particularly pressing on the Pacific Coast, of checking the rising cost of the discovery of new fields by the proper employment of geophysical methods. Table I was prepared from statistics published by the California State Milling Bureau. The writer selected five of the largest a:ld most active companies operating in California, segregated the number of wild-

Jan 1, 1930

By E. De Golyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is one of selecting test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favor- able, were usually found in anticlinal types of structure. This very understandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in parallel planes. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades, the majority of the known important oil deposits of the world have been discovered. This is but an incomplete, and the simplest, statement of the problem. Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps- anticlines, faulted structures, salt domes, etc.-but by

Jan 1, 1932

By Hans Lundberg, Basil T. Wilson, H. Steuart Scott

FOR the benefit of those readers who may not be in close touch with present practices in the geophysical prospecting for ore, brief reference will fiat be made to the advantages and shortcomings of the methods to be discussed. Magnetic and electric methods are generally accepted as the most useful for ore prospecting. By magnetic methods, magnetic intensities that are not normal may be recorded and outlined. From these can he located concentrations of such highly magnetic minerals as magnetite or pyrrhotite, which sometimes occur in such large masses that they are of economic value in themselves. More often. however, these magnetic min¬erals are associated with others, such as copper, zinc, lead, gold, and silver, which, if existing in sufficient concentration and quantity, may constitute valuable ore bodies. It is therefore only when pyrrhotite and magnetite are present in these bodies that the magnetic method can be used to indicate their presence.

Jan 1, 1945

By Pope Yeatman

In my experience, perhaps the most interesting problems came up during the testing, prospecting, developing and equipping of the Chuquicamata and Braden Copper Mines in Chile, and it is proposed in this article to give as briefly as possible what some of those problems were, their solutions, and the decisions made as to the different methods to be employed. The romance of mining is still a great lure to the young man who is making a choice of a profession to follow. The thought of travel to strange and out-of-the-way places, the glamor of pioneer life, the excitement of discovery, the constructive work of building something, entirely "from the grass roots up," or of reconstructing a played-out property and making a success of it-all of these phases have a strong appeal and often influence the young man in the choice of mining as a profession. That great engineer, Col. Seeley Wintersmith Mudd, whom we are endeavoring to honor, while having too much common sense to have been materially influenced by the romance of mining, certainly experienced all of the

Jan 1, 1932

By Jorgen Elbrond, Yve Lizotte

"A mine evaluation method based on the use of a computer program that models mining with an open-ended dynamic program is presented in this paper. It is demonstrated with an example how the method is applied, how some of the decision variables are related in the particular industrial environment and how these decision variables affect the economic benefits of mining.IntroductionTwo distinguishing characteristics make mining a particular industrial environment: exhaustible resources of a given ore deposit and heterogeneousness of the ore grade spatial distribution in the ore deposit. These characteristics, inflation, uncertainty and cyclical price variations which greatly affect estimated cash flows also contribute in rendering difficult the evaluation of the economic outcome of mining at the preliminary planning stage.Decision variables and their ranges are associated with the mine plan; basically, they include choices of the mine's nominal capacity (mining and milling), the sequencing of mining through the deposit, the ranges of possible production rates and cutoff grades, and the stockpiling policies. The mine's nominal capacity must be decided at the planning stage, but this capacity choice must take into account flexibility to modify other decision variables as mining commences and uncertainty resolves.Although it is generally accepted in discounted cash flow analysis that the sequence of mining must proceed from the richest to the lowest-grade stopes (with correspondingly ajusted cutoff grades), this may not produce optimum benefits when cyclical price variations are considered.Mining rates and cutoff grades can also be adjusted to changing economic conditions, taking into account the limited resources of the ore deposit. Thus, when prices are thought to be in the trough of a cycle, production can decrease to preserve ore for expected greater future profits. When prices rise, mining rates can increase possibly even over the mine's nominal capacity. In both cases, the machinery's effectiveness shall not be-optimally utilized; this will be reflected particularly by the variations in the concentrator's metal recovery and the concentrate grade output."

Jan 1, 1982

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By Newell G. Alford

With the workable area of coal prospected and known as to workability and quantity and sampled and tested for desired quality comes the determination of the projection and method of working. The best method will be the one supplying the greatest degree of safety, the most merchantable product, the minimum average cost per ton with the largest yield of recoverable coal. Based on coal elevations, taken at the bottom of the seam on all known outcrop exposures, prospect openings or drill holes, coal contours are made on the map to be used in developing the mining plan. The contour interval should be as close as available information will permit. For general utility in layout of mining, haulage, drainage and ventilation, a map scale of 400 ft. per in. is preferable. In mountainous sections, location of the main out- crop opening or hoisting shaft is often limited by the available railroad route and amount of land level enough for a plant site. In level country, where a tipple and hoisting shaft may be placed at will, choice of the plant site should depend on the minimum average underground haul for the total coal to be worked to the new

Jan 1, 1932

By S. Epstein

THE new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the con-struction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attrac-tive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately 18,27,28,29,30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved.

Jan 1, 1936

"INTRODUCTION Foam, unless intentionally created, in any industrial process presents operational problems, or at a minimum, is a nuisance. Some foam problems are unique to a given industry and others are common across many industries. A few problems foam presents to any particular industry are: (a) Poor Housekeeping, (b) Environmental impact, (c) Safety Hazards, (d) Slower Production Rates and, (e) Reduced quality of the end product. Defoamers address these issues. Sadly, the assumption in most industries is all defoamers are alike. In reality, a lot of chemistry is involved in the manufacture of even the simplest defoamer sold today and rarely are any two defoamers “just alike”. Today’s defoamers can include polymer chemistry, fatty esters, alkoxylated alcohols, silicone chemistry, silicone surfactants, ethoxylated and propoxylated block polymers, and a tremendous amount of emulsion chemistry just to name a few. This paper will discuss the various types of defoamers, defoaming mechanisms, the advantages and disadvantages of defoamer selections, and how to choose the proper defoamer for your application. Before a discussion of defoamer can be brought about, foam generation and composition must be discussed. WHAT IS FOAM? Foam is a colloidal suspension of a gas dispersed in a liquid. Most often foam consists of air dispersed in water. If a stream of air is introduced into a liquid, the bubbles produced assume a spherical shape. As the density of the bubble is less than the liquid the bubble rises. When the individual bubbles reach and pass through a surfactant free liquid they collapse. Air from the bubble dissipates and the liquid previously surrounding the bubble flows back.It should be noted a pure liquid will not foam. In the case of air dispersed in water a surfactant is necessary to make the water support a stable foam. A surfactant is a term used to describe a surface active agent; a compound with a hydrophilic end and a hydrophobic end on the same molecule."

Jan 1, 2016

By Sami Hindstrom, Travis Orser, John Starkey

"A great deal of effort has been expended in the last 11 years by the authors and others to identify the correct power required to grind ore in a SAG mill, by developing ore hardness variability functions for the ore body to be mined. This paper describes the next step in the SAG design process, which is choosing a SAG mill to accomplish the required specified design performance.At the test work stage, each ore hardness data point is a unique and discreet bit of information that represents the energy required to grind the ore represented by that sample at optimum SAG conditions. When the design criteria are set, it is now considered necessary that the required power draw in the mill chosen be provided at optimum conditions as well.Based on actual 3-ft diameter pilot plant results, we can now show that the grinding efficiency and throughput drop when the optimum load limit is exceeded. Future work is expected to show a similar reduction in efficiency when exceeding optimum speed. Providing specified power by exceeding these optimum conditions is not adequate and leads to a lower cost but underperforming SAG mill.It is possible in some cases to modify a SAG circuit to force it to perform better, but this often takes time, much effort and costly modifications. In most cases the capital spent on a properly sized SAG mill may prevent production losses that would be many times greater over the extended start up period. This is the direct result of choosing the proper SAG mill at the start.INTRODUCTIONThe sequential steps required for the design of any grinding circuit, have changed dramatically in the last seven years. Previously, it was considered necessary to do six foot diameter SAG mill pilot plant tests on representative samples of minus six inch ore (F80), in order to understand design requirements. It can now be shown that this method is costly and not likely to produce the desired result because it is difficult to recover six-inch material from deep within a new mine. The representative nature of the sample is often compromised when the sample is selected."

Jan 1, 2003

By Robertson GE, McLaughlin JD

An extensive laboratory campaign was conducted to find a suitable water soluble collector to replace diphenylguanidine (DPG) in the matte separation process. The examination of the collectors was done by measuring the rate of flotation and the best candidate collectors were selected on the basis of the rate parameters. As a result of this search mercaptobenzothiazole (MBT) was selected for a plant trial. A plant trial of two weeks duration confirmed that MBT will produce separations at least as good as those obtained with DPG.

Jan 1, 1993

By Mark William Johns

Carbon-in-pulp (CIP) is the preferred method of gold recovery om cyanided plp. However, other gold adsorbents (namely, ton-exchange resms) are being introduced to the industry as they are considered to have several advantages over carbon for the recoery of gold. A set of test methods have been developed by the industry to evaluate the quality of different carbons. owever, many ?f these tests are not applicable to evaluating ton-exchange resms. Hence, a need has arisen for a method to evaluate the different adsorbents. This paper introduces a philosophy to evaluate an adsorbent that results in an estimation of the capital cost and the operating cost associated with the adsorbent. Tests that have been devel­ oped to evaluate the ability of an adsorbent to adsorb gold (in­solutton . counter-current) and to evaluate the optimum adsorbent for a specific pulp (in-pulp batch) are introduced. A method of converting the test data into an economic dimension is present­ed. Case studies are presented to highlight the discussion.

Jan 1, 1996

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

Choosing an Effective Dust Suppressant

Sep 13, 2010

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

Provide guidance on the selection of millisecond initiator delays between blastholes in surface mine blasting to provide a desired degree of rock fragmentation consistent with safety and vibration considerations. The Problem Blasting remains the primary means of fragmenting, rock for all kinds of mining, quarrying, construction, and excavation activities, and it is the only practical and economic method of breaking up and moving large amounts of material such as coal overburden and stone aggregate. Because of the large amount of blasting done, typically using 4 billion pounds of explosive to break about 8 billion tons of rock annually in the United States, a small improvement in blasting performance will have a significant productivity impact. Standard blasting practices involve the selection of time delays in a blast for at [cast three purposes: (1) to control energy flow to minimize adverse vibrations, (2) to provide sufficient time relief for good rock displacement, appropriate muck pile shape for digging, and the prevention of collar violence, misfires, and flyrock, and (3) to provide an appropriate amount of interhole stress wave and gas pressure action for a desired fragmentation size distribution. Timing guidelines that exist are based on subjective observations rather than measurements, even for the relatively new casting methods. Until this Bureau study, no definitive analysis had been done to quantify the fragmentation and productivity of full-scale blast rounds as functions of precision delay timing.

Jan 1, 1989