Search Documents

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By G. P. Halliwell, C. R. Austin

The investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at t,he Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word ''Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 per cent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy," or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limitJ' has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend test developed by Howard Scott.' In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1932

By Wilson Blake

Increased application and interest in the use of microseismic monitoring to deal with ground control problems, Particularly those resulting in violent failures, has brought about the need for practical guidelines with respect to all phases of microseismic monitoring. This report presents the results of an 18-month effort to review the microseismic method and develop needed practical guidelines. Microseismic activity and properties of microseismic events are treated so that these parameters can be taken into account when developing monitoring equipment. Microseismic equipment is discussed to provide familiarization with the components of monitoring systems. Factors to be considered and procedures for developing a microseismic monitoring system are presented. Both physical and electrical considerations for the installation of a monitoring system are discussed in detail. The operation of a microseismic system including data analysis procedures is presented. Field examples to illustrate use of microseismic data in evaluating ground control problems are presented in a number of case histories.

Jan 1, 1982

By Harold J. Bennett

This study was performed by the Bureau of Mines to evaluate the potential supply of primary copper from domestic resources. A tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, smelting, and refining the copper. Total known recoverable copper resources are 189 million short tons of which 83 million tons could be economically recovered assuming a price of $0.50 per pound of copper, credit for the recovery of byproducts, and a 12-percent rate of return on capital investment. The quantities of recoverable byproducts associated with the 83 million tons of recoverable copper are molybdenum, 1.8 million tons, gold, 43 million troy ounces, and silver, 740 million troy ounces.

Jan 1, 1973

By S. A. Montague

In spite of the many new insulating materials, both synthetic and manufactured, that have been put on the market since the end of World War II, and notwithstanding the many millions of dollars applied to the development of synthetic mica, natural block mica1 is still a most indispensable insulator in various electronic components. It will remain so, barring some spectacular break-through in research that might provide a substitute fully acceptable as a replacement for mica in all of its superior properties. But this is not to say the future for mica is assured, or free from serious problems. Technological advances have created problems requiring a solution to be found if future requirements are to be filled.

Jan 1, 1962

By Jacek Paraszczak

L?exploitation rentable des gisements de type filonien constitue un problème important dans le contexte actuel de l?industrie minière québécoise. Les études effectuées depuis 1994 ont indiqué, que la technologie d?abattage mécanique utilisant l?outil hydraulique appelé « éclateur radial-axial » constitue une alternative intéressante par rapport aux méthodes conventionnelles par le forage et sautage. Les essais du prototype de l?éclateur ont prouvé qu?il est en mesure d?abattre les roches dures dans un environnement minier, mais sa performance dans les termes de masse du roc abattu dans une unité de temps a soulevé certaines doutes. Pour cette raison, une étude de préfaisabilité de l?éclatage en tant qu?une technologie d?excavation souterraine a été réalisée. Cet article présente quelques résultats des travaux effectués dans le cadre du contrat octroyé à l?Université Laval par le Ministère des ressources naturelles du Québec. Leur objectif principal consistait à comparer, pour les conditions des gisements filoniens, la productivité et les coûts des méthodes d?exploitation souterraine utilisant l?éclatage par rapport à celles conventionnelles. Deux variantes proposées de cette méthode ont été comparées avec la méthode conventionnelle sur le plan du coût (par tonne de minerai) et de la teneur de coupure de minerai d'or. Les études ont démontré que l?application de l?éclatage représente un potentiel de réduire ce coût, surtout dans les situations où l?abattage sélectif pourrait avoir lieu. Pour le cas de base on a trouvé, qu?il serait possible de réduire la teneur de coupure par la marge d?environ 16 ? 26%. Toutefois, les études de sensibilité ont démontré, que le coût dépend de façon important de la productivité d?éclatage, qui, pour sa part, varie beaucoup en fonction de paramètres du massif rocheux devant être abattu.

Oct 1, 2001

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973

By Alfred Bellows

The objective of this contract is to design, build and demonstrate a support system to improve roof control in the entries of longwall mines. The objective of this phase has been the detailed design of such a system and the selection of a test site in which to perform the pilot demonstration. The result is a complete set of detail drawings or specifications which define the three major components of the system. The Gate Support is a variation of a face chock which has an extended canopy and additional hydraulic legs to protect the region of the face-entry intersection. The Entry Support is a steel beam and hydraulic prop set which is reusable and serves to support the first 100 or more feet of entry inby the longwall face. The Transporter is a bolter-like vehicle with a crane used for installing and retreating the beam sets. The test site selected is CF&I's Allen Mine in Colorado. They presently use simi¬lar steel beams and expect the FMA support system to be more effective as well as recoverable. It is recommended that the completed drawings be used to build a prototype system and test it first in a remote section of the mine and then in the active longwall tail entry.

Jan 1, 1978

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood-block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 2010

By Z. Saw, C. Poveda, N. L. Mai

Optimising the throughput of a mining network comprising all equipment from shovels to semi-autogenous grinding (SAG) mills is a complicated task, yet the potential benefits can be significant. Key modelling challenges stem from the sheer number of possible routes which material can travel, different equipment operating under different constraints, and the rate of SAG mills being calculated through a nonlinear function of the blended materials’ rock attributes. Nevertheless, this is an ideal onapplication area of mathematical programming, a branch of operations research. This paper describes an application of mixed integer linear programming (MILP) to optimise the mining equipment network of one of the world’s largest copper mines.The model takes as input a year-long monthly mine schedule of shovels in different pits, pushbacks, sequences and faces which produce material to be moved through a network of crushers, conveyors, silos, distributors, stockpiles and SAG mills, ultimately outputting a daily operational plan for all equipment that maximises the throughput of the network. All operational constraints and business rules are considered, including three quality attributes of copper ore. Comparing model results with actual data shows an improvement of 4.47% in network throughput tonnage. Additionally, although the model is solved using a free, open-source solver, optimal solutions are still achieved within a practical timeframe.

Sep 1, 2021

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By Oliver Bowles

Accidental explosions in coal mines are due to various causes, but many of them can be directly attributed to coal dust; others that probably in no way depend on dust as a primary cause are propagated, greatly intensified, and made more disastrous by the presence of coal dust. The fact that coal dust in a bituminous mine will explode as a result of a fire-damp explosion has been generally accepted for many years, but the belief has also been held by many that coal dust is not in itself dangerous when unmixed with an explosive gas. Therefore, in past years little attention was given to dust in mines free from fire damp, and many disastrous explosions have resulted from lack of knowledge of the danger from coal dust. In the explosives gallery and experimental mine of the Bureau of Mines experiment station, Pittsburgh, Pa., it has been proved repeatedly and conclusively that coal dust will explode violently when no inflammable gas is present. PROPAGATION OF DUST EXPLOSIONS A coal-dust explosion is an extremely rapid burning or combustion of the coal particles. Their burning consists essentially of the combination of the hydrocarbons in the coal with the oxygen of the air, a process that generates heat and flame and produces hot gases and water vapor. These gases and vapors have a volume many times that of the original coal particles; thus they exert an outward motion and pressure which constitute the explosive wave. When fine particles of coal are suspended in the air, each particle is surrounded by the oxygen of the air, and thus is well placed to oxidize or burn rapidly whenever the temperature is high enough. If some particles are ignited from any cause they will fire others, and the combustion will extend from particle to particle with extreme rapidity wherever enough coal dust of sufficient purity is present.

Jan 1, 1925

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999

By R. R. Sayers

The hazards connected with work under abnormal air conditions are becoming of increasing importance from a financial as well as a physiological stand- point, due to the extension of compensation laws to include diseases caused by dusts, toxic gases, and abnormal temperatures and humidities. The United States, with the excention of California, North Dakota, Wiscon- sin, Massachusetts, and Connecticut, is the only English-speaking country to-day where silicosis is not compensated.3 Cases of permenent total disability or death due to silicosis mar aprear in common-law courts, particularly in the States that have not recognized silicosis as an occupational disease for which compensation should be provided. Such cases have recently been tried in one State, according to a magazine editorial, not providing scheduled commensation for employees affected by silicosis, with results favorable to the claimant. Clearly established cases definitely linked with occupation as the cause may be expected to be recognized as deserving by juries and courts, and awards will be made. In one Atlantic Coast State, according to this editorial, 108 claims for silicosis, including 21 deaths therefrom, are said to have been filed against two small plants engaged in finely pulverizing quartz sand.

Sep 1, 1932

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d'interface et un modèle constitutif sont développés. Dans le but de valider l'applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

Once and for all, the debate on the exponent in Gy's formula is pushed to its limit. It is explained why an exponent of 2.5, obtained when using a square root of nominal size d to adapt the value of a calculated liberation factor to a different comminution size, will rarely be encountered in practice, if no arbitrary decisions are made.

Mar 1, 2010

By Oliver Bowles

[Simple systematic accounting that adequately records all transactions has long been regarded as essential to the welfare of any business enterprise. Some of the defects that detract from the prosperity of the slate industry are attributable to a lack of effectiveness in cost keeping. This condition has promoted the United States Bureau of Mines to make a detailed study of accounting methods for the slate industry, and to present for consideration a system of accounts, which it is believe would enable the industry to attain more economical management and operation if accepted by a fair proportion of its important units. The method of accounting presented herein has been worked out with the assistance of leading slate producers and the recommendations are tentative and are submitted in this form as a means of developing constructive criticism. Believing that cooperative effort in this, as in many ether problems will bring the most enduring benefits to the industry as a whole, the writer urges that the cost earnest consideration be given to this vital problem now facing the slate industry.]

Jan 1, 1929

By T. Krichler

"Current mine control stations are either single-position systems with high engineering effort or all-in-a-box solutions with low integration possibilities of third-party devices. Above all, both approaches are cost-intensive and not feasible for small companies. This paper shall be an inspiration of how to enhance the productivity and monitoring of an existing mining system in a modular way by introducing a proven technique of the ongoing digital revolution: A Wi-Fi network based on the communication protocol OPC UA. The starter kit consists of a single-board computer, a WLAN access point and any electronic sensor. INTRODUCTION The majority of the European mining industry is run by small and medium deposits (Europe Geology, 2017). This is due to the fact that most ore mines in Europe are widely distributed within the continent, are generally small and additionally they are often steeply inclined. Such ore bodies are normally mined with underground mining methods and must be excavated with high selectivity because of their small thickness. That is why the economy of scales, higher efficiency through bigger machines, cannot be used in most deposits in Europe except for lignite mines. It is important to find an alternative possibility to improve the efficiency of European mines for making them competitive internationally. For cost optimization and profit maximization it is necessary to use the trends of industry 4.0 and to broadcast these into the mining industry to reach a technological advantage. The goals of the EU within the Horizon 2020 funded project are to shorten the actualisation of the mine and block model to hours, improve the communication with Through the Earth (TTE) via very- or ultra-low frequency for long-time monitoring of the abandoned workings, and develop a cost-effective mine control station for optimization of mining processes in Small and Medium Enterprises (SMEs) as well. This paper deals specifically with the new approach for data acquisition, transmission and visualisation of a mine. SCADA AND ERP IN MINING There are already many Supervisory Control and Data Acquisition (SCADA) and Enterprise Resource Planning (ERP) programs on the market, but these are normally not developed for the mining industry. At the moment this leads to three options. • To hire a system integrator, who shall build a complete control station for one mine that requires a high amount of knowledge in programming and cannot be maintained by the mining company itself. • To buy different types of out-of-the-box systems, whereby every system can include some of the used technology. In this case a huge amount of project engineers and operators – at least one per system and shift- is required. • To buy every machine and program from one company including the service contracts."

Jan 1, 2018

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013