Search Documents

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Alan Rice

Abstract-The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultramafic igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on fluid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other fields dealing with suspended loads in fluids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Peter Waggitt

Northern Australia has been home to uranium mining for over 70 years, more or less continuously. In the early days, post World War 2, there was little effort made to remediate workings at the end of operations. The three “campaigns” of uranium mining (1951-55; 1960-70; and 1979-present) are all now in various stages of remediation. This includes not only the large legacy site at Rum Jungle but also smaller fields like the South Alligator Valley, as well as contemporary works at Nabarlek and the ongoing closure at Ranger– Australia’s longest operating uranium mine. This paper briefly describes some of the past remediation activities before providing an update on the Ranger closure programme and future timetable.

Jan 1, 2020

By C. Babcock

When a flat-lying mineral deposit such as a coal seam is mined, some coal is left to separate the roof and floor so that miners and machines can safely mine the seam. The mineral left is in the form of mine pillars. If too much is taken, support problems and unsafe working conditions result. If too little is taken, the mining operation will be unable to compete economically with other mines. Therefore, one must select pillars of the optimal size to maximize mining recovery and minimize risk to miners and equipment. Later, if the pillar support is no longer needed and the surface can be allowed to subside the thickness of the coal seam, then the pillar support can be removed to increase mining recovery, and initial pillar size is not as critical. Only a small part of the information available on pillar design can be presented here. The purpose of this report is to summarize some of the work done by the U.S. Bureau of Mines and others on pillar design, which is reported in the literature from 1833 to the present, and present rock mechanics test results that aid in understanding mine pillar behavior. The variable names used are those of the authors cited. This results in multiple use of some variable names.

Jan 1, 1994

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By Olga Frank-Kamenetskaya

The experimental results of study of atmospheric corrosion processes on Saint-Petersburg bronze monuments surface, received in situ and by means of simulating experiments, have been discussed. Influence of the time factor on corrosion film (patina) mineral composition has been analyzed. Direct dependence between patina mineral composition and environmental conditions has been proved. The sequence of patina phases crystallization has been established. Effect of the chemical composition and heterogeneity of artistic bronze and also monument surface structure on the rate of corrosion process has been regarded. The time variations of mass of the crystallized in the hydrochloric acid vapor phases have been investigated. The kinetic laws of their development at the initial stage of formation, indicating simple (non chain) reactions, have been revealed.

Jan 1, 2006

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By S. Fuentes, J. Cáceres

"During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs.This paper describes improvements in mine design, mine planning, and mine management, including methods enabling the Chilean and international mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low-cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine. IntroductionDuring the last fifteen years, block caving mines have experienced huge changes in designs, planning and administration. These changes have permitted operators to drastically reduce costs, improve equipment productivity, and improve overall business performance. As a consequence of this situation, the block/panel caving mining system is challenging actual open pit operations to maximize the net present value (NPV)."

Jan 1, 2004

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

By P. J. van der Walt

The paper1(hereinafter BG) by two respected sampling experts contains sound theory and logic that can?t be directly refuted. Nevertheless, a practitioner knows that there is a broader context in which the practice of sampling takes place. This broader context, being less well defined than the theory of correct sampling, receives correspondingly less exposure which this commentary??prompted by? BG?seeks to rectify. ?Correctness? of a sampler is the central concern of BG, where it is presented as a sharp ?black-and-white ?distinction. Accordingly, comments below are grouped under the following headings: ?Correctness in practice ?Without correctness, what can be done? ?The broader context.

Jan 1, 2002

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

The functional design of a pavement relates to the selection of appropriate wearing course materials which optimise the trafficability of a pavement. Trafficability is dictated to a large degree by the choice, application and maintenance of locally available wearing course materials. Poor functional performance results in decreased safety and operational efficiency and increasing road and vehicle maintenance requirements. An optimal functional design will include a certain amount and frequency of maintenance (watering, grading etc.) and thus maintenance itself can be planned, scheduled and optimized within the limits of required road performance and minimum vehicle operating and road maintenance costs. Since no wearing course material selection guidelines, tailored to the specific needs of surface mines, were available, there was the need to identify appropriate selection guidelines for the range of materials commonly encountered for road building on South African mines. The aim of this paper is to present an overview of the functional design method for mine haul roads and, through an analysis and quantification of existing wearing course material performance, to recommend appropriate wearing course material selection guidelines. The functional design technique has been applied at a number of mines and is illustrated by an application case study which demonstrates the potential reduction in total transportation operating costs associated with the optimal functional design.

Jan 1, 2000

By T. K. Perkins, L. R. Kern, R. E. Wyant

Many factors influence the results of hydraulic fracturing to stimulate well productivity. Most of these factors have been studied and their effects discussed in the literature. However, the movement of sand through the crack during fracturing has received little consideration. Exactly where the sand goes in the fracture, how it gets there, and how this might influence results have not been studied, judging from published reports. To get an answer to some of these questions we have studied sand movement through a simulated crack segment in the laboratory. Although the work is preliminary, we have answered some questions about sand movement in a semiquantitative sense. We are reporting our results at this time in the hope of stimulating interest and further study in this important aspect of fracturing. LABORATORY EXPERIMENTS Fig. 1 is a schematic diagram of equipment used in this study. A segment of a vertical crack 0.25-in. wide was formed between two Plexiglas plates, and movement of sand in fluid through the crack was observed under various conditions. Sand and fluid were injected into the crack at constant rates. The top and bottom of the crack were closed so that the fluid flowed horizontally. Because of gravity most of the sand settled to the bottom before moving very far through the crack. If the fluid velocity exceeded a certain critical value, then all the sand injected was washed on through the crack even though it had settled to the bottom. When the fluid velocity was less than this value when sand injection was started, most of the sand which settled in the crack remained in place until enough of the area open to fluid flow was blocked by the settled sand to increase the fluid velocity to the critical value.. At this point all injected sand moved on through the crack even though it settled to the lower portion of the moving fluid section. All sand previously settled remained in place. When fluid velocity was increased at this paint by increasing fluid injection rate (without also increasing sand injection rate), some of the previously settled sand was washed out until enough area was open to flow that the velocity dropped to the critical value. Conversely, when the fluid velocity was decreased by decreasing the fluid injection rate (without changing the rate of sand injection), additional sand would settle until the critical velocity was again attained. In short, the critical velocity is an equilibrium value which the system will automatically seek, if possible. The equilibrium (or critical) velocity was measured under several conditions. The results of these measurements are shown in Pig. 2 where the equilibrium velocity is shown as a function of the amount of sand injected per minute. The points falling in the shaded band shown in Fig. 2 were obtained with water. The higher viscosities were obtained by adding CMC (carboxymethylcellu-lose). Data indicate that the equilibrium velocity is not very sensitive to sand size or transport fluid viscosity, or to sand injection rate (except at very low rates). Points connected by the solid CUrve in Fig. 2 were obtained with water and 20- to 40-mesh steel shot. The equilibrium velocity is apparently fairly sensitive to difference in density between particle and fluid. Only one run was made with a gelled fluid and that was gelled water at zero sand injection rate as shown in Fig. 2. (Measurements of equilibrium velocity at zero sand injection rate were made by filling the crack