Search Documents

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

Surface Chemistry of Iron Ore Throughout a Processing Plant

Sep 13, 2010

By K C. Williams, A W. Roberts, J D. Prigge

For stockpile design, the flowability and structural interfaces are critically dependant on the stress conditions throughout the pile. Historically, the predictive methodologies for stress determination have been too conservative, which adds inefficiency to the stockpile reclaim interface selections, especially for live reclaim stockpile systems. In addition, accurate pressure profiling throughout stockpile is essential to correctly design the stockpile support structures, which are buried within the stockpile. Such buried structures include trestle legs or columns to support load-out conveyors or the roof of bulk storage sheds. Improved methodologies with respect to the development of the hoop stress condition which exists in material ædrawn-downÆ within the stockpile has been developed. This hoop stress approach has significantly improved the live capacity prediction to over 90 per cent accuracy and improved rathole structure prediction within live reclaim stockpiles. Additionally the methodologies in estimating the vertical and circumferential stress variation acting on buried stockpile structures have been significantly progressed, with experimental testing shown good agreement with the theory.CITATION:Williams, K C, Roberts, A W and Prigge, J D, 2013. Recent developments in stress analysis and live reclaim prediction within iron ore stockpiles, in Proceedings Iron Ore 2013 , pp 501-510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By A M. Purba and A Sjadat, A D. Wilson

Ongoing mining of the East Ertsberg Skarn System orebody below the Gunung Bijih Timur and Intermediate Ore Zone caves has been relatively successful and a ramp up to 80 000 t/d was achieved in the Deep Ore Zone Mine. However, the distribution of production, the overall drawpoint availability as well as the rate of change of the cave back profile has not followed the anticipated path. Several key factors influencing cave growth and progress, grade variation, fragmentation, wet muck and surface subsidence have been recognised over the life-of-mine that now have to be taken into account for planning the later stages of mining.The paper will discuss the influence of geological controls of lithology and structure – how this as well as other contributing aspects have impacted ore flow, contributing to some of the widespread panel damage, and been a key factor in compacted draw columns and caused an accelerated appearance of water ingress. This in turn has rapidly changed the distribution of wet drawpoints requiring remote mucking and special controls that also affect the call from the remaining dry drawpoints. Comment is also made on the potential final cave profile if it continues along the current trend and some discussion is offered about possible mitigation measures if this were to come about.CITATION:Wilson, A D, Purba, A M and Sjadat, A, 2016. Progressing cave performance into the later stages of the Deep Ore Zone mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By L Bartsch, M Kelahan, E Wingate, J-S David

The use of column flotation cells for recovery of phosphate is becoming more common practice in certain parts of the world (Brazil, Russia) where igneous phosphate ores are processed. Igneous phosphates are generally finer grained (< 200µm) than some of the traditional sedimentary phosphates (<400µm). Australian phosphate from the Georgina basin is sedimentary, but has a much finer grain size (typically < 106µm) than similar deposits in North Africa and the USA.In 2013, Arianne Phosphate completed a bankable feasibility study for the development of their igneous phosphate deposit at the Lac a Paul site in Quebec. Initially, lab test work and bench scale piloting indicated that using traditional mechanical flotation would be able to produce adequate concentrate grade and an economic level of recovery, but would necessitate the installation of a complex and operationally challenging flotation circuit. Later pilot plant testing using column cells resulted in a significant reduction in process complexity and facilitated the processing of the -20µm ore fraction which resulted in a 10% increase in P2O5 recovery and a 5% increase in concentrate grade %P2O5.Flotation column testing achieved a concentrate grade of 38.6% P2O5 at a P2O5 recovery of 90%. Using a mechanical flotation cell circuit, the concentrate grade was 36.4% P2O5 with a P2O5 recovery of only 78.8%. A noticeable feature of the testing was the simplicity of the column flotation circuit configuration (Rougher + 2 stages of cleaning + Cleaner Scavenger) compared to the mechanical flotation cell circuit (Rougher + Scavenger + 3 stages of cleaning).The financial benefit for this case study was estimated using a sales price of US$ 195/t FOB for a 38.6% P2O5 product, and an assumed cost of production of US$ 95/t, the netback price is calculated at US$100/t. For a daily milling rate of 55,000t/d, the improved flotation performance provides additional concentrate production of 1,203t/d. Using the netback price calculated above, this calculates to additional gross profit of US$ 120,260/d.Annualised, this equals US$ 40.7 million in additional revenue for a similar or reduced CAPEX.The use of column flotation on fine grained phosphate ore types often requires fine grinding and desliming to liberate the phosphate value, such as the Australian sedimentary phosphate ores. This may enable the development of deposits previously regarded as uneconomic.This paper discusses the potential benefits available to operators, and developers of new projects, for the use of column flotation cells in their metallurgical circuits as assessed by an engineering company.CITATION:Wingate, E, Kelahan, M, David, J-S and Bartsch, L, 2015. Does it make cent$ to use flotation columns for phosphate beneficiation?, in Proceedings MetPlant 2015, pp 353–365 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Ecological Fuel from High-Sulfur-Content Coal

Sep 13, 2010

By K. M. Mayhew, G. D. Barr, T. M. McCoy, C. T. Knilans

"Teck Resources Limited (“Teck”) has developed and extensively tested on a continuous basis the CESL Technology hydrometallurgical process for treating copper and nickel sulphide concentrates, including bulk copper-nickel concentrates. Copper, nickel and cobalt are leached efficiently into solution, utilizing CESL process conditions. Total precious metals including gold, silver, platinum and palladium are recovered from the residue stream via sulphur flotation. This paper describes the CESL Technology testwork on a bulk copper-nickel concentrate derived from Twin Metals Minnesota?s (TMM) deposits within the Duluth complex and evaluates the economic benefits (increased cash flow, increased revenue certainty) and investment criteria (capital cost, payback and cash flow) of incorporating CESL Technology into the staged development of TMM?s deposits.INTRODUCTION Mineral Processing and the Role of Hydromet in the Duluth Complex The Duluth Complex in northern Minnesota, United States (US), represents one of the largest undeveloped accumulations of copper, nickel, gold, and platinum group metals (PGMs) in the world, ranking second in copper and PMs and third in accumulation of nickel. The figure below identifies some of the larger known deposits within the Complex (see Figure 1). Copper, nickel, PM and PGM mineralization within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex.One of the mineral processing challenges of Cu-Ni-PM-PGM deposits in this Complex is the complicated, polymetallic nature of the mineralization1: copper occurs primarily as chalcopyrite and cubanite with minor occurrence of talnakhite; nickel occurs as pentlandite and refractory nickel oxide/silicates; iron sulphides are present as both pyrrhotite and troilite; and PMs/PGMs occur in both the sulphide matrix as well as discrete minerals. An additional challenge for the Duluth Complex is the ratio between copper and nickel; in most of the identified deposits, copper grade is three to four times greater than the nickel grade, which precludes the production of a simple bulk concentrate due to the lack of a traditional smelting market for a bulk concentrate of this character."

Jan 1, 2017

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

A large number of brittleness concepts have been used in very different studies in the literature. One of them is the B1brittleness concept. In this study, the objective is to criticize the B1 brittleness concept on rotary blast hole drills. The B1 brittleness concept, the ratio of uniaxial compressive strength (sc) to tensile strength (sT), are widely used as a rock brittleness concept in the literature (Inyangand Pitt, 1990; Verhoef, P.N.W. 1993; Neil, D.M. et al.1994;Becker, et al.1984; Evans and Pomeroy, 1966; Göktan, R.M.1992; Kahraman, S. 2001; Yamaguchi, U. 1970; Verhoef, P.N.W. et al.1996; Bilgin, 1982; Howarth and Rowlands,1987; Howarth, D.F. et al. 1986). So, it was used as a rock brittleness concept in this article. The value of the B1brittleness concept is equal to the tangent of ß angle in the following graph. It was seen that more meaningful relationships could be obtained with the B2 brittleness, the under ?Area?(= 1/2(scxsT) = B2) under the curve, instead of tangent ß, (=B1), of the curve.

Jan 1, 2003

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002